• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Seat mounting bolt

jerry

Contributor
Sr. Member
Joined
Jan 28, 2002
Messages
778
Loc.
Bakersfield, CA
Sorry for such a simple question.

Does anyone know where I can find a couple of these?

They're used to mount the seats in my '70. Bolt head is 5/8", and they take a 5/16" nut. Overall length is approx 2 1/16".

Page 30 of the repro body and interior assembly manual suggests it's bolt "H" (also shown as "R") with a part # of C6TB-9660056.

I know I could work around this a couple different ways... But thought I'd ask first. Thanks in advance!
 

Attachments

  • Seat Mounting Bolt - w ruler.jpg
    Seat Mounting Bolt - w ruler.jpg
    143.7 KB · Views: 251
  • Seat Mounting Bolt.jpg
    Seat Mounting Bolt.jpg
    107.7 KB · Views: 253
  • one.jpg
    one.jpg
    176.4 KB · Views: 162
  • two.jpg
    two.jpg
    173.5 KB · Views: 233
Last edited:

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
You said seats, plural, so apparently it’s not a bench seat.
I can’t say I’ve ever seen a bolt like that holding a bronco seat in place. What does the sleeve go through?
Is it going into the floor and there’s a nut underneath?
Sounds a little strange, but it has been a while since I’ve played with factory bolts. Usually they are just simple body bolt types with a captured washer under the hex head. Threads into a captured nut under the floor.
Or rather than captured, they are more like fixed nuts, welded to the floor.

Got a picture of what these go through? We probably have standard seatbelts available, but not sure they would fit what you have.
Or are they the bolts for the pivot points on the seat back?
 
OP
OP
jerry

jerry

Contributor
Sr. Member
Joined
Jan 28, 2002
Messages
778
Loc.
Bakersfield, CA
Paul,

Laughing at myself a bit. What I thought was a simple question and I didn't provide nearly enough information, and the info I provided wassn't the best example. Sorry about that.

Yes, bucket front seats on my '70 (build date of October '69).

I also realized there's a better diagram, and added this to my (revised) original post. These bolts have the long shoulder to fit through the "rib" that reinforces the body.

The bolt comes up through the bottom of the floor and provides a stud for seat mounting.

The way I see it, my other options would be to make something somewhat close using a bolt and a piece of tubing as a sleeve, or enlarge the holes in the ribs so I can get a wrench in there...

Or, maybe a shorter bolt that takes an allen key?

Thanks again!
 
Last edited:
OP
OP
jerry

jerry

Contributor
Sr. Member
Joined
Jan 28, 2002
Messages
778
Loc.
Bakersfield, CA
I probably just answered my own question... Am going to go by the bolt place today to see if they have a grade 8 bolt with a hex head to use insead.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
If you are tall, you might want to use this opportunity to move the seat back a little bit.
You can create your own “nut plates“ and even glue, or weld them to the floor for additional support and ease of maintenance.
Then just use a standard bolt.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Thanks for the extra diagram. When I first started reading originally I thought that you were talking about the seatbelt bolts. They have an odd shank design that allows easy pivoting.
Now I can see the setup.
Must be yet another small change made between the’70 and’71 model years.
The drawing shows a completely different design for the passenger seat latch too. Never seen one like that.
Looks like something a van would have had.

If you look at the bolts holding the passenger pivot bracket to the front floor, you can see the bolts that I’m used to seeing in all positions.
At least on the mounting feet. Haven’t looked at one for the latch lately.
 

thegreatjustino

Contributor
Red Head Grease Monkey
Joined
Jan 23, 2002
Messages
16,291
Loc.
Stockton, CA
@jamesroney check out the last two photos in the original post. There's a part number listed for your passenger seat latch you're looking for (or one similar to it)
 

bigjhoov

nobody
Joined
Apr 10, 2005
Messages
3,583
I've never seen those, most seats I've seen bolt from the top of the floor to a captured nut. But it explains why the holes in the stock seats are so big. Ive always wondered if they were supposed to use a shoulder bolt of some sort.
 

jamesroney

Contributor
Bronco Guru
Joined
Sep 11, 2007
Messages
2,607
Loc.
Fremont, CA
@jamesroney check out the last two photos in the original post. There's a part number listed for your passenger seat latch you're looking for (or one similar to it)
Hey @thegreatjustino Thanks a TON. I found item 11, the C7TB-96619A86-A Latch Assembly, Passenger seat. Great to know. Now just need to find one!

As far as the seat shoulder bolt goes, @DirtDonk and @jerry you have missed the point. Those seat bolts are designed to retain the seat in the event of a collision. There are three locations where that special 5/16-18 shoulder bolt with a 5/8 hex head are used. I have removed many originals, and they are prone to twisting off at the thread base. The bolts are designed to provide a secure connection to the seat riser, AND the oversized hex head is designed to provide additional tear out resistance against the lower hat channel reinforcement bar.

It would have been easy for Ford to install a nut plate in that location, but they apparently wanted the additional strength of the structural member (hat channel) to support the seat to prevent pull thru. So the shoulder near the threads sandwiches the floorpan, and the shoulder near the hex head sandwiches the hat channel.

This is a safety device, and it should not be neglected. There is NO regular bolt that can serve the same purpose. I started boring my old broken one's out and threading and inserting a dog-point stud into the old bolts. No matter how many I make, it seems that people want them. You can get away with using a long flange head bolt with a spacer. I've also put the bolt in from the top, and added the spacer on below and then tightened with a flange nut.

The old bolts usually get stuck on undercoating and fall out sometime after seat removal, and before paint. Most of mine are out on the interstate somewhere, or perhaps in your tire.

I've thrown away more than my fair share...always wondering who put that oddball shoulder bolt under my Bronco. I think Nick had some repop'd for like $40 each. Or maybe $40 a set.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
I think I was just forgetting how the originals worked. After a day of cogitating on it all, I now seem to remember removing just nuts on the originals, at least in some positions, even on my '71.
I've long since replaced them with bolts and nut plates, when moving the seat rearward for more legroom, but a stud with a nut does now sound familiar. Wishful thinking maybe?

So James, just what is it about this design that gives them extra strength for this application? I hear you on the larger head, but that alone does not seem to justify anything. And given the same size thread at the business end, what dynamic is at work that gives this design an advantage?
Very curious now.

Thanks

Paul
 

jamesroney

Contributor
Bronco Guru
Joined
Sep 11, 2007
Messages
2,607
Loc.
Fremont, CA
I think I was just forgetting how the originals worked. After a day of cogitating on it all, I now seem to remember removing just nuts on the originals, at least in some positions, even on my '71.
I've long since replaced them with bolts and nut plates, when moving the seat rearward for more legroom, but a stud with a nut does now sound familiar. Wishful thinking maybe?

So James, just what is it about this design that gives them extra strength for this application? I hear you on the larger head, but that alone does not seem to justify anything. And given the same size thread at the business end, what dynamic is at work that gives this design an advantage?
Very curious now.

Thanks

Paul
You are going to make me sketch this? OK. The larger head is designed to contact the hat channel only in the event of deformation of the floor pan. In a rear end collision, the tissue paper floor pan gets ripped out by the shoulder, and the head of the bolt then contacts the much thicker hat channel.

A regular bolt would crush the hat channel. And a regular shoulder bolt would pull thru the floor metal. And a normal shoulder bolt would require a different nut, and our UAW install team only has a 1/2 inch wrench! But a special, small diameter, large head, custom length shoulder bolt would be just the ticket! Impossible to install with one person, impossible to prevent rotation, guaranteed to rust, and prone to break off, fall off, or get lost. Then very unlikely to be replaced in the event of seat removal. It's Brilliant!

I also used to think those were studs, and was praising my media blaster for getting the studs out. Then I actually looked at it and thought: "wait a minute..."
 

Attachments

  • CFF7E4BC-67D3-4717-A036-54C8F2B54957.jpeg
    CFF7E4BC-67D3-4717-A036-54C8F2B54957.jpeg
    99.8 KB · Views: 230

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Thank you very much. Especially for the sketch!
I see what you're saying in general, but is there any downside to the threaded stud-ish end being surrounded by the floor panel? Any chance of it shearing off in a less-than-catastrophic incident?
I've never heard of that happening, and the designers have been at it a long time, but it just looks sketchy all necked down there like that.

Paul
 

Speedrdr

Contributor
Legend in my own mind
Joined
Nov 27, 2017
Messages
2,028
Loc.
Paris, MS
You are going to make me sketch this? OK. The larger head is designed to contact the hat channel only in the event of deformation of the floor pan. In a rear end collision, the tissue paper floor pan gets ripped out by the shoulder, and the head of the bolt then contacts the much thicker hat channel.

A regular bolt would crush the hat channel. And a regular shoulder bolt would pull thru the floor metal. And a normal shoulder bolt would require a different nut, and our UAW install team only has a 1/2 inch wrench! But a special, small diameter, large head, custom length shoulder bolt would be just the ticket! Impossible to install with one person, impossible to prevent rotation, guaranteed to rust, and prone to break off, fall off, or get lost. Then very unlikely to be replaced in the event of seat removal. It's Brilliant!

I also used to think those were studs, and was praising my media blaster for getting the studs out. Then I actually looked at it and thought: "wait a minute..."
@jamesroney, just to understand the sketch (which I saved) is this view from underneath the floor pan? I remember taking the seats out of the ‘72 I had in 1980 but don’t remember THAT amount of detail. Great engineering drawings, by the way. I will refer to it in the future, I’m sure.

Randy
 
OP
OP
jerry

jerry

Contributor
Sr. Member
Joined
Jan 28, 2002
Messages
778
Loc.
Bakersfield, CA
I've never seen those, most seats I've seen bolt from the top of the floor to a captured nut. But it explains why the holes in the stock seats are so big. Ive always wondered if they were supposed to use a shoulder bolt of some sort.
There are a couple of captured nuts too. Total "parts bin"
Hey @thegreatjustino Thanks a TON. I found item 11, the C7TB-96619A86-A Latch Assembly, Passenger seat. Great to know. Now just need to find one!

As far as the seat shoulder bolt goes, @DirtDonk and @jerry you have missed the point.
No, I didn't miss the point, and did consider the forces being exerted during a rapid decelleration. Hence all the questions about "what is this / where can I get one" vs "hold my beer while I widen the hole in the channel and use the cheapest hardware I can find". :)

I'm sticking with the stock seat locations for now. In lieu of that specialized shoulder bolt, I'll u se a grade 8 hex drive bolt (from a reputable hardware store) that will fit through the hole in the rib. I'll put a washer on it (just like the factory), then through the floor pan, just like the factory.
If I were to shift the seats to an alternat position... I do think it would be important to ensure the new mounting position was reinforced.

Glad my pictures were able to help!
 
Last edited:

hsach

Contributor
Members Only
Joined
Apr 19, 2013
Messages
435
I am missing one of my 3 seat bolts that the OP attached a picture of. I have my 2 passenger side bolts, but I can't find the one for the driver side. I looked at Notheast Classic to see if they had some, but couldn't find any. Are they available anywhere? I am going to order the Wildhorses4x4 Caballo seats and install them in the factory location, so I was hoping to use the factory style seat bolts in those front hole locations.
 
Top