• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Holley EFI Problems

J-man

Sr. Member
Joined
Feb 5, 2011
Messages
568
Loc.
Holladay, UT
Last year before Bronco Safari I installed the Holley EFI Kit I purchased from Wildhorses. The kit was a simple install, I mounted the high pressure fuel pump on the frame and converted my 23 gallon fuel tank for this application. This particular kit did come with the digital control panel which I mounted in the Bronco. While at Bronco safari the everything ran well, the only problem I encountered was the digital screen was not responsive at times and would on ocassion lose the ability to change settings etc. This didn't seem to harm the performance of the vehicle. After bronco safari last summer I took the bronco for a drive on a pretty warm day and the bronco was running hot, I pulled into a gas station for a drink and the bronco wouldn't start. I had to wait 30-45 minutes before it would start. I'm suspecting that the fuel pump and fuel got to hot and vaporized, with the exhaust next to the pump. On cooler days the bronco would run ok and never stall out like this.
Forward to about a month ago I had to drive the bronco for about a week straight because my daily driver was in the auto body shop. Everyday I drove the bronco at least once usually multiple time the bronco seemed like it would go into limp mode with little power. It acted like one of the plug wires was pulled off and ran like crap. After a couple minutes the bronco would go back to full power and running normal. This happened at all stages in the drive sometimes first thing and sometimes when fully warmed up. Now keep in mind the digital controller has not been functional for me like it is froze up, cant change setting or navigate through the screen. I am baffled to why the bronco runs like this, does it have something to do with the EFI, o2 sensor, or fuel issue. I'm thinking its electrical but not sure. I called Wildhorses and they said Holly has been having issues with these screens and no longer offer them and all service would have to be handled from Holley directly.
I need to resolve this issue before taking the bronco back to Bronco Safari this year.
I am planning on putting an in-tank fuel pump in to help resolve this fuel heating issue.
Any advise will be amazing.
Thanks Rick
 

raleigh_bronco

Bronco Guru
Joined
Sep 25, 2002
Messages
1,567
Other than your vapor lock issue I suggest that you do a little research Sniper EFI problems. Google EFI System Pro and click on the Sniper hangout section. Make sure you have the latest firmware and also read the EMI commentar.
 

raleigh_bronco

Bronco Guru
Joined
Sep 25, 2002
Messages
1,567
Other than your vapor lock issue I suggest that you do a little research on Sniper EFI problems. Make sure everything in your engine bay is properly grounded (see Holley instructional video). Then Google EFI System Pro and click on the Sniper hangout section. Make sure you have the latest firmware and also read the EMI commentary. Also note that Blueprint has installed an EMI shield in front of the Sniper on their engines to apparently solve the EMI dilemma.
 
OP
OP
J-man

J-man

Sr. Member
Joined
Feb 5, 2011
Messages
568
Loc.
Holladay, UT
Other than your vapor lock issue I suggest that you do a little research on Sniper EFI problems. Make sure everything in your engine bay is properly grounded (see Holley instructional video). Then Google EFI System Pro and click on the Sniper hangout section. Make sure you have the latest firmware and also read the EMI commentary. Also note that Blueprint has installed an EMI shield in front of the Sniper on their engines to apparently solve the EMI dilemma.
What are you referencing with talking about EMI dilemma?
 

omureebe

Contributor
Sr. Member
Joined
Jun 18, 2013
Messages
419
I read your screen isn't functioning for changing parameters, but is it datalogging? That's always handy with diagnosis. I'm a FiTech person, and found a number of issues that way.
 
OP
OP
J-man

J-man

Sr. Member
Joined
Feb 5, 2011
Messages
568
Loc.
Holladay, UT
I called Holley the other day and they advised me to take a teeth flosser pick and run between the screen and frame around it on the handheld unit. Looked like this fixed the screen and now i can use the functions. I started the bronco and seemed to run good for a minute then randomly out of nowhere it runs rough like timing is off.... especially at low throttle somewhat seems to clear a bit when I give it throttle. So I'm now assuming the screen wasnt the issue. Are there any tips on where to set all the setting for the 351 stock cam? I may need to reset then start from scratch. Always seems to idle fine. I'm kinda lost at this point as what to do next.
 

pcf_mark

Bronco Guru
Joined
Jun 11, 2010
Messages
3,697
I feel terrible for people when they have these electrical gremlins they are very difficult to diagnose remotely. I will say this from experience. I personally know a car with Sniper highest end model, Holley fuel support, all the bels and whistles. It always had reliability problems it would just run bad and then die. After 3 YEARS of trying to sort it out including Holley tech support the owner bought a new wiring harness and it has been fine ever since. That said..

When it is running rough put a timing light on #1 and see how the light strobes. Repeat on each cylinder. If they all strobe the same and it is consistent you have completely eliminated the timing side of the system from spark plug to EFI controller.

Put an old school vacuum gage on it and see what it reads when it is running good and when running bad and let us know what that says.

When it is running poor un-plug the IAC and see what happens. Does it smooth out but drop to a low rpm? If so prop the throttle at a steady RPM and see if it runs ok. This will help you see if it is in the idle control circuit.

Trying to eliminate a few things will help find areas to look deeper in to that are more complex.
 

fluffybunny

Full Member
Joined
Oct 28, 2015
Messages
219
My brother-in-law had issues similar to that. After sending it to 2 shops who claimed to be well versed in Snipers, he got it back running just as bad as when he took it in. They were nice enough to bill him $150/hour for their multiple conversations with Holley tech support to the tune of about $2000. Once he got it back, he had conversations with Holley who finally told him to ship the unit back for a rebuild. He did that and rather than waiting two months to get it back, he bought a refurb unit off of their website. We installed it and it's been running fine. When they repaired the original unit, they told him that they they found a couple of loose connections in the TBI unit and that the held-held was bad. They shipped it back repaired along with a new hand-held and new wiring, O2, etc. I bought it from him and put it on mine and it works fine.

If going through the set-up wizard again and doing the things that pcf-mark suggests and not getting it to line out, I think you'll have to ship it back to them.

From all I can tell searching the holley forum, you really need a laptop and versed in how to read/tune the tables to really understand what the system is doing and how to fine tune it. That's above my skill level and luckily we found a guy that knows how to do that. Mine is still running off of the base tune set by the wizard because my rebuilt motor only has 150 miles on it.

Hopefully, you don't have to resort to that but I'm interested in your problems so keep us updated. Good luck, something which seems like should be so simple can cause a ton of frustration.
 
OP
OP
J-man

J-man

Sr. Member
Joined
Feb 5, 2011
Messages
568
Loc.
Holladay, UT
My brother-in-law had issues similar to that. After sending it to 2 shops who claimed to be well versed in Snipers, he got it back running just as bad as when he took it in. They were nice enough to bill him $150/hour for their multiple conversations with Holley tech support to the tune of about $2000. Once he got it back, he had conversations with Holley who finally told him to ship the unit back for a rebuild. He did that and rather than waiting two months to get it back, he bought a refurb unit off of their website. We installed it and it's been running fine. When they repaired the original unit, they told him that they they found a couple of loose connections in the TBI unit and that the held-held was bad. They shipped it back repaired along with a new hand-held and new wiring, O2, etc. I bought it from him and put it on mine and it works fine.

If going through the set-up wizard again and doing the things that pcf-mark suggests and not getting it to line out, I think you'll have to ship it back to them.

From all I can tell searching the holley forum, you really need a laptop and versed in how to read/tune the tables to really understand what the system is doing and how to fine tune it. That's above my skill level and luckily we found a guy that knows how to do that. Mine is still running off of the base tune set by the wizard because my rebuilt motor only has 150 miles on it.

Hopefully, you don't have to resort to that but I'm interested in your problems so keep us updated. Good luck, something which seems like should be so simple can cause a ton of frustration.
Thanks for the message. I want to try to reset the tuner back to stock and reinstall the program, this is after I check timing on the plugs. What I dont understand the most is why it would run totally fine then out of the blue run like shit on and off. I can mention too that it idles fine, and at higher RMP seems to clear out and run fine but midrange its got a miss/ runs crappy randomly. ugh
 

rexorcist

Jr. Member
Joined
Aug 1, 2012
Messages
66
similar issues…runs great for awhile but eventually get afrs in the 20s with notable power loss, stumbling and dying..sometimes spontaneously recovers and runs great..got the recommended shield… seriously considering going back to carb
 

turbotim2

Contributor
____________
Joined
Jun 26, 2003
Messages
2,158
I have been battling my Sniper for several years. One problem after another. I had the electrical problem early on and fixed it by moving the wiring around several times until it was in a place where it has been stable and using relaysdirect to the battery for the ECU and ignition. This problem is typically revealed by the Sniper ECU rebooting itself while the engine is running and you will see the screen restart.
Most recently I had the bad injector connector problem, they come loose. It's a fairly easy diagnosis and fix.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,112
similar issues…runs great for awhile but eventually get afrs in the 20s with notable power loss, stumbling and dying..sometimes spontaneously recovers and runs great..got the recommended shield… seriously considering going back to carb
That sounds like fuel supply dropping out. That's when you need a data log to see if the injector pulse shuts down or not.
Next it could be ignition. No fire, it will read lean since there is all that unburnt air in the exhaust.
Have to check everything, can't assume that it is only the EFI
 

MonsterBIlly

Sr. Member
Joined
Dec 17, 2015
Messages
461
Last year before Bronco Safari I installed the Holley EFI Kit I purchased from Wildhorses. The kit was a simple install, I mounted the high pressure fuel pump on the frame and converted my 23 gallon fuel tank for this application. This particular kit did come with the digital control panel which I mounted in the Bronco. While at Bronco safari the everything ran well, the only problem I encountered was the digital screen was not responsive at times and would on ocassion lose the ability to change settings etc. This didn't seem to harm the performance of the vehicle. After bronco safari last summer I took the bronco for a drive on a pretty warm day and the bronco was running hot, I pulled into a gas station for a drink and the bronco wouldn't start. I had to wait 30-45 minutes before it would start. I'm suspecting that the fuel pump and fuel got to hot and vaporized, with the exhaust next to the pump. On cooler days the bronco would run ok and never stall out like this.
Forward to about a month ago I had to drive the bronco for about a week straight because my daily driver was in the auto body shop. Everyday I drove the bronco at least once usually multiple time the bronco seemed like it would go into limp mode with little power. It acted like one of the plug wires was pulled off and ran like crap. After a couple minutes the bronco would go back to full power and running normal. This happened at all stages in the drive sometimes first thing and sometimes when fully warmed up. Now keep in mind the digital controller has not been functional for me like it is froze up, cant change setting or navigate through the screen. I am baffled to why the bronco runs like this, does it have something to do with the EFI, o2 sensor, or fuel issue. I'm thinking its electrical but not sure. I called Wildhorses and they said Holly has been having issues with these screens and no longer offer them and all service would have to be handled from Holley directly.
I need to resolve this issue before taking the bronco back to Bronco Safari this year.
I am planning on putting an in-tank fuel pump in to help resolve this fuel heating issue.
Any advise will be amazing.
Thanks Rick
The fuel pump is getting too hot. It really needs to be mounted in the tank. I went through this same ordeal.
Once you mount it in the tank you will no longer have issues.
 

turbotim2

Contributor
____________
Joined
Jun 26, 2003
Messages
2,158
Do you have an inline pressure gauge? Is the pump producing the correct pressure? Have you checked that all injectors are delivering the correct amount of fuel?

I would confirm this before doing anything with the pmp.
 
Top