• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Heater hose routing

brad smith

Jr. Member
Joined
Aug 16, 2017
Messages
136
Loc.
tupelo ,ms
I’m full of questions. And I know this has been a topic before. But doesn’t anyone have a diagram of the heater hoses with the control valve showing in it? Thanks
 

Glass Pony

Contributor
Bronco Guru
Joined
Feb 13, 2012
Messages
1,954
Loc.
Sussex County Delaware
Not a diagram. Hope it helps.
2019-09-15 19.34.55.jpg
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
And for reference, at least up to 72 before they added electrical input to the choke, the “upper“ heater hose was routed from the front of the intake manifold with that 90° elbow, past the carburetor, where it sat in a little trough (for lack of a better term), that held the hose next to the choke spring housing to add a little controlled heat to it.
This was just before it went to the heater control valve and then on to the heater core.
That hose’s heater core fitting would’ve been the one closest to the driver side.

Only factory carbs had that curved hose holder. Aftermarket carburetors use the electric only.
 

jamesroney

Contributor
Bronco Guru
Joined
Sep 11, 2007
Messages
2,612
Loc.
Fremont, CA
It doesn't matter which direction the coolant flows through the heater core. It's actually good to reverse it occasionally to remove sediment deposits.

(click this text)
Yup. Note that the heater core flow is reversed from V8 to I6 in the pic by @Oldtimer.

BTW, @DirtDonk are you sure about that choke heater function? I had that argument with my dad, and he convinced me that I'm an idiot.

His assertion is that the exhaust gases get warm long before the coolant gets warm, and that the water would never be used to heat the bi-metal spring on the choke...because the exhaust gas is always hotter than the coolant. Operative word being coolant. At steady state, and fully warmed up, the excess heat from the exhaust is not needed. The heater hose is used to remove heat, and keep the choke cooler.

I have found that it is pointless to argue with him.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
No, that sounds perfectly legitimate and even more logical than the part about adding heat.
I never followed through with my thinking, but I always wondered about it because, exhaust heat or not, it always took all the Broncos I knew a long time to warm up enough to do any good.
Although, a few years down the road, when all of the exhaust riser tubes have rusted out or been removed, maybe that heater hose actually did help add some heat.
Sort of a backup, so to speak. 😁
 
OP
OP
brad smith

brad smith

Jr. Member
Joined
Aug 16, 2017
Messages
136
Loc.
tupelo ,ms
No, that sounds perfectly legitimate and even more logical than the part about adding heat.
I never followed through with my thinking, but I always wondered about it because, exhaust heat or not, it always took all the Broncos I knew a long time to warm up enough to do any good.
Although, a few years down the road, when all of the exhaust riser tubes have rusted out or been removed, maybe that heater hose actually did help add some heat.
Sort of a backup, so to speak. 😁
Did they have mounting parts thst the hoses ran through or were they just laying up on the intake area or fender well?
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
The upper hose is attached to the tubing elbow right on top of the intake. So it’s pretty solid there.
Then it lays in a curved tray that holds it right up against the choke housing. Not far behind that is the heater control valve, floating there on the cable.
So while it’s not really considered to have mounting brackets on the intake manifold, it’s pretty well supported until it turns down and over to the heater core.

The lower hose just floats around. Many of us have added clamps, or clips, or zip ties, or whatever, to support that hose.
Nothing from the factory that I remember.
 

Oldtimer

Contributor
Jr. Member with Sr. moments
Joined
Feb 4, 2005
Messages
1,801
Loc.
Sunnyvale, CA
68 Bronco had a clip on firewall that supported both hoses.

2023-09-07_093252.jpg


Pick up (2) GATES 28471 heater hoses. 5/8 x 40"
They work well to to turn 90 degrees at heater core fittings.

hose.jpg
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Wow, nice! And here I even looked under your hood recently, and missed that neat detail.
And you're an "almost" original owner if I remember. You think it was factory, or added?

All the ones I remember had that lower hose just sort of "out there" without much in the way of hold-downs. My '79 has one of those band clips though.
Maybe it was added when the 351 was installed?
I don't remember, but was that your dad that did the engine swap?

Thanks for posting that pic.

Paul
 

Oldtimer

Contributor
Jr. Member with Sr. moments
Joined
Feb 4, 2005
Messages
1,801
Loc.
Sunnyvale, CA
And you're an "almost" original owner if I remember. You think it was factory, or added?
I don't remember, but was that your dad that did the engine swap?
Paul
2nd owner.
I would say it was factory. It was there when I bought Bronco in 73, and it had dealer applied undercoating on it.
(I don't think undercoating was a factory option?)
I installed 351 in 1985.
 
OP
OP
brad smith

brad smith

Jr. Member
Joined
Aug 16, 2017
Messages
136
Loc.
tupelo ,ms
The upper hose is attached to the tubing elbow right on top of the intake. So it’s pretty solid there.
Then it lays in a curved tray that holds it right up against the choke housing. Not far behind that is the heater control valve, floating there on the cable.
So while it’s not really considered to have mounting brackets on the intake manifold, it’s pretty well supported until it turns down and over to the heater core.

The lower hose just floats around. Many of us have added clamps, or clips, or zip ties, or whatever, to support that hose.
Nothing from the factory that I remember.
I have another question. I am replacing the elbow fitting going in to intake. I noticed when I pulled mine out it doesn’t have the extra stem past the thread. Does it need this stem or can it just be the threaded part and no stem. All I’ve seen pics of is mainly the stem type. It’s a 3/8 pipe with a 5/8 barb hose Thank you
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
I’m not 100% certain on the purpose of the stem, or siphon tube, or whatever that appendage would be called. But I believe that it either enhances flow, or more likely that it takes its water from lower in the area, closer to the, bottom surface of the manifold, probably to get hotter coolant flowing through.
Used to think it was there to enhance flow, but it’s probably just to ensure that the hottest coolant goes to the heater.
Maybe it’s also less disruptive to flow through the thermostat.
Personally, I’ve always used the appropriate fitting.
 
OP
OP
brad smith

brad smith

Jr. Member
Joined
Aug 16, 2017
Messages
136
Loc.
tupelo ,ms
I’m not 100% certain on the purpose of the stem, or siphon tube, or whatever that appendage would be called. But I believe that it either enhances flow, or more likely that it takes its water from lower in the area, closer to the, bottom surface of the manifold, probably to get hotter coolant flowing through.
Used to think it was there to enhance flow, but it’s probably just to ensure that the hottest coolant goes to the heater.
Maybe it’s also less disruptive to flow through the thermostat.
Personally, I’ve always used the appropriate fitting.
Thank you
 
Top