• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Crankshaft Pulley Diameter Difference?

NJBronk

Contributor
Sr. Member
Joined
Oct 11, 2022
Messages
369
I’m in the process of replacing my harmonic balancer and was thinking about replacing the three groove crank pulley with a two groove (I have AC and power steering that run off the first two belts and the pulley has a lot of surface rust in the grooves).

I saw this 5.75” OD pulley on wild horses: https://www.wildhorses4x4.com/product/Billet_Crank_Pulley_6668yr/bronco_pulleys. But mine seems to be 6.25” at the outer edges. Does this matter? Or could it be the mating surfaces are the same diameter and mine just has a bigger “lip”?

Here is mine:

IMG_0180.jpeg

IMG_0178.jpeg
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,114
A 3-groove 3-bolt crank pulley is pretty rare.

Going down in crankshaft diameter slows down the accessory drive. Slower turning water pump, fan, alternator, power steering pump. Does that matter? Maybe. Depends on how boarderline you are.

Does that system charge? With how little belt wrap there is on the alternator I am expecting charging system issues.
I have seen in the past a regular alternator belt arrangment (crank-alternator-waterpump) or even just crank and alternator (skip the waterpump since the power steering belt is running that). Then run a seperate belt off the second groove of the alternator to the A/C.
 
OP
OP
NJBronk

NJBronk

Contributor
Sr. Member
Joined
Oct 11, 2022
Messages
369
Running two belts (one "regular" and one just between alternator and A/C) or isolating the alternator is an interesting idea...

Maybe I'll just keep the existing pulley and try to clean it up. I'm afraid to paint inside the grooves because it seems that would inevitably wear off. Any ideas for cleaning up the pulley grooves?
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,114
The belt riding on the pulley will do a really good job cleaning itself.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
A lot of surface rust? I see an absolutely minimal amount, that wouldn’t hurt anything.
As Broncobowsher said, a minute or two of spinning with a properly tight belt would polish it off.
And most belts don’t end up riding all the way down in the bottom of the groove anyway.

Have you run it in this configuration before? With the AC compressor in place?
As was also mentioned, that is a ridiculously small amount of belt to pulley contact surface area. Not enough for most normal use.
Maybe under perfect conditions where the battery is almost always fully charged, you won’t have an issue. But as soon as the alternator is called upon to put out more than a minimal amount of current, the belt will just slip.
You might not hear it in the usual squeal (or you might) but it’ll certainly reduce its ability to recharge the battery and power the system.
Believe it, or not, even the power steering system needs less attention than the alternator does. Especially a higher output alternator.
Part of the reason is because the power steering pulley is much larger. But also is under fairly consistent resistance, until you put it under more stress. Whereas the alternator resistance varies over a wider range more often.

Is that a muffler band clamp on the upper radiator hose?
Using it to clamp the hose, or to protect the upper hose from a flipping air conditioning belt?
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Protecting the upper hose is a critical disaster prevention method. So if that’s what that clamp is for, it’s a good idea.
But you might try something else too, just in case it can work for yours.
The later model thermostat housing has a more vertical aim, as opposed to the angled aim of the early style like you have.
You might need to use a different upper hose, or modify, yours more likely. But it would put that section of hose further out-of-the-way.
Might help, or it might cause problems if your particular set up, doesn’t allow for the vertical Jose orientation. Only you can know by either drawing it out or mocking it up.
Or if it’s an option, you can change the location of the compressor to maybe utilize that front groove and get the belt out of the way of the hose that way.

Back to that lower pulley. Generally speaking, you are on the right track by getting rid of that extension and using a shorter pulley just to get more radiator and fan clearance.
But there are trade-offs to both ways, as you are finding.
 
OP
OP
NJBronk

NJBronk

Contributor
Sr. Member
Joined
Oct 11, 2022
Messages
369
Thanks, @DirtDonk

I have run this configuration, but I have only really taken short trips (maybe up to 45 mins away) and I keep the battery on a tender in the garage. So potential charging problems may just not have shown up.

That is an exhaust clamp... The PO had just used a zip-tie to keep the hose away from the belt and I forgot to put it back on after fixing an intake leak and the belt cut a hole in the hose. I replaced the hose and put the clamp on as a temporary solution. I wish I had considered the 90-degree thermostat housing when I replaced mine, but I was (and am) undecided about a lot of things so I figured I'd wait. But maybe it's time to reconsider that.

I'm still thinking about just getting rid of my AC, which would solve a couple of these problems... But if I ever need to take a longer trip with the top on in the summer (rain) then I might regret it...
 

Slowleak

Bronco Guru
Joined
Sep 12, 2013
Messages
4,013
Loc.
Georgia
You might be able to run three belts to get better contact. Mine is stock with dealer added air and is setup this way.

Rear belt on the crankshaft, waterpump, alternator.
Center belt on the crankshaft, waterpump, power steering.
Front belt on the crankshaft, idler pulley for tension adjustment, a/c compressor.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Yeah, and I think at least some of the three groove/sheave pulleys on Broncos were installed after the fact, just for the dealer installed air-conditioning.

There might be another way too. A dual groove pulley on the alternator could utilize the existing belt, plus the front belt.
But looking at the original picture of the pulley, I’m doubtful that would work.
The extra space between the inner two and the outer sheave negates the use of the standard dual groove pulleys.
I’ve seen factory dual groove alternator pulleys that had the extra space, but don’t remember seeing any when looking for them in the aftermarket.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
I have a standard configuration radiator, along with the vertical thermostat housing orientation on my Explorer engine.
I’ll have to check with 904Bronco here, but I think it’s a standard Bronco upper hose, albeit split in the middle with a coupler so that the hose could be twisted.
Doug?
 

Slowleak

Bronco Guru
Joined
Sep 12, 2013
Messages
4,013
Loc.
Georgia
There might be another way too. A dual groove pulley on the alternator could utilize the existing belt, plus the front belt.
But looking at the original picture of the pulley, I’m doubtful that would work.

I think that picture shows a dual groove pulley on the alternator. The alternator can run as it is with a shorter belt around just the water-pump and crank. If the compressor can scoot forward it can run off the front groove. I expect that was the original reason for the 3 groove crank pulley. That’s a lot of speculating and armchair mechanizing on my part but it’s basically the setup I have.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
You're right. I forgot that I'd seen what I'd seen!
But I just noticed something else because you mentioned it. The existing belt is on the second sheave of the crank pulley, and the outer sheave of the alternator pulley. Meaning that with the addition of a belt that is just for the alternator, the problem of belt coverage is gone.
So just adding a short belt to the inner groove, just for the alternator, would take care of things.
Or so it looks from out here!

Paul
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Right you are again. I see the serrated inner side of the belt. Obviously the power steering that's just out of sight in the pic.
Makes it a candidate for one of the belt orientations I've been in favor of in some conditions for years. That's where the power steering belt also works with the alternator.
A long belt can work the power steering, and be the second belt for the alternator with much more pulley coverage.

Unless there are other roadblocks thrown up against it!

Paul
 
OP
OP
NJBronk

NJBronk

Contributor
Sr. Member
Joined
Oct 11, 2022
Messages
369
Hmm…. This is becoming quite the puzzle to solve…. I like the idea of a longer belt on the power steering loop that also goes to the alternator…

I also liked just looping the AC to the alternator and crank/water pump/alternator. That has the added benefit of getting the belt away from the radiator hose. But not sure if I’d be able to tighten the belt between the AC and alternator as it seems the alternator tightening might bring it closer to the AC condenser.

Or I just ditch the AC altogether.

Here are the pics I took before removing the belts (so that I could remember how they went), so I need to think a bit about how to configure…

Power steering and water pump:

IMG_0179.jpeg


Alternator, AC, and water pump:

IMG_0177.jpeg
 
Last edited:

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,114
Bottom pic, change to just crank and alterntor. Tons of belt wrap on the alternator and crank. Run a little belt from the back groove of the alternator to the back groove of the A/C. Clears the belt from the upper hose issue.
The only trick is tensioning the A/C belt. Either make a pivot on the A/C, or add an idler.

If I had A/C, no question I would keep it. My last project it was a requirement. No A/C, not interested. Didn't work when I got it, but had most of the parts and I made it work.
 
OP
OP
NJBronk

NJBronk

Contributor
Sr. Member
Joined
Oct 11, 2022
Messages
369
Bottom pic, change to just crank and alterntor. Tons of belt wrap on the alternator and crank. Run a little belt from the back groove of the alternator to the back groove of the A/C. Clears the belt from the upper hose issue.
The only trick is tensioning the A/C belt. Either make a pivot on the A/C, or add an idler.

If I had A/C, no question I would keep it. My last project it was a requirement. No A/C, not interested. Didn't work when I got it, but had most of the parts and I made it work.

How does one add an idler pulley? I never thought of that…
 
Top