Ok for using the standard distributor gear. Not ok for just starting and driving it however.
And as you will likely hear, modern flat-tappet cams and modern oils are not what they once were. Hence doubling down on the advice to use a specialized break-in oil, and/or a specialized break-in additive.
And for me, I keep using the specified oils for older flat-tappet engines. Many will say that once the cam is broken in, you can use any kind of oil you want after that. That might be true, or it might not. All I know is that I hear of more and more high-mileage engines that are wiping out their cams than I remember from years passed. So I'm sticking with high-zinc oils for general use. Even after the break-in procedure is done.
And speaking of which...
My personal version of the procedure will follow. I've kept to my old version as instructed by cam manufacturers back in the sixties, versus the modified versions that have come along in the meantime. Because I'm patient and have nothing better to do when I'm breaking in the cam, than to just break in the cam! I don't need to rush it.
So mine is the following:
1. Get everything and everyone ready for first startup. Verify as much as you can, so that the engine will fire right up instantly. Or as instantly as you can make it. Cranking the engine on a starter for longer, equals very bad. A quick start is very good.
The startup is why engine builders apply specialized lubricants to the camshaft during the build.
Prep should include putting fuel into the carburetor float bowls, if running carbureted. Or pumped up if using EFI.
If you're installing the intake manifold, verify the builder used "cam grease" or moly-lube or whatever they're calling the paste, or very sticky oil substance that is applied to the lobes prior to assembly. Then pour your chosen engine oil down the valley and through the return holes to get some more in the area of the camshaft.
1a. Prime the oil pump with a priming too. NOT by cranking the engine if you can avoid it.
1b. The previous steps may already have been done. But I mention them just in case, because you need to be ready to run.
1c. It pays to have helpers with eyes. If not, you'll be very busy for awhile! Pre-connect your timing light so you can verify what's going on.
1d. Needless to say, you absolutely must have all your gauges connected.
2. Fire the engine up! And immediately rev it to between 2500 and 3000 rpm and hold it there. This may very well be the hardest part to do, for any first-timer. But do it anyway!
2a. Remember,
NEVER let it idle down. No matter what you need to do, do not idle the engine. Best to stop the engine first, fix the issue, then fire it back up and run it up to the specified rpm.
3. Keep it at that range, but after the first minute or three, you can vary the rpm slightly up and down, but don't go below 2,000 for more than a few seconds, and stay above 2500 for as long as you can.
4. This period of adjustment, so to speak, should last for a full 30 minutes total. So make sure that the gas is in the tank and getting to the engine.
It does not have to be all at once, but that is better. If the engine gets too hot, you can turn it off to let it cool down. But don't idle it.
If you see a gas leak, shut it down to fix it. But don't let it idle.
If you see no oil pressure, shut it down (that should be obvious!). But don't let it idle.
Fix any issues, then fire it back up and bring it back to 2500-3000 immediately.
Seeing a pattern here?
This whole procedure revolves around not letting the engine below 2,000 rpm until at least 20 minutes of run-time have elapsed. I prefer 30 minutes, as I mentioned. But modern instructions often say 15 to 20 minutes and I've seen as low as 1500 rpm. And modern cams are often ruined in today's world. Is it due to the shorter duration, or lower rpm of the break-in? Or is it due to crappy materials? Or is it due to poor assembly? We may never know.
But I'm sticking with with 2500 and up, and 30 full minutes in my builds. So far so good, but I have not done one recently either. So I'm doing it my way, but also crossing my fingers!
Of course, I crossed my fingers every time (because I knew the consequences) since the sixties! But back then, I think crossing fingers yielded better results as well.
Good luck. Hopefully others here will chime in with recommendations, modifications, or whatever advice they can put forth.
Paul