• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Gas gauge issues

Bronk74

Sr. Member
Joined
Sep 1, 2004
Messages
414
Loc.
North Las Vegas
Hello ,
I ran out of gas for the last time. So I decided to fix the gas gauge issue.
Sitsuation:
I had the cluster rebuilt by classy gauges about 5 years ago. I put the dash board in about 3 years ago. I had found the old pig tail from old wiring harness so I decided to use it. Just noticed the power side is going to ground side for some odd reason. This is a stock pigtail???I will correct this.(wonder now if i blew up regulator due to wiring backwards) ####update#### Just found also the voltage regulator is not pulsing just shows a constant 10 volts DC on my dvom. Also old sending unit shows about 101.6 ohms any help appreciated
 
Last edited:
OP
OP
Bronk74

Bronk74

Sr. Member
Joined
Sep 1, 2004
Messages
414
Loc.
North Las Vegas
Hello ,
I ran out of gas for the last time. So I decided to fix the gas gauge issue.
Sitsuation:
I had the cluster rebuilt by classy gauges about 5 years ago. I put the dash board in about 3 years ago. I had found the old pig tail from old wiring harness so I decided to use it. Just noticed the power side is going to ground side for some odd reason. This is a stock pigtail???I will correct this.(wonder now if i blew up regulator due to wiring backwards) ####update#### Just found also the voltage regulator is not pulsing just shows a constant 10 volts DC on my dvom. Also old sending unit shows about 101.6 ohms any help appreciated
Update: I put gas into tank and the ohm reading went to 174 I think the sending unit is bad also
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
That’s what it sounds like to me too.
You need to measure voltage into the IVR (12 V) and out of the IVR (pulsing voltage) to see if that part is correct.
If it’s an original IVR, then it’s an electro, mechanical set of points that will pulse voltage. It’s easier to read on an old analog meter with a needle. If it’s a modern type, then you should see a steady 5v or 6v coming out.

And going to ground is what they do. It’s a variable resistance ground through the sending unit. So maybe that’s what you’re reading?
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Oh, and the resistance you should be seeing on the sending unit wires are 73 ohms empty, and 10 ohms full.
Once you go through enough of the gas again and can take the sending unit out, you should be able to measure it more accurately. While you run it through its range of motion by hand.
 
OP
OP
Bronk74

Bronk74

Sr. Member
Joined
Sep 1, 2004
Messages
414
Loc.
North Las Vegas
That’s what it sounds like to me too.
You need to measure voltage into the IVR (12 V) and out of the IVR (pulsing voltage) to see if that part is correct.
If it’s an original IVR, then it’s an electro, mechanical set of points that will pulse voltage. It’s easier to read on an old analog meter with a needle. If it’s a modern type, then you should see a steady 5v or 6v coming out.

And going to ground is what they do. It’s a variable resistance ground through the sending unit. So maybe that’s what you’re reading?
If I put a modern DVOM on the wires with power it shows 10volts DC no pulsing
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Interesting. Might be a modern style that’s misadjusted. We had a rash of those a couple of years ago.
Somewhere set as low as 2 V and the others as high as 10.
I sat there at my desk and adjusted every one to 5 to 6v.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Check the backside of yours and look for a very tiny rheostat type thingy. Should be able to turn it one way or the other to adjust it. Hopefully.
 
OP
OP
Bronk74

Bronk74

Sr. Member
Joined
Sep 1, 2004
Messages
414
Loc.
North Las Vegas
Check the backside of yours and look for a very tiny rheostat type thingy. Should be able to turn it one way or the other to adjust it. Hopefully.
Ok I ended up droping the whole cluster tried adjusting the voltage regulator apparently I could not adjust it lower only higher either and the voltage only changed by less than one volt and it was higher(10.87) Wondering if this is a sign the VR is bad? I want to know for sure before ordering paying $30 and shipping!
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Unless your testing criteria was wrong, I can’t imagine it’s anything but bad. They never put out 10 V.
Five to six is correct no matter what brand, model, or Ford application of this vintage.
 
Top