• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Running without top, windshield vibration

Flyfisen

Jr. Member
Joined
Jun 8, 2020
Messages
85
Ok question for the forum, first time this summer running my 68 without hardtop, only Bimini overhead I think from Tom’s. Like it a lot but getting a lot of windshield movement at freeway speeds. I have the cheaper version roll bar just over/behind seats and back to bed. Vinyl top attaches to top of windshield runs over head, over roll bar and attached to bottom of roll bar. Is there anyway to stabilize the top of the windshield like when running the factory hardtop?. Thanks
 

Speedrdr

Contributor
Legend in my own mind
Joined
Nov 27, 2017
Messages
2,028
Loc.
Paris, MS
Quick and dirty way is to take some flat stock and bolt one end to windshield and other end to rollbar (on each side). Many options exist, but this is probably the cheapest and easiest to do.
 

Soylent

Contributor
Sr. Member
Joined
May 4, 2016
Messages
690
Loc.
California
You could probably use that WH kit then extend from that adjuster to the roll bar with a steel cable. Like what is used on jeeps from front fender to windshield to deflect tree branches. Connect to roll bar with removable clamp.
 
OP
OP
F

Flyfisen

Jr. Member
Joined
Jun 8, 2020
Messages
85
I think the stainless cable idea will work, with turnbuckle adjustment. Now so long as I don’t hang myself letting dog in the back I’ll be good.
 

Master Chief

Contributor
Bronco Guru
Joined
Nov 24, 2006
Messages
1,312

Attachments

  • IMG_1106.png
    IMG_1106.png
    354.5 KB · Views: 123

Beau Nugget

Jr. Member
Joined
Aug 20, 2022
Messages
132
Loc.
NE Kansas
That’s what I have too. It works well, but the bikini top has to stretch over the adjustment rings and doesn’t fit snug on the rollbar. Not a huge deal, but I wonder how long until holes are worn into the top by the rings on the rollbar. Obviously not a concern if you don’t have a bikini top
 

Speedrdr

Contributor
Legend in my own mind
Joined
Nov 27, 2017
Messages
2,028
Loc.
Paris, MS
That’s what I have too. It works well, but the bikini top has to stretch over the adjustment rings and doesn’t fit snug on the rollbar. Not a huge deal, but I wonder how long until holes are worn into the top by the rings on the rollbar. Obviously not a concern if you don’t have a bikini top

Short hijack…could you take some foam pipe insulation and run from the connection point at windshield to over and a little past the rings? That would give some padding and protection to the bikini top
 

Beau Nugget

Jr. Member
Joined
Aug 20, 2022
Messages
132
Loc.
NE Kansas
Short hijack…could you take some foam pipe insulation and run from the connection point at windshield to over and a little past the rings? That would give some padding and protection to the bikini top
The problem area isn’t the steel rod that connects the windshield to the rollbar. It’s the two big donut shaped pieces that go around the rollbar to which the steel rods mount. These donut shaped pieces stick up about 1/2“ to 3/4”, and the top has to stretch over them instead of just stretching over the whole length of the rollbar like it would if they weren’t mounted to it. I got a piece of rollbar padding to fit between the donuts, but the padding isn’t thick enough, so it doesn’t do much good. I’ve resigned myself to just replacing the top if holes get worn into it. They aren’t that expensive
 
Top