• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

First Bumper build

Grey owl

Contributor
Sr. Member
Joined
Nov 19, 2024
Messages
398
20251112_164909.jpg

First try at bumper build with 12000lb winch. Just tacking and final fitting. 1/4 steel plate laser cut. Will post finished pics when done.
 

Attachments

  • 20251112_164857.jpg
    20251112_164857.jpg
    224.8 KB · Views: 148
  • 20251112_164700.jpg
    20251112_164700.jpg
    160.1 KB · Views: 134
  • 20251112_164712.jpg
    20251112_164712.jpg
    134.1 KB · Views: 172

jeffncs

Contributor
Bronco Guru
Joined
May 4, 2004
Messages
1,898
Loc.
Raleigh, NC
Thats a serious bumper!! Looks great!!

Bit of advice - make sure you can access the winch bolts to fasten / remove along with the battery cables before gluing it together permanently.
 

Apogee

Contributor
Bronco Guru
Joined
Nov 26, 2005
Messages
6,348
Loc.
Tangent, OR
That looks stout! Did you design it in CAD first, and if so, what package did you use? What's the final weight of the bumper going to be without the winch?
 
OP
OP
Grey owl

Grey owl

Contributor
Sr. Member
Joined
Nov 19, 2024
Messages
398
That looks stout! Did you design it in CAD first, and if so, what package did you use? What's the final weight of the bumper going to be without the winch?
Its.pretty solid weighs about 75 lbs without winch. I made patterns and took them to the metal shop where the measurements and final design work were done on computer. The 3/4 tow hook were cut with water jet the 1/4 was cut with laser.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,111
You can take that relay pack off the top of the winch and move it under the hood. Just need to make a new set of cables for the extended length. That will clean it up even more.

How is the frame attachment? What I did was drill through the frame and sleeve, pulled the bumper off and tapped the hole for a bolt, drilled the frame out to the bolt size. Did that in several spots. That way the shear was spread across many small fasteners and not just a couple of large ones into fairly thin frame metal. If it was going to pull out of the frame, it was going to take the frame with it.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,111
I'm not very well versed in steel. But to me 1/4 inch plate seems massively overkill for a bumper.
Not when a winch is involved. If it gets anywhere near its rated capacity on a pull, ¼" plate alone will still bend. If you look at the mounting channel that you can get with a winch, the front and rear edges of the plate are turned up. This is to stiffen the plate on winching loads as a flat plate alone isn't strong enough. I hope there is something like that planned for the bottom dropout winch mount that is planned.
 

nvrstuk

Contributor
Just a Bronco driver for over 50 yrs!
Joined
Jul 31, 2001
Messages
10,620
Loc.
PNW
Looks stout! Stout is what you want when winching and jerking to the side if you can't use your winch (more common than most think).

Agree with broncobowsher on multiple frame mounts. Don't rely on the stock bumper bolt holes. Extend those frame attachment points in as far as it will go so you can add more bolts to attach it to spread the load. Slow steady pull isn't that much of a big deal. Hard jerk from a "big stick" can put a lot of strain on stock mounting bolts.

Just sharing what I've seen so many times.... stout bumpers but the attachment points don't work.
 
OP
OP
Grey owl

Grey owl

Contributor
Sr. Member
Joined
Nov 19, 2024
Messages
398
I'm not very well versed in steel. But to me 1/4 inch plate seems massively overkill for a bumper.
Not really when you have a 12000 lb winch attached to it. That much winch power can twist up a weak bumper and cause safety issues. Plus the tow hooks on the bumper do not pull from the center sl again build with strenght to prevent problems.
 
OP
OP
Grey owl

Grey owl

Contributor
Sr. Member
Joined
Nov 19, 2024
Messages
398
Looks stout! Stout is what you want when winching and jerking to the side if you can't use your winch (more common than most think).

Agree with broncobowsher on multiple frame mounts. Don't rely on the stock bumper bolt holes. Extend those frame attachment points in as far as it will go so you can add more bolts to attach it to spread the load. Slow steady pull isn't that much of a big deal. Hard jerk from a "big stick" can put a lot of strain on stock mounting bolts.

Just sharing what I've seen so many times.... stout bumpers but the attachment points don't work.
The frame ends have been reinforced with 1/4 " steel all 4 sides. Not taking any chances.
 
OP
OP
Grey owl

Grey owl

Contributor
Sr. Member
Joined
Nov 19, 2024
Messages
398
Not when a winch is involved. If it gets anywhere near its rated capacity on a pull, ¼"es plate alone will still bend. If you look at the mounting channel that you can get with a winch, the front and rear edges of the plate are turned up. This is to stiffen the plate on winching loads as a flat plate alone isn't strong enough. I hope there is something like that planned for the bottom dropout winch mount that is planned.
Yes , the bottom has an additional.1/4" added to the area the winch mounts. There are also 1/4" bulkheads to help eliminate any twisting and further distribute stress energy through out the bumper. The two main bulkheads are 3/4". There should adequate energy distribution.
 
OP
OP
Grey owl

Grey owl

Contributor
Sr. Member
Joined
Nov 19, 2024
Messages
398
The frame ends have been reinforced with 1/4 " steel all 4 sides. Not taking any chances.
The top bolts are 1/2 grade 8 in the original location. The bottom have three 1/2 grade 8 bolts on each side.
I am not a fan of long light bars. The system chosen allows for two 12" lights on either side of the solonoid housing plus four 4" flush mounted in the angle to provide adequate perriffial coverage. So six lights on one switch using two relays to protect switch.
 
OP
OP
Grey owl

Grey owl

Contributor
Sr. Member
Joined
Nov 19, 2024
Messages
398
As an added bonus each person can have lunch next to the winch :cool:

Just joking, looks well built!
Actually there isn't much room, the center area the widest point only extends out 6 1/2 " just one inch more than the width of the compact winch. The back of the winch is just under the grill. The solonoid box clearance is 3/4". The design was to keep the amount protruding to an absolute minimum. The design of this new generation of compact winches eliminates those big bulky winch bumpers.
 

Steve83

Bronco Guru
Joined
Jul 16, 2003
Messages
9,360
Loc.
Memphis, TN, USA, Earth, Milky Way
But to me 1/4 inch plate seems massively overkill for a bumper.
It's slightly thicker than necessary for the outboard sections, but at the winch mount, it can make up for a weak design.
...¼" plate alone will still bend.
Only if it's a VERY weak design, and the Bronco is VERY stuck (or anchored).
...in several spots. That way the shear was spread across many small fasteners...
None of the fasteners should be in shear - they should ONLY be in tension, applying compression to the frame so that the clamping force creates friction over a large area. That's the best way to distribute the load onto the thin frame.
...build with strenght to prevent problems.
But building with WEIGHT creates problems, and weight (thickness) does not equal strength. So the design needs to be as light as possible - especially on a vehicle with such a thin-walled frame as an eB. If you actually load up the 0.25" steel of the bumper, you'll just rip the 0.120" frame apart. If not at the ends, somewhere else.
The two main bulkheads are 3/4".
IDK what you mean by "bulkhead", but 0.75" is gargantuan overkill/overweight.
 
Top