- Joined
- Nov 19, 2024
- Messages
- 398
Its.pretty solid weighs about 75 lbs without winch. I made patterns and took them to the metal shop where the measurements and final design work were done on computer. The 3/4 tow hook were cut with water jet the 1/4 was cut with laser.That looks stout! Did you design it in CAD first, and if so, what package did you use? What's the final weight of the bumper going to be without the winch?
Not when a winch is involved. If it gets anywhere near its rated capacity on a pull, ¼" plate alone will still bend. If you look at the mounting channel that you can get with a winch, the front and rear edges of the plate are turned up. This is to stiffen the plate on winching loads as a flat plate alone isn't strong enough. I hope there is something like that planned for the bottom dropout winch mount that is planned.I'm not very well versed in steel. But to me 1/4 inch plate seems massively overkill for a bumper.
Not really when you have a 12000 lb winch attached to it. That much winch power can twist up a weak bumper and cause safety issues. Plus the tow hooks on the bumper do not pull from the center sl again build with strenght to prevent problems.I'm not very well versed in steel. But to me 1/4 inch plate seems massively overkill for a bumper.
The frame ends have been reinforced with 1/4 " steel all 4 sides. Not taking any chances.Looks stout! Stout is what you want when winching and jerking to the side if you can't use your winch (more common than most think).
Agree with broncobowsher on multiple frame mounts. Don't rely on the stock bumper bolt holes. Extend those frame attachment points in as far as it will go so you can add more bolts to attach it to spread the load. Slow steady pull isn't that much of a big deal. Hard jerk from a "big stick" can put a lot of strain on stock mounting bolts.
Just sharing what I've seen so many times.... stout bumpers but the attachment points don't work.
Yes , the bottom has an additional.1/4" added to the area the winch mounts. There are also 1/4" bulkheads to help eliminate any twisting and further distribute stress energy through out the bumper. The two main bulkheads are 3/4". There should adequate energy distribution.Not when a winch is involved. If it gets anywhere near its rated capacity on a pull, ¼"es plate alone will still bend. If you look at the mounting channel that you can get with a winch, the front and rear edges of the plate are turned up. This is to stiffen the plate on winching loads as a flat plate alone isn't strong enough. I hope there is something like that planned for the bottom dropout winch mount that is planned.
The top bolts are 1/2 grade 8 in the original location. The bottom have three 1/2 grade 8 bolts on each side.The frame ends have been reinforced with 1/4 " steel all 4 sides. Not taking any chances.
Actually there isn't much room, the center area the widest point only extends out 6 1/2 " just one inch more than the width of the compact winch. The back of the winch is just under the grill. The solonoid box clearance is 3/4". The design was to keep the amount protruding to an absolute minimum. The design of this new generation of compact winches eliminates those big bulky winch bumpers.As an added bonus each person can have lunch next to the winch
Just joking, looks well built!
It's slightly thicker than necessary for the outboard sections, but at the winch mount, it can make up for a weak design.But to me 1/4 inch plate seems massively overkill for a bumper.
Only if it's a VERY weak design, and the Bronco is VERY stuck (or anchored)....¼" plate alone will still bend.
None of the fasteners should be in shear - they should ONLY be in tension, applying compression to the frame so that the clamping force creates friction over a large area. That's the best way to distribute the load onto the thin frame....in several spots. That way the shear was spread across many small fasteners...
But building with WEIGHT creates problems, and weight (thickness) does not equal strength. So the design needs to be as light as possible - especially on a vehicle with such a thin-walled frame as an eB. If you actually load up the 0.25" steel of the bumper, you'll just rip the 0.120" frame apart. If not at the ends, somewhere else....build with strenght to prevent problems.
IDK what you mean by "bulkhead", but 0.75" is gargantuan overkill/overweight.The two main bulkheads are 3/4".
Where there was one 1/2 grade 5 bolt now there is three 1/2 grade 8 boltsstout, big winch, make sure frame mount can take it![]()
Yeah bigmuddy I think you're talking about my front bumper.As an added bonus each person can have lunch next to the winch
Just joking, looks well built!






