• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Slight Shackle Lean

jdowns67

Owner since 2001
Joined
Feb 27, 2010
Messages
62
Loc.
Wilmington, NC
Anyone else notice their shackles lean slightly inward toward the middle of the vehicle? Both are about the same. I'm wondering if 55 years of absorbing road shock has eventually bent the mounts at the bottom in slightly. Only noticing since I installed all new suspension. Bronco is not leaning.
1000017770.jpg
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Probably multiple possibilities.
Including the one you mentioned, of years of weight on them, could also be uneven wear in the holes, or even the fact that they were made that way.
Could’ve been called for on purpose, or just nature of the beast in the imperfect world back then.
You didn’t happen to notice whether the holes were still perfectly round, or ovalized, or not. Did you?
When I disassembled my 71 rear springs, for the first time, my holes were already well worn to the point of needing some extra TLC.
That was roughly 81 or 82, and not much more than 100,000 miles on the truck.
No telling what they could’ve gone through in the ensuing 50 years! :)
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
But I’m happy to subscribe to your thread, because I’m interested to see what others find.
 

MarsChariot

Contributor
Planetary Offroader
Joined
Oct 12, 2004
Messages
2,605
Loc.
Albuquerque, New Mexico
I took a quick look at my '76 and it looked about the same on the driver's side. However, The passenger's side looks horizontal. Given that these are not precision chassis for all sorts or reasons, can you confirm that the passenger side is also angled about the same amount? I am about to install the same shackles, so I will keep my eyes on this as I go forward.
 
OP
OP
jdowns67

jdowns67

Owner since 2001
Joined
Feb 27, 2010
Messages
62
Loc.
Wilmington, NC
I took a quick look at my '76 and it looked about the same on the driver's side. However, The passenger's side looks horizontal. Given that these are not precision chassis for all sorts or reasons, can you confirm that the passenger side is also angled about the same amount? I am about to install the same shackles, so I will keep my eyes on this as I go forward.
One of mine is about 1.5 degrees inward and the other about 1.7 inward.
 
OP
OP
jdowns67

jdowns67

Owner since 2001
Joined
Feb 27, 2010
Messages
62
Loc.
Wilmington, NC
Probably multiple possibilities.
Including the one you mentioned, of years of weight on them, could also be uneven wear in the holes, or even the fact that they were made that way.
Could’ve been called for on purpose, or just nature of the beast in the imperfect world back then.
You didn’t happen to notice whether the holes were still perfectly round, or ovalized, or not. Did you?
When I disassembled my 71 rear springs, for the first time, my holes were already well worn to the point of needing some extra TLC.
That was roughly 81 or 82, and not much more than 100,000 miles on the truck.
No telling what they could’ve gone through in the ensuing 50 years! :)
Holes were not worn. I am either doing to just drive it or I may elongate the hole slightly down on the outside and then weld it back up. I think you saw my other post where I made some steel reinforcement washers and welded them on the outside of the front hangers, then welded up the old holes because they were worn out on the inside and driled back through. Can do the same principal on the back. Or I may just drive it...lol
 

toddz69

Sponsor/Vendor
Bronco Guru
Joined
Nov 28, 2001
Messages
11,222
Yours look pretty good compared to mine - I'll need to measure mine at some point. As long as my bolt head isn't rubbing the frame, I don't worry about it. I think I've got some slop in my lower bushings that helps mine lean more.

Todd Z.
 

Oldtimer

Contributor
Jr. Member with Sr. moments
Joined
Feb 4, 2005
Messages
1,801
Loc.
Sunnyvale, CA
🤔 Half century old frame, with assembly line welded forged bracket, that has a punched set of holes, locating a bolt, that supports a couple of bushings, in a stamped formed welded bracket with punched holes, locating a second bolt, that supports two more bushings, pressed into a formed piece of spring steel, that most likely has a twist in it, that is bolted to a spring perch that is welded to an axle . . . . measures 1.45 degrees from the level (??) floor.
 
Last edited:
OP
OP
jdowns67

jdowns67

Owner since 2001
Joined
Feb 27, 2010
Messages
62
Loc.
Wilmington, NC
🤔 Half century old frame, with assembly line welded forged bracket, that has a punched set of holes, locating a bolt, that supports a couple of bushings, in a stamped formed welded bracket with punched holes, locating a second bolt, that supports two more bushings, pressed into a formed piece of spring steel, that most likely has a twist in it, that is bolted to a spring perch that is welded to an axle . . . . measures 1.45 degrees from the level (??) floor.
I admit, I'm over analyzing... lol
 
Top