• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Dana 44 upper balljoint torque

chuddy

Full Member
Joined
Sep 28, 2020
Messages
347
I realize there are gobs of threads about getting the upper balljoint torqued correctly, but for some reason I just can't seem to get it quite right. When I set the spacer to 40 ft/lb and tighten the big top nut to 100 ft/lb, the actually ball joint itself will twist when I move the knuckle back forth....assuming that is NOT the correct way to do it. If I tighten the spacer MORE than 40 ft/lb, the balljoint stops twisting but the pull force on the knuckle is now more than the spec of 26 pounds. Anyone else run into this?
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Do you mean that the outer body of the ball joint is spinning inside the knuckle?
If so, I’m not sure you’re gonna get there from here. That junction should be so tight that the only thing moving would be the ball/stud.

On these installs, you can always try setting the sleeve to a different torque. For example, 35 pounds. I’ve used even less to get the proper settings. But these days, seems to be a crapshoot.
There was a really good discussion about it just a week or two ago with lots of detail on how just how the system works. But if your ball joint’s outer body is spinning in the knuckle casting, there’s something else going on.
 
OP
OP
C

chuddy

Full Member
Joined
Sep 28, 2020
Messages
347
It's the ball/stud that spinning. Outer ballpoint body is tight in the C.

Sent from my SM-S901U using Tapatalk
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
OK, good.
Did you wipe the inner tapers with a fingertip or rag to make sure they were clean and free of any grit of any kind that might interfere with the seating of the male and female halves together?
If the holes are clean, and not damaged/worn, then I don’t see a scenario where 100 pounds could allow that to turn when you’re moving the knuckles. Other than a damaged taper.

They usually spin when you’re tightening the nut, though. If that’s what you’re experiencing, then press upward on the knuckle with a jack if you aren’t already and see if that helps.
That’s usually only needed for the lower ball joint, but it can’t hurt to try in this case.

And rather than experimenting with less torque on the sleeve, perhaps try 45 pounds. At this point you’re wrestling with an unknown, so might as well throw some different numbers in there to see what comes out of the mix.

James is probably awake by now. Maybe he’ll see this thread with his morning coffee and throw in with his experiences.
 
OP
OP
C

chuddy

Full Member
Joined
Sep 28, 2020
Messages
347
Thanks, it's strange because the stud/ball does NOT spin when I tighten the nut down. It only turns when I turn the knuckle. If I REALLY tighten the nut, the stud/ball/nut don't spin when I turn the knuckle, but of course it's harder to move (more than 26 pounds of force).
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
The stud and it’s ball are supposed to turn when you turn the knuckle. That’s the actual pivot point.
That’s why the ball joints are greaseable sometimes. And when they are not, they are already packed with grease.
The grease lets the ball rotate in the socket, both upper and lower, so that the knuckle can turn.
The taper locks the stud and sleeve together, making the ball the only thing in the entire assembly that can rotate in its socket.

Go back to initial settings and see if you get the under 26 turning torque.
Remember, it’s not 26 exactly. It’s less than 26.
Should not be loose and sloppy, but it should not be tighter than 26.
 
OP
OP
C

chuddy

Full Member
Joined
Sep 28, 2020
Messages
347
The stud and it’s ball are supposed to turn when you turn the knuckle. That’s the actual pivot point.
That’s why the ball joints are greaseable sometimes. And when they are not, they are already packed with grease.
The grease lets the ball rotate in the socket, both upper and lower, so that the knuckle can turn.
The taper locks the stud and sleeve together, making the ball the only thing in the entire assembly that can rotate in its socket.

Go back to initial settings and see if you get the under 26 turning torque.
Remember, it’s not 26 exactly. It’s less than 26.
Should not be loose and sloppy, but it should not be tighter than 26.

Wait, now I'm really confused. I assumed the stud would be "fixed" within the taper of the knuckle when it's installed properly, meaning it would not turn when turning the knuckle. When moving the knuckle back and forth, I had assumed that the body of the balljoint (that's pressed into the knuckle) would turn around the ball, meaning the stud would remain fixed in relation to the C. Otherwise, the big nut would ALSO need to turn because it's cotter key'd in.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
OK, I misunderstood what you were saying.
Yes, the stud is fixed in the tapered hole. I thought you were saying that the stud, which is fixed to the ball of course, was rotating in the body of the ball joint.
Not that the stud was rotating in the taper.

Sorry for creating confusion where there was none.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Any chance of posting up a video of exactly what you're seeing?

Paul
 
Top