• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Vertical half cab bulkhead?

thegreatjustino

Contributor
Red Head Grease Monkey
Joined
Jan 23, 2002
Messages
16,291
Loc.
Stockton, CA
I don't have any better pictures than what I've added below, but this '73 had a custom sliding window in the factory half cab along with a vertical bulkhead. The bulkhead touched the front edge of the rear wheel wells. By making it vertical, there was around a foot of cargo room behind the seats where the guy I bought the Bronco from had speaker boxes. Without the speaker boxes, you might have been able to squeeze a bag of golf clubs back there. It wasn't a ton of room, but clearly more than the stock angled bulkhead.

I sold this Bronco probably a decade ago now, so can't get any further pictures.
 

Attachments

  • IMG_3931.JPG
    IMG_3931.JPG
    163.5 KB · Views: 189
  • IMG_3932.JPG
    IMG_3932.JPG
    177.7 KB · Views: 168
  • IMG_3413.JPG
    IMG_3413.JPG
    168.9 KB · Views: 155
OP
OP
Stevenb

Stevenb

Contributor
New Member
Joined
Jun 24, 2007
Messages
39
Loc.
Spokane Valley, WA
Has anyone ever built of found a vertical and not angled half cab bulkhead? I want to get one and thought I’d search before I build one. I really want the space behind the seats. Thanks for the help!
I built a vertical bulkhead if anyone ever wants to replicate it. It was pretty simple and clean
 

JSBX

Contributor
Sr. Member
Joined
Mar 10, 2010
Messages
652
I have a vertical bulkhead in mine. It was built by the body shop that did the frame off paint job on my 74. It was built in 3 pieces to make it easier to install and remove. It may be a few days before I can get pictures and post. It does give almost a foot of room behind the seat. It lands on the ridges of the bed floor and makes it a problem to seal off but is doable. I used 2x2 angle iron and bolted it to the floor with a gasket on the bottom of the angle iron. This sealed the top of the ridges but still left a gap on the bottom of the ridges. I used water resistant spray foam insulation to fill in the gaps under the angel iron. Also used a gasket between the angle iron and bulkhead and bolted it to the angle iron. I tested it with a water hose with just a couple of drops getting through on the bed floor. I have not sealed the sides yet but will use a polyurethane sealant for that. The angle iron is on the inside of the cab because like thegreatjustino said, the bulkhead does contact the front edge of the rear wheel wells. The sides were cut to fit the contour of the inside of the bed. Will post pictures as soon as I can.
 

Speedrdr

Contributor
Legend in my own mind
Joined
Nov 27, 2017
Messages
2,028
Loc.
Paris, MS
@Stevenb and @JSBX, if y’all don’t mind and it’s not too much trouble, could y’all post some pics of how it looks/how it was done? I have a new bulkhead, but it’s too much work to get it to fit right in my ‘77 that is gonna become a 1/2 cab. TIA
 
OP
OP
Stevenb

Stevenb

Contributor
New Member
Joined
Jun 24, 2007
Messages
39
Loc.
Spokane Valley, WA
I am trying to get photos on here but I don’t know if you can do it from a phone. I have some photos on my Instagram if you are on there. If not I’ll try to use my laptop when I get home.
 
OP
OP
Stevenb

Stevenb

Contributor
New Member
Joined
Jun 24, 2007
Messages
39
Loc.
Spokane Valley, WA
@Stevenb and @JSBX, if y’all don’t mind and it’s not too much trouble, could y’all post some pics of how it looks/how it was done? I have a new bulkhead, but it’s too much work to get it to fit right in my ‘77 that is gonna become a 1/2 cab. TIA


I am trying to get photos on here but I don’t know if you can do it from a phone. I have some photos on my Instagram if you are on there. If not I’ll try to use my laptop when I get home.
 
OP
OP
Stevenb

Stevenb

Contributor
New Member
Joined
Jun 24, 2007
Messages
39
Loc.
Spokane Valley, WA
I have the drawing that I made for what I had bent up at a local shop. I had to do the trimming and fitting, and then mounted it with steel robots everywhere so it was easy to put in and take out. So far it’s perfect. I am going to try to raptor line it over Christmas break. Once I finish my wiring anyway. I am going to either 3d print fillers for the bed grooves or cut some thick rubber mat, and then use some seam sealer or weatherstripping adhesive to seal them to the floor. I may add a small door to the bottom, but I may just get the sliding window from Tom’s.
 

Speedrdr

Contributor
Legend in my own mind
Joined
Nov 27, 2017
Messages
2,028
Loc.
Paris, MS
I am trying to get photos on here but I don’t know if you can do it from a phone. I have some photos on my Instagram if you are on there. If not I’ll try to use my laptop when I get home.

Photos can be done from phone. To upload pics, the easiest way is to become a contributor for the paltry sum of $12/year. Instructions are in the initial posts in Bronco Chat.

My instagram is grind_hilda.
 

JSBX

Contributor
Sr. Member
Joined
Mar 10, 2010
Messages
652
Here are some pictures of mine. Not the best pictures, old phone and cloudy day here.
 

Attachments

  • 20251223_114947.jpg
    20251223_114947.jpg
    134.8 KB · Views: 126
  • 20251223_114800.jpg
    20251223_114800.jpg
    238.7 KB · Views: 124
  • 20251223_114717.jpg
    20251223_114717.jpg
    144.8 KB · Views: 105
  • 20251223_114627.jpg
    20251223_114627.jpg
    224.8 KB · Views: 121
  • 20251223_114602.jpg
    20251223_114602.jpg
    160.3 KB · Views: 120
  • 20251223_114536.jpg
    20251223_114536.jpg
    170.9 KB · Views: 118
  • 20251223_114658.jpg
    20251223_114658.jpg
    256.1 KB · Views: 100
  • 20251223_114602.jpg
    20251223_114602.jpg
    160.3 KB · Views: 112
  • 20251223_114614.mp4
    4.9 MB
Top