• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Search results

  1. B

    75 Front Coil Spring Comparison

    I agree try what you have. Most likely they will be fine. Many times your shocks may be the cause of a harsher ride more so than the springs. Good shocks can make a world of difference.
  2. B

    Drive-train Advice?

    Most of the time you'll hear the gears howling or making noise when there is a issue in the axle. For the most part the differential and gears can last a very long time with good maintenance. Also you will tend to feel play In the drivetrain when things get worn. I've got over 350K on the rear...
  3. B

    205 idler shaft, shims, side play in case

    Yeah you might need to install some thrust washers between the bearings and case. A good bearing shop can get you the size you need. You could also use machine bushings some hardware stores carry them not sure on sizes available but I'm sure they could be ordered in the size needed. Id probably...
  4. B

    Braking Issues

    Id get all your specs together there are calculators and guidelines on caliper piston area vs MC piston size. Just a quick look and Id say 1 1/8" is to big. 1in or 15/16" may be what you need but I don't know what your total piston area is. but going down to a 1in MC will give about another 300...
  5. B

    Drop trac bar bracket needed? Pulls to right with heavy braking

    The other issue I see is you have a adjustable trac bar but the drag link is not adjustable. While the drop pitman arm takes care of some of the adjustment the drag link would need. It probably over adjusted and that may also be a cause of the pulling. In any case I prefer to have a adjustable...
  6. B

    68' with straight 6 - looking to change engine - advice?

    Welcome. A few people have done a 300 swap I don't recall them having to cut the hood. you might do a search see what comes up. Whoever installed the engine just threw it in and didn't care about the hood clearance, Probably still has the stock bronco 6cyl tranny. The 300 is a good engine if you...
  7. B

    Improving reliability

    Kinda sounds like you've got the mechanical side more or less covered. Wiring would be a good idea if that's where your issues are. Otherwise like any vehicle things do happen now and then theres no real way to prevent other than regular maintenance and inspection to catch the little things that...
  8. B

    Ax15/NV3550

    Here's a link that may help you. https://www.novak-adapt.com/ both trannys are all aluminum and I believe the adapter kits fit both so it may not matter which one it is. either way $200 is a good deal if its either tranny in good shape. It may be a AX15 as the I didn't see the PN given under a...
  9. B

    Explorer Swap with 5.8 block

    1994 up 5.8's were roller blocks but they didn't get roller cams until 96ish. it was the same as the explorer cam. So basically your looking for vans and pickups from 94-97 maybe 98. The only way to verify the year of the block is look for the casting number you have to remove the starter to...
  10. B

    205 idler shaft, shims, side play in case

    The play is only measured when the nut is tightened. How are you determining the .002 play? Does the case appear to have any wear if so that could be the cause of your excessive play with the nut tight. In that case shims outboard of the bearings may help. Whatever side has wear is where Id put...
  11. B

    Small bearing 9"

    Id put the ARB on the back burner and just get you a big bearing housing first you can either get a new one or used. Or a used fullsized housing and have it shortened although then your at about what a new housing would cost. But you would have the brake setup so it would put you ahead. You...
  12. B

    4-Speed Floor Shift - Front Channel Chop

    Yep forward channel didn't need to be cut. With a body lift you should need even less of a hole. That hole is almost big enough to install the tranny from the side. I ran a toploader for years back when it was pretty much the only option out there. For the street it was a good transmission but...
  13. B

    2.3 ecoboost

    Well swap one in and let us know how it is. That's the only real way for you to know. I'm not real sure why you think most of the 5.0's swapped into broncos wont pass emissions. I think most will even if they are missing some of the equipment they came with stock. Even a lot of built engines...
  14. B

    Thoughts on going Coyote?

    I think most people swap them because of the HP numbers and to be different.. Yes properly setup it can be a good setup. But for me the added complication of the engine ie, variable valve timing, cam phasers ect. and electronics plus the size of the thing. is not worth it. Most of the charts Ive...
  15. B

    Explore stock oil pan

    Unless your into real hardcore rock crawling I wouldn't worry much about a rock hitting the oil pan. Usually your front driveshaft will be the item that takes the abuse. Of course anything can happen.
  16. B

    Anybody cut an Explorer Waterpump?

    Water pump seals are pretty tough mechanical type seal usually stainless steel and graphite pretty tough to hurt unless you get the shaft red hot.
  17. B

    Power brakes vs. disc

    I vote for going to discs as well. It was one of the best upgrades I ever did. I drove my bronco for many years with drums and the famous drum brake pull always seemed to show up when you really needed to stop. But since you have new drums there's nothing wrong with going to a power booster now...
  18. B

    Build decisions-stock or resto-mod??

    The only reason to go stock is if its what you want. resto mod is what most people have anyhow and as long as you don't go overboard there is no real value lost most people will want the items your considering anyhow. Sounds like you have a decent build planned out.
  19. B

    Walmart SCoooOOrrrRReee

    That's been out a couple of years. So none has posted lately on it. You could also find just the skyjacker bronco in that set by itself.
  20. B

    Transmission & transfer case question

    Also keep in mind that you'll probably need to regear the axles to make full use of the 5 speed. Few transmission swaps are cheap when all said and done but usually the money you do have to spend is worth the end result
Top