• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Search results

  1. B

    Suspension question

    I think you could come close to doing it with airbags. biggest issue is you wont be able to go down but 7 in in the front and 6 in the rear when fully deflated as that's about the measurements of stock height from top of axle tube to bottom of frame. You may consider modifying the pass side...
  2. B

    Original color - value opinion

    All matters to the buyer and what they are looking at. Original paint could bring the most as was said if the bronco is pretty much stock. Repaint well that can detract for a purist but nice paint does help sell. In the end are you building to drive it or to sell it? If your driving it with no...
  3. B

    Tucson Bronco Project Day - October 7th - Open Invite

    I'm still planning on making over. Just not sure I'll bring a bronco this go around. While I have many projects to get done on my broncos I'm nowhere near ready to do the work. I need to buckle down and get a engine built. I think this wrench part may help motivate me. Looking forward to meeting...
  4. B

    Alternator Question

    There were stock 100 amp 1g alternators but they had larger cases and I'm not sure how well they would fit in a bronco along with the wiring issue if you want to keep the ammeter. I believe they were in lincolns and possibly trucks with camper special pacakges. There were also kits that you...
  5. B

    light under key switch

    Its supposed to light up during start up then go off but may not always come on that's just a self test. As was said its most likely the switch on the Hblock down on the drivers side frame rail just ahead of the MC. there should be purple wires going to it. You may still have air in one side of...
  6. B

    Rear brakes dragging over time

    Back pressure on the return line could have been causing the booster to not retract all the way. With no place to go the fluid will move whatever is easiest to move in the system. My concern would be what was the material in your filter. especially if enough to block it up. Was it black, whitish...
  7. B

    Help with rear brake decision

    Id post up on the classifieds on what your wanting someone probably has the parts laying around that you need for cheap. Or search thru some one may be sell what you need. Id say your bearing retainer flange is the stock style as my 73 big bearings retainers are also rectangle. and the flange...
  8. B

    Stock height suspension thoughts

    New springs and such may be better than stock but many times most of the ride quality is in the shocks. Good shocks can make a difference even on old stock suspensions. So if your not set on new springs just yet you may want to research shocks and try them out first
  9. B

    Tucson Bronco Project Day - October 7th - Open Invite

    While no longer in Tucson I'll try and make it. Its always good to get together with some bronco brothers. Not sure if I'll bring a bronco as my 73 is a little sick. Its due for a new engine and my 71 is just not as roadworthy as I would like for the 2 hour trip. But well see the 73 might make...
  10. B

    Frustrating new problem... Help please!

    Check for a vacuum leak. It can cause high idle speed and may cause the mixture screws seem not to have any effect.
  11. B

    Radius Arm - Cotter Pin hole

    No the preload is just for the bushing compression. Lean typically comes from the C bushings.
  12. B

    Possible high temp issues when stopped

    X2 On top of that do you know if your gauge is accurate could be a little off and your not that hot. Also if you let it idle and when it gets to 200 degrees try upping the idle speed a little most likely the temp will come down. You may need a different fan. Flex fans do wear out so to speak as...
  13. B

    NP435 front bearing retainer too big?

    The dodge cases are different as far as bellhousing bolt pattern, input shaft is much longer than ford or gm versions and output shaft spline count is 23. Usually the dodge and gm versions had a higher 1st gear as well something like 4.90. Bigger trucks that had the NP435 usually had larger dia...
  14. B

    Carb question. BRONCO ALMOST DONE!

    I agree sounds like you need some adjustments. This link may help you run through the adjustments...
  15. B

    302 Idles Fine in P but Runs Rough and Stalls When in Gear

    78 heads should be pedestal rockers no adjustment. You might try checking the torque on your intake bolts. Some times a few heat cycles with cause the gaskets to shrink and leak. I think your idle speed needs to be set higher probably needs to be around 800 in park 650 in drive.
  16. B

    Engine Guru's

    Many times thermostats wont close all the way might be more of a issue with highflow pumps and high flow tstats but Ive had the issue with standard pumps and both standard and hiflow tstats the temp would rarely get close to the thermostat rated opening point. When I tested the tstat I found it...
  17. B

    steering box id help

    Sounds like its at least a saginaw box as the number you listed is usually whats on the aluminum top cover. Does it look like a stock bronco type power steering box? If you don't know what they look like check out the vendors sites most have pictures of stock and other common conversion boxes...
  18. B

    Fender Flares

    look at the links in post 2
  19. B

    Test Running Engine

    AC not hooked up no problem the compressor will not turn unless you power up the clutch. PS is another thing. But you could probably just loop the pressure line into the return line and be fine with just a little oil in the system, wouldn't take much just to hook up the steering box either. Of...
  20. B

    K code exhaust manifolds w/ 302 who's running them

    Id only consider shorty's slightly better than stock manifolds and would only use them if there was a clearance issue or they were free. I'm pretty sure broncobowsher ran K codes maybe he will chime in at some point with some fitment info.
Top