• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Search results

  1. B

    Cylinder Head size help/advice on a 302 motor....

    Chamber CC choice really is up to you and if your engine is built already or you are going to build a engine as it will factor into your compression ratio. If you haven't built yet then you can use either and pick your pistons accordingly. As you've kinda learned already 170 or less would be...
  2. B

    Need opinion on 9" gear pattern

    Pattern looks ok I might try to get it a little deeper into the gear but it should work. Ive never used a torque wrench on side adjuster to set preload as it should be pretty much set once your backlash is achieved. Id probably shoot for around .009 or .010 on the backlash figure a new setup...
  3. B

    Edelbrock 1406 4bbl instal to a 76 Automatic

    A 500 cfm carb is pretty well suited for a street 302 unless you plan on running over 6000 RPM all the time. 600 cfm carbs are just a standard and will probably never come close to using all of it on a mild 302 unless you run over 8000 RPM. I also like how the 500 cfm carbs feel verse the 600cfm...
  4. B

    Car C4 swap into Bronco?

    You can use it but I would really look into what the 67 tranny has for input shafts, bellhousing size ect. Some had smaller input shafts, smaller bellhousings and other parts that are not always the most desired. Also some parts may not interchange between the 2. Although most internal parts...
  5. B

    Is there a consensus on best carburetor?

    As others pointed out there is no consensus on the best carb. Sooner o later they all have there issues. but can usually be fixed. I prefer holleys I've yet to have a accelerator pump diaphragm go out on one unless it was totally dried out from sitting on the shelf for years. Might help to...
  6. B

    Engine Number Questions

    Id say that D8 block would not be the block the bronco came with. It should have a D7 or D6 casting or sometimes ever earlier depending on what was left in a production run. Could have been a dealer replacement block as I believe that Z at the end indicates a replacement part. Also D8V would be...
  7. B

    Rock Auto no longer a favorite of ours...

    My beef with rock auto is you start adding items to a order and they come from one or two locations then add another part and you suddenly have parts coming from 4 locations and extra shipping costs to get them at that point it becomes cheaper to get locally. But on the other hand rock auto...
  8. B

    What size battery

    I tend to go with the largest one I can fit that has the most cranking amps. Not sure what I currently have in there at the moment but I know its not a little 24. Optimas don't seem to hold up like they used to. So I've stayed away from them.
  9. B

    Is this posi?

    Currie enterprises sells parts as well. Ive gotten parts from them in the past including a billet steel clutch cover kinda drives the price up but they don't blow out like the stock ones do. I'm not sure if they still sell them but they might its a good upgrade. Id check the shafts those gears...
  10. B

    factory carb help

    Here's a list of some bronco carbs for that year. Yes there are lots of #'s that can work. But really as long as you get one that was setup for a 302 and auto trans and the choke style you need your fine as there is really no difference in any of these carbs. D3BFAC, D3BFAD, D3BFAE, D3BFBC...
  11. B

    Timing Marker

    Sounds like your vac advance was hooked up on your last test but you may want to check what the dist mechanical advance should be. I'm not sure on the MSD but there are usually different amounts that can be depending on how its setup. If I remember MSD usually uses different bushings so you may...
  12. B

    Later two piece steering shaft in early column?

    It should work fine. About the only think I can think of that may come into play are the column bearing sizes as there were some differences between early and later bearings should be easy to tell if the shafts are identical in the bearing area then it was probably the column itself that...
  13. B

    302 Worth?

    It can be hard to sell engines for what they may have in them but it doesn't hurt to put the price up to what you want to get out of it. Give it some time and see what happens. I see a lot of engines such as your describing for near what they would cost retail but I have no idea if that's what...
  14. B

    Request for PTO information

    Would be interesting to see some parts with actual ford part numbers. I'm sure there are probably some out there but for the most part. That ford part number is just for a kit for either a 6 or 8cly. When one was ordered koenig probably just sent out that kit to a dealer. Basically yes a option...
  15. B

    Low pinion D44 axle from a 73-77 f250 questions?

    Wont work if you want to stay 5 lug. 3/4ton D44s brakes are bigger but brackets and posibbly the knuckles themselves wont clear 5 lug rotors plus the brackets are made for larger rotors so unless you get some custom 5 lug rotors theres really just no way to do it with those parts. There are...
  16. B

    Timing Marker

    I would say you have a late model 5.0 engine in there. Most likely that's why timing is read at the 10 oclock position. Irreguardless The first thing I would check as was said is your top dead center. Either verify that the current timing marks line up to that or create new ones that you can...
  17. B

    9" rear end vs. 8" rear end question

    Id agree go 9in if at all possible. The 8in is ok but expensive to build for what you get there's lots more available for the 9in and its just plain stronger. Could be different now but I seem to recall a lack of gear ratios available for the 8in plus if you wanted a traction device you were...
  18. B

    Request for PTO information

    I believe all the PTO's where either Ramsey or Koeing. I think you can find them on scouts and jeeps as well. Don't know if ford actually had a part number for them. Id suspect as was said they were not actually factory installed even though some literature suggest it. Most likely a dealer...
  19. B

    Bronco Drivetrain into mid-late 60s F100

    Might look into a fiberglass tub for the bronco they run about $5K Or there are steel body kits for $4K but they need to be assembled lots of fitting required or just replace what is bad on your current one might cost way less overall. As was said there could be some people in your area that can...
  20. B

    Off idle bog

    basically what gr8scott said. Off idle bogs are usually caused by not enough accelerator pump shot check adjustment if all is good there you may need a different pump cam or even a larger pump nozzle. Power valve opening point is usually not a issue just off idle as the accelerator pump is used...
Top