• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Search results

  1. B

    Mpg

    If your overall gearing is not to bad and you do some tuning on the engine you should be able to hit 11-12 no problem. You may want to check your timing and jetting. You may need to play around with the timing to find out what your engine likes best but there are gains to be had and they are...
  2. B

    Fuel pump eccentric

    could be possible that the dowel pin for the eccentric has sheared off possible due to cam gear bolt loosening. which is allowing the eccentric to kinda spin free and not operate the fuel pump correctly. Definetly a good idea to pull that timing cover kinda sucks but its better than having a the...
  3. B

    Bronco 289 cam help.

    Cams are a good way to get the power where you need it. As was said you need to have the correct one for your setup. Usually the performer cams mentioned are good for most everyone. Intake and carb mods are fine but they only move the power band upwards you see very little to no gains on the...
  4. B

    new heads ?

    As was said do a compression check and if it checks out hit up the machine shop. They usually always have heads available. now the down side is pretty much any stock head out there is going to cause a loss in compression as most if not all broncos had small 58cc chambered heads. plus 73 was like...
  5. B

    11 pack or 9 pack?

    While a lot depends on how the spring is made and what its capacity is. I would say that for the most part the 11 pack springs could be softer as far as ride but may have more load capacity overall and have more flex than the 9 pack springs. but like I said it depends on how there made and what...
  6. B

    9” rear end identification - was expecting Trac-Lok

    That's a open diff. equa loc and trac lok look pretty similar ie recessed ring gear bolts. also they will be 5/8 bolts where the open diff has 3/4in headed bolts. Both the trac loc and equa loc are fairly weak units its not uncommon for them to blow out the clutch cover. So that could be the...
  7. B

    Top of axle to frame measurement.

    The measurement of a stock height bronco is 7in front 6in rear. Lifts can vary in height even if its marketed as a 3.5in but they are usually very close to advertised heights.
  8. B

    Fuel filler hose - stumped on 2 options

    You will need the vent hose hooked to the filler neck. It allows for easier filling of the tank. You could run without it if you want but Id run it. I could be wrong but I'm pretty sure the charcoal canister doesn't hook directly to the gas tank there is usually a expansion tank that it hooks to...
  9. B

    Very best donor vehicle?

    Best donor would be a 76/77 bronco. Only thing you wouldn't get is a tilt column. Most of the items your wanting tend to be in high demand and tend to bring in more money for said parts vehicles. It would be nice if it was all one stop shopping but its not. Without knowing what your build needs...
  10. B

    How much fuel pressure will a Bronco valve take?

    Its design works equally well for vacuum or pressure. It doesn't care what forces are placed on it. It functions the same. Its nothing more than a oring on a shaft in a bore. Ive been running a 6psi electric pump for well over 30 years. When I did get a small leak I found the shaft was aluminum...
  11. B

    How much fuel pressure will a Bronco valve take?

    The selector valve uses a oring to seal technically it should hold up to anywhere from 100 PSI to at least 1000 PSI. But as I said its a old valve and if it has a aluminum shaft I would almost bet it has some corrosion and would probably leak. If it has a brass shaft then you may be ok. But I...
  12. B

    What do you all think about this?

    I usually see newer ones for under $4K of course not with 6in lifts or 35's in my area.
  13. B

    mpg method

    Basically making sure your engine is tuned correctly will probably net you the most increase. A few people have gave some tips there. Engine timing is a big one, then overall jetting. These are pretty cheap options that can make improvements. EFi doesn't always gain you mileage unless your...
  14. B

    How much fuel pressure will a Bronco valve take?

    Technically it should But with anything old and worn It may not hold long. Might be better off bypassing or getting a newer electric valve.
  15. B

    5.0 EFI high output VS FITECH EFI carb

    Id stick with what you have. Most likely your current EFI will easily handle the 331 needs with no retuning unless your building a wild motor. Of course getting a custom tune would be best for even a mild 331.
  16. B

    speedometer reading

    You need to figure out the percentage you are off and get a speedometer gear ratio adapter that will make the correction. I think most big truck shops can do this for you or know where you can get them locally or you can find them on line ebay has lots but sometimes they don't know the ratios...
  17. B

    Brown Arm Rests?

    Check econoline vans maybe 60's up to the late 80's maybe early 90's. the brown/ tan can be hard to find and as was said the drivers sides get torn up. I may have some pass side brown ones but they are a different color than the bronco ginger ones. Ebay is a good place to watch for some. I...
  18. B

    Original Bronco as an investment

    X3 If you need the room and no real plans for it. Then Id look at selling soon. Its no Cobra jet, Shelby, Boss or a Stroppe then investment value is really not there. As was said you cant really tell what the market will be but you know what it is right now. I think the market has pretty much...
  19. B

    Suspension question

    That's easy for home but what about when you want to stop somewhere?
  20. B

    Wiring Electric Fuel Pump to Ignition Switch

    All the safety features mentioned are good ideas. If you know what pump you have and the amps it draws some of these are not really needed. My carter electric fuel pump only draws 6amps max I believe its lower than that but I know its no more than 6. Anyhow the easiest place to wire is the...
Top