• Just a reminder that you won't be able to start new posts or reply to existings posts in the Archive forum.

    This is where all the old posts go so they can still be used for reference and searched.
  • Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

302 roller motor question

soala70

Full Member
Joined
Oct 28, 2004
Messages
154
I have a friend that has a 302 roller motor he took out of his mustang to install 351 Cleveland . It has only 1500 miles on it since he had it rebuilt got it for $500 other than oil pan of course what else am I looking have to do to it to install in my bronco. I want to put a explorer serpentine setup. Any and all help and suggestions would be appreciated.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,649
Sounds like a good score.

For the Explorer, just in case you were not aware the whole front end of the engine is part of it. So you'll be running the Explorer front timing cover and water pump.
Because it does not have the boss for a mechanical fuel pump, you will need to go electric if you carburetor. If EFI, this is what you'd be doing anyway.

Higher power alternator will have to bypass the ammeter, so a volt gauge will be needed.

Manual transmission? If so, you'll need to make sure you take care of the clutch linkage issue, as the later engines did not have a needed hole in the block for the clutch bracket. This kit is available if you don't want to make something:http://www.wildhorses4x4.com/product/EFI_Clutch_Equalizer_Conversion_Bracket

If your new heads have them, make sure to plug the air holes in the back of the cylinder heads if it hasn't been done already. BEFORE you install the engine! ;D

That's all I can think of for the moment.

Paul
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,649
Oh, in case you're keeping the transmission you're currently using, you're going to need to source a manual or automatic flywheel (flexplate) with 50oz imbalance. If you're running the original Bronco stuff, it will be the older 28oz stuff.
The Explorer damper will take care of the front end, but it's still up to you to make sure the tail end is compatible.
If you also got one of those with the engine, that's good, but you still have to make sure it's the proper 164 tooth truck flywheel for an 11" clutch, or large flexplate with the same number of teeth that is compatible with a Bronco C4 torque converter.

A few things to make sure of, that's for sure.

Paul
 
OP
OP
S

soala70

Full Member
Joined
Oct 28, 2004
Messages
154
Man thanks donk

Thanks for the input . What I want is a explorer front end use the C4 I have in it now with a carb for a short while then I plan on changing over to efi. I have read something on timing marks not lining up will I have a problem in this area ?
 

broncodriver99

Bronco Guru
Joined
Jan 27, 2008
Messages
4,780
Loc.
Glen Allen, VA
To run the Explorer serpentine setup you will either need to run the Explorer Damper or run an aftermarket crank pulley. If you run the Explorer damper your timing marks will line up fine. The biggest problem you will have is the explorer timing chain cover has no provision for a mechanical fuel pump so you will have to convert to an electric pump which you will need to do eventually for EFI anyway. Good thing is until you go EFI you can just run one of the frame mounted low pressure pumps.
 
OP
OP
S

soala70

Full Member
Joined
Oct 28, 2004
Messages
154
Thanks guys

I have always been a 67-72 Chevy guy but since I got my 1st bronco I have been addicted this is my second I am going to become a contributor here so I can share my build again thanks and any other tips on engine install would be appreciated
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
You shouldnt have to replace the oil pan. The mustang dual sump pan clears fine many people have used it. although I like the stock bronco pans better. but it doesnt matter.
You will also need a steel gear for your distributor as the roller cam will eat a cast iron gear.
 

broncodriver99

Bronco Guru
Joined
Jan 27, 2008
Messages
4,780
Loc.
Glen Allen, VA
I have always been a 67-72 Chevy guy but since I got my 1st bronco I have been addicted this is my second I am going to become a contributor here so I can share my build again thanks and any other tips on engine install would be appreciated

Welcome aboard buddy. ;) We will have you bleeding blue oval here shortly. Just kidding. That era of Chevy was a good time. But, you can't beat these old Fords. Looking forward to the pics.
 
Top