• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

35 spline axle question

Pops

Jr. Member
Joined
Mar 7, 2005
Messages
133
Loc.
Warsaw, In
I have a medium bearing rear end. I am getting ready to upgrade to 5.13 gearing and am wondering if 35 spline axles will fit in the torino bearinged
9inch rear end? Or an I limited to 31 spine ?

Thanks in advance for any info you mite have.
Pops
 

GubNi

Sr. Member
Joined
Oct 31, 2004
Messages
481
Loc.
Northeast TN
Why bother? 31 spline is plenty. I've got a friend with 31 spline and 38's with a locker. If you need bigger get a 14 bolt or Dana 70 so you can go full float.
 
OP
OP
Pops

Pops

Jr. Member
Joined
Mar 7, 2005
Messages
133
Loc.
Warsaw, In
I am trying to follow the rule only break it once. This is my daily driver/trail rig. Down time really sucks.
 

welndmn

Bronco Guru
Joined
Nov 12, 2001
Messages
2,112
Yes, there are some conversion bearings to run the 35 spline axles in that housing, but don't forget, you need to upgrade your 3rd member as well.
I would call up Currie and talk to them. It may be better to just swap a Big bearing rear end in.
 
OP
OP
Pops

Pops

Jr. Member
Joined
Mar 7, 2005
Messages
133
Loc.
Warsaw, In
I have a 28 spline detroit locker with 3.50s in it now. So the 28 spline will be swapped into my 1970 Torino gt. So since I'm replacing it anyway I want to go as big as possible. Replace things once.

Thanks for the info.
 

br0nc0xrapt0r

Loves pickles
Joined
Sep 28, 2007
Messages
5,439
I have a 28 spline detroit locker with 3.50s in it now. So the 28 spline will be swapped into my 1970 Torino gt. So since I'm replacing it anyway I want to go as big as possible. Replace things once.

Thanks for the info.

no I'm pretty sure he means you need a nodular third member housing to fit the 35 spline carrier, I just did the research and a question post on this topic and unless you are going to run a spool I don't think it will be possible to find a locker to run 35 spl shafts in a stock 3rd housing.

hope this helps.
 

Dusty

Bronco Guru
Joined
Jun 28, 2001
Messages
2,969
I used to run 35-spline Currie axles in my '75 torino-style housing. Give Currie a call, they'll set you up. Mine had tapered roller bearings.

Dusty
 

Dusty

Bronco Guru
Joined
Jun 28, 2001
Messages
2,969
Of course it was. I never had to worry about breaking itty bitty 31-spliners :D

I sold that housing and axles a few years back but kept the nodular center, re-used it in the big bearing full width 35-spline 9" that's currently under my wife's rig "Coco".

Dusty
 

NC-Fordguy

Bronco Guru
Joined
Jan 30, 2006
Messages
1,317
Loc.
Bethel/Greenville NC
I'm running 35 spline on a 74 big bearing.

You'll have to get a new carrier/locker and 3rd member.

Wasn't a big deal for me to get a new 3rd as when the 28 spline axle broke it destroyed the detroit and ring gear
 

Bronchole

Bronco Guru
Joined
Mar 24, 2004
Messages
1,611
Loc.
Chatsworth, Ca (LA)
If you are in touch with the fact that in going 35 sp you will have to replace the case and the locker/spool the total build cost wetween going 35 or 31 is only something like $200 on $1200 worth of parts. If I were starting from scratch, upgrading from 28 spline, its a no-brainer. But if I already had a 31 spline Detroit locker, I'd have to get decent money for the used Detroit locker to consider not upgrading to the 35 spline everything.

BTW, Summit Racing a few years ago had the sweet deal on Strange Engineering "econo nodular" cases. They are only a few times stronger than the factory Ford nodular cases (which are far stronger than the standard Ford cases) but in my opinion they are pleanty strong enough. They are in the mid $200 range delivered to your door. Food for thought when you are going to be looking at nodular cases in the $450+ range anywhere else.

Dan
 
Top