• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

351w EFI install

OP
OP
lonesouth

lonesouth

Contributor
Bronco Guru
Joined
Dec 18, 2003
Messages
5,048
one issue I know I will need to address is that the BC hard lines are dangerously close to my exhaust under the driver's seat where the front and rear lines meet. I mounted my pump above the frame and used EFI hose to go from the hard line to the pump and back. I'm debating cutting the exhaust off right after the t-case and dumping underneath since I'll be redoing the exhaust anyway later on.
 

Timmy390

Contributor
Bronco Guru
Joined
Jan 1, 2011
Messages
5,948
Loc.
Conway, AR
I do have true dual exhaust and did run my hard lines on the D side. The closest the feed/pressure line will be is 5.5 inches from the exhaust and that's up just in front of the cross member well in front of the HP pump near the tank. The return line might be half an inch closer? They're mounted one below the other along the side of the frame as high as I could get them.

I'm mounting my pump on the frame cross member just above the sending unit and running 3/8 SS braided lines from the pump to the hard lines.

I'm using my existing exhaust so I only have to build from the shorties back to the cherry bombs.

Tim
 

chuzie

Bronco Guru
Joined
Jul 21, 2006
Messages
2,761
A hard mounted fuel pressure gauge is worth every penny for troubleshooting efi. Highly recommended!
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
The oil fill spout has a 5/8" barb, that I have adapted down to 3/8" for the pcv. There is a hole in the drivers side for the vent that connects to the intake, but there is not room to run a valve there, just an elbow. At this time, there will not be a pcv valve in my pcv system.

I would figure out a way to plumb in the PCV valve before you start it. If you don't, I think you'll be fighting a battle trying to figure out why it's not running completely right.

And I'm not sure I read you correctly, but just in case, you do NOT run direct vacuum from the intake manifold to the valve cover elbow. The only full vacuum has to go through the metered PCV valve. Either that, or nothing at all. Better nothing than a vacuum leak, but better still having a functioning PCV rated for an injected 351 before starting.

A little surprised that the existing nipple in the filler neck was so large. Usually that's the hose that connects to the intake tract, either before the throttle-body, or directly to a hose fitting on the throttle-body just ahead of the throttle plate.
I wonder if the particular engine that those came from was either meant to house the valve itself there at the filler, or was pre-EFI and just had a big hose to the air filter.

Since you are running the upper oriented with the TB to the passenger side, the filler neck hose would easily be connected to the throttle body right there. Not sure the best place to put a valve with your setup, but I'm sure it's been done.
I'm trying to remember where a friend put his on a 351 with stock Explorer upper and some sort of stock valve cover setup. I'll see if I can find out what he did.

Good luck.

Paul
 
OP
OP
lonesouth

lonesouth

Contributor
Bronco Guru
Joined
Dec 18, 2003
Messages
5,048
hadn't thought to put the PCV valve in the filler neck nipple. I'll see if it fits.
 

Timmy390

Contributor
Bronco Guru
Joined
Jan 1, 2011
Messages
5,948
Loc.
Conway, AR
I had to ditch my van valve cover due to how tail the oil fill was and went to the "yard" and got on off a 5.8L F150. The 5/8 barb on the oil fill was ran into the air cleaner box via a rubber hose and a hard plastic hose. No PCV valve was there.

I used the PCV valve in the back of the GT40 lower T'd the 3/8 line and stuck the 3/8 line into the 5/8 line connected to the oil fill. It was easy for me as the oil fill is P-side rear because the Explorer upper is in the way on the D-side.

have not fired mine up yet so hoping that works......

Tim
 

dclack

Sr. Member
Joined
Feb 16, 2012
Messages
402
Yeah, the GT40 lowers have a hole in the back for the PCV just like the 302 lowers. The 351 trucks have the PCV in a hose on top of the passenger VC. I used the truck VCs but swapped them, so the large 5/8 line connects to the TB on the passenger side. On the drivers side, there is an elbow coming out of the VC, 90° hose that houses the PCV, and PCV connected to the intake. This results in the PCV laying on its' side next to the fuel rail, but I don't think that's a problem and it runs just fine for me. I'll see if I can get some pics.
 
OP
OP
lonesouth

lonesouth

Contributor
Bronco Guru
Joined
Dec 18, 2003
Messages
5,048
I figured out that I'm going to put the PCV into the 5/8 tube instead of the brass barbed fitting, then run 3/8 to the intake. On the driver's side, I'll run an elbow out of the valve cover and 3/8 to the coupling between the mas air body and throttle body. It isn't elegant, but it should accomplish the same thing, only metered air in the PCV system.
 

chuzie

Bronco Guru
Joined
Jul 21, 2006
Messages
2,761
Here is what I am doing. Unlike you, my issue with the valve covers was finding a 1/4 turn breather that adapts to hose barb. In the end, I used a 1/4 turn PCV breather and cut up a PCV valce to use for the hose barb.

For your setup, I would run the PCV in the back of the lower manifold and run the line to the port on the upper intake. Then connect the line you have coming from the oil fill on the intake to the throttle body.

Some folks debate whether or not it is necessary to have both valve covers breathing but you are running an open case and not nearly the RPM that would generate so much pressure in the case that one ported cover couldn't handle it.

Just make sure the port on the other cover is sealed as well as your dip stick, otherwise they can both be sources of a VAC leak. I would also recommend removing all those extra VAC ports on the upper. Most folks use those cheap rubber caps but they deteriorate very fast and you will end up chasing VAC leaks 6 months down the road.
 

Attachments

  • C360_2016-02-02-18-57-57-199.jpg
    C360_2016-02-02-18-57-57-199.jpg
    94.8 KB · Views: 199
  • C360_2016-02-02-19-02-26-447.jpg
    C360_2016-02-02-19-02-26-447.jpg
    128.7 KB · Views: 188

dclack

Sr. Member
Joined
Feb 16, 2012
Messages
402
The truck lower intake does not have a PCV port in the back like your lightning lower does. Hence the need to vent from vc to vc. Here's my setup...





 

chuzie

Bronco Guru
Joined
Jul 21, 2006
Messages
2,761
Well crapola. Stupid truck lowers! ;)
 
Last edited:
OP
OP
lonesouth

lonesouth

Contributor
Bronco Guru
Joined
Dec 18, 2003
Messages
5,048
i've mostly got the pcv stuff sorted out. I tracked my fuel issue(for now) to a faulty pressure regulator. It was pretty much wide open, so no pressure. I replaced it, and now I can maintain 40psi.

new issue. I got the dizzy stabbed and wired up. I tried starting, I had it going for a second, but then it died. It will catch whe cranking, but will never take over on its own. I checked timing while cranking and I've got 10* BTDC.
 
OP
OP
lonesouth

lonesouth

Contributor
Bronco Guru
Joined
Dec 18, 2003
Messages
5,048
some collaborative diagnostics on facebook pointed me to air in the fuel line. once that was bled out, she purred to life. But then wouldn't start again. Checked the fuel rail again, and the pump was pulling fuel from the tank. Going to get a new one tomorrow and more it to the top of the rear crossmember in front of the tank.
 
OP
OP
lonesouth

lonesouth

Contributor
Bronco Guru
Joined
Dec 18, 2003
Messages
5,048
What is the impact if I run without O2 sensors? Will it run a default program like it has just started and not warmed up, run rich, run like absolute garbage?
 

Timmy390

Contributor
Bronco Guru
Joined
Jan 1, 2011
Messages
5,948
Loc.
Conway, AR
It should run but rich as heck from what I understand. Shouldn't cause a no start situation.

Tim
 
OP
OP
lonesouth

lonesouth

Contributor
Bronco Guru
Joined
Dec 18, 2003
Messages
5,048
Thanks, I was thinking it is something I could leave out if I run out of time before SOWEGA.
 

shill37

Jr. Member
Joined
Dec 27, 2011
Messages
59
Here is what I am doing. Unlike you, my issue with the valve covers was finding a 1/4 turn breather that adapts to hose barb. In the end, I used a 1/4 turn PCV breather and cut up a PCV valce to use for the hose barb.

For your setup, I would run the PCV in the back of the lower manifold and run the line to the port on the upper intake. Then connect the line you have coming from the oil fill on the intake to the throttle body.

Some folks debate whether or not it is necessary to have both valve covers breathing but you are running an open case and not nearly the RPM that would generate so much pressure in the case that one ported cover couldn't handle it.

Just make sure the port on the other cover is sealed as well as your dip stick, otherwise they can both be sources of a VAC leak. I would also recommend removing all those extra VAC ports on the upper. Most folks use those cheap rubber caps but they deteriorate very fast and you will end up chasing VAC leaks 6 months down the road.

Nice job on the intake chuzie!!
PS. Your inbox is full.
 

chuzie

Bronco Guru
Joined
Jul 21, 2006
Messages
2,761
Running in closed loop, especially with a 351w is not ideal off road.

I may have missed where you mentioned your pump config and tank type.

Inbox fixed. Fire away.
 
Top