• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

5.0 Sticky Throttle

SC74

Contributor
Bronco Guru
Joined
May 24, 2004
Messages
3,472
This problem all started when I unhooked my throttle cable from the throttle lever so that I could remove the cable bracket. I had to remove the bracket so that I could fab another bracket to mount to the same 2 bolts that the throttle bracket does.

I hooked the cable back up to it's "snap" on the lever and it has a very stiff spot in it at idle. If you punch it to get past it, it is smooth, but won't return all the way back to idle - stays up around 1,200 RPM and it idles around 600-700ish. I can manually get it back down to idle by pushing the lever under the hood with my hand, but it won't return under its own power.

I snapped the cable off and it is smooth. When I used my hand to adjust the throttle (which also opens the air butterfly) it was very sticky in the closed (or idle) position. I worked it back and forth a few times and it may be a LITTLE better, but not much - still won't return to idle.

I never did anything to effect this part. All I did was remove the bracket that sits completely separate from the butterfly lever.

Any ideas? It didn't do this before so I have obviously effected something but don't know how.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,111
Clean the carbon buildup in the throttle body is a good start.

I had a similer issue with a 2.9 in a BroncoII. I would have to snap the throttle open first thing in the morning then it would be good all day. after it cooled off the aluminum housing would contract and stick the throttle blade requiring a snap to open. I fixed it with a slight increase in the min airflow screw, quarter turn or so. The computer took a day to relearn what idle is (back before I know the TPS adjustable). After that it was good for years (until the rest of the truck fell apart).
 

JohnJohn

Contributor
Bronco Guru
Joined
May 6, 2005
Messages
2,179
Loc.
Richmond
Would a stronger return spring also help?
I have two on mine. One on the cable and one from the firewall to the linkage. The cable one is not that strong. I am using the BC cables but added the firewall spring. I wanted to make sure it would return.
Not that I drag race my Bronco but I believe NHRA regulations require two return springs.
 
OP
OP
SC74

SC74

Contributor
Bronco Guru
Joined
May 24, 2004
Messages
3,472
A second spring is a good idea and I'm sure I could find a place to make one work. That will help it return, but still have that rough spot coming out of idle to throttle.

I will also clean the throttle body and see if its not something hanging on the butterfly. What would be the best thing to spray - MAF cleaner?
 

70injectedbronc

Jr. Member
Joined
Jan 19, 2012
Messages
84
Loc.
Coeur d'alene
Could be any of these things but on mine a few weeks ago was doing this. Ended up getting bad enough to stay stuck and I had to kill the motor. Mine was the throttle cable just where it meets the firewall. The cable was old anyway and the angle it was at started to fray it to where they were catching. Got a universal replacement from the local auto store.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,111
Could be any of these things but on mine a few weeks ago was doing this. Ended up getting bad enough to stay stuck and I had to kill the motor. Mine was the throttle cable just where it meets the firewall. The cable was old anyway and the angle it was at started to fray it to where they were catching. Got a universal replacement from the local auto store.

I had that too. Mine was the angle the cable was pulling through the firewall. The cable was pulling at an angle and sawing at the housing. It wore a groove and eventually the groove was tight enough to start grabbing and holding the cable.
 

Pa PITT

Contributor
Bronco Guru
Joined
Jul 15, 2005
Messages
11,300
Loc.
Stephenville TEXAS
I too drove a BroncoII 2.9 for about 3 years and 385000 miles .. It needed cleaning about ever 20k. got old for sure .. The Best cleaner I found was a Ford spray foam.
Sprayed the foam on let it eat the black ... Open throttle some and spray more into the throat .. Mine also seemed to like the Lucus cleaner ..
 
OP
OP
SC74

SC74

Contributor
Bronco Guru
Joined
May 24, 2004
Messages
3,472
I have eliminated the cable... I unhooked it and left it in place and there is no resistance at the pedal.

I leave tomorrow for a week so won't be able to look further into this until next weekend or the following week. I will bring this thread back to life when I return and let you know what I find.

Thanks for all of the help!
 

ransil

Bronco Guru
Joined
Sep 6, 2003
Messages
8,138
I use carburetor return springs on the EFI conversions, I have BC or lokar cables and hook the spring to the old throttle bracket was located.

I have tried tightening up the spring on the throttle shaft and the BC spring on the cable neither was acceptable.
 
OP
OP
SC74

SC74

Contributor
Bronco Guru
Joined
May 24, 2004
Messages
3,472
Still no resolution here... :mad:

I first hosed the linkages down with PB Blaster - that did not help.

Next I removed the throttle body and cleaned the inside of it - that did not help.

Next I used some PB Blaster in the top and bottom pivots of the butterfly - that did not help.

My next step is to remove the butterfly and see if it's a butterfly problem or a linkage/shaft problem.
 

JohnJohn

Contributor
Bronco Guru
Joined
May 6, 2005
Messages
2,179
Loc.
Richmond
Have you thought about visiting a local junk yard and picking up another throttle body? I would think you could get one cheep and could at least check it out to see if it works better than the one you have.
 
OP
OP
SC74

SC74

Contributor
Bronco Guru
Joined
May 24, 2004
Messages
3,472
Just took mine apart and the shaft looks bent - don't know how it got this way but unless it's supposed to be angled to the linkage, it is bent.

I have some spare 5.0 parts so I'm going to go digging to see if I don't already have a spare to throw on there and check it.
 
OP
OP
SC74

SC74

Contributor
Bronco Guru
Joined
May 24, 2004
Messages
3,472
Issue solved! It was the bent shaft. The spare throttle body we had was modified with a larger butterfly so I just robbed the shaft and put it in mine. It now returns to closed under it's own spring power where-as my original one had no return.

What I did learn by doing the swap was that my idle adjustment screw is not there - didn't even know I was supposed to have one until looking at the spare throttle body.
 
Top