• Just a reminder that you won't be able to start new posts or reply to existings posts in the Archive forum.

    This is where all the old posts go so they can still be used for reference and searched.
  • Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

67 Bronco Build

OP
OP
R

RVZIO

Full Member
Joined
May 9, 2019
Messages
163
Loc.
New Smyrna Beach
The rear tank uses a flat metal strap with a funky end that locks into the outside of the frame on the passenger side and a J-bolt on the drivers side that supports about midway of the tank. I just took one out!

Your earlier pics of the front show a 5/8" (roughly) vent hose with the large fill hose beside it. The early Broncos, '67 included did not have a vented fill spout and would burp when filling. There may be a chance that your filling system is from a later EB or something else entirely. So, if you have the option, and want to run a front tank, pick one up from a newer version that had the vent hose so it fills easier.

I was just looking at a tank kit from Bronco grave yard. Has the metal tank,sender, J bolts , strap, main fuel hose and a vent hose. Looks like all of that will fit. Thank you for the info
 
OP
OP
R

RVZIO

Full Member
Joined
May 9, 2019
Messages
163
Loc.
New Smyrna Beach
I was just looking at a tank kit from Bronco grave yard. Has the metal tank,sender, J bolts , strap, main fuel hose and a vent hose. Looks like all of that will fit. Thank you for the info

If I get this unit I would still be able to add the 2nd small aux tank?
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Yes. There's nothing in one tank that precludes the use of the other.
If you don't have the dash switch for the gauge, or the floor valve for switching the tanks, you'll have to add them.

Paul
 

.94 OR

Contributor
Bronco Guru
Joined
Jul 5, 2009
Messages
2,215
Loc.
Willamette Valley, OR
He could also add an electric fuel switching valve and wire it to a dash switch eliminating the manual valve.

But, but by the looks of the hoses he provided, the vehicle was likely equipped with a front tank at one time.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Definitely. I did that with mine when the valve started leaking. Even though you could still buy them new at the time, or rebuild with easy to fine o-rings, the electric one just made the most sense.
I even spent the extra to use the motorized type (as opposed to the solenoid type) so I could plumb in return lines even when I was carbureted.

Glad you brought that up.

Paul
 
OP
OP
R

RVZIO

Full Member
Joined
May 9, 2019
Messages
163
Loc.
New Smyrna Beach
I'm sure this has been asked a ton of times but could I use my 2 post lift to remove the body and roll the chassis out to do some work and then roll it back under. I believe the mounts are removed or gone. Probably a few other items like steering, clutch rod, starter wires ummmm Spot to locate lift arms, where is best. Any posts showing the body lift with a 2 post lift
 

904Bronco

Contributor
Bronco Guru
Joined
Sep 28, 2004
Messages
6,720
Loc.
San Martin, CA
I'm sure this has been asked a ton of times but could I use my 2 post lift to remove the body and roll the chassis out to do some work and then roll it back under. I believe the mounts are removed or gone. Probably a few other items like steering, clutch rod, starter wires ummmm Spot to locate lift arms, where is best. Any posts showing the body lift with a 2 post lift

There are a number of ways to do this, this is the method I have used twice.

4x4 with blocks and spacers to support the body. If you remove the doors then you need to add reinforcement to the front half of the body. The idea is to capture a number of the body mount areas and/or support the body where there is good sheet metal. If the sheet metal is not good, well that should be done before you move the body off the frame.

When you put the body back on the frame let it sit a day or so to settle before tightening up body mount bolts.
 

Attachments

  • DSCN5231.jpg
    DSCN5231.jpg
    75.7 KB · Views: 91
  • DSCN5230.jpg
    DSCN5230.jpg
    67.6 KB · Views: 79
  • DSCN5229.jpg
    DSCN5229.jpg
    78.7 KB · Views: 82
  • DSCN3877.jpg
    DSCN3877.jpg
    130.8 KB · Views: 86
  • DSCN3363.jpg
    DSCN3363.jpg
    90.9 KB · Views: 91
OP
OP
R

RVZIO

Full Member
Joined
May 9, 2019
Messages
163
Loc.
New Smyrna Beach
There are a number of ways to do this, this is the method I have used twice.

4x4 with blocks and spacers to support the body. If you remove the doors then you need to add reinforcement to the front half of the body. The idea is to capture a number of the body mount areas and/or support the body where there is good sheet metal. If the sheet metal is not good, well that should be done before you move the body off the frame.

When you put the body back on the frame let it sit a day or so to settle before tightening up body mount bolts.


That looks like a great way to lift the body. I planned on leaving the doors on to try and keep things in line as much as possible. Great pictures for me to follow, Thank You
 
OP
OP
R

RVZIO

Full Member
Joined
May 9, 2019
Messages
163
Loc.
New Smyrna Beach
So today I ordered the gas tank and kit since I have nothing. Also removed the filler tube and cleaned it up a little. Baby steps for now. I know the motor runs with gas down the carb but the tank will let me get more things looked at. Then off with body a here we go. Hey after so many corvette restores this one has so much room. Anyway pretty cool to get started.
 

Attachments

  • 20191126_131305.jpg
    20191126_131305.jpg
    54 KB · Views: 92
  • 20191126_124310.jpg
    20191126_124310.jpg
    125.3 KB · Views: 83
  • 20191125_062326.jpg
    20191125_062326.jpg
    124.3 KB · Views: 86
  • 20191125_062305.jpg
    20191125_062305.jpg
    119.8 KB · Views: 100
OP
OP
R

RVZIO

Full Member
Joined
May 9, 2019
Messages
163
Loc.
New Smyrna Beach
New tank kit coming Monday. The main fuel line from the tank to motor looks to part metal by carb. and rubber in the middle strapped to the chassis. Could not find a continious metal line to buy. For no I will use rubber to get motor running.
 
OP
OP
R

RVZIO

Full Member
Joined
May 9, 2019
Messages
163
Loc.
New Smyrna Beach
May I ask, since I have rusted out floor panels but also have rusted out portion of the behind the seats running across. More difficult to install a one piece floor panel or do them in the available sections.
 
OP
OP
R

RVZIO

Full Member
Joined
May 9, 2019
Messages
163
Loc.
New Smyrna Beach
Pretty impressed that my grave yard tank kit came today (Sat.) when it was due Mon. Even with the holiday. Pretty cool. Will get started next week.
 

rjcruz27

Sr. Member
Joined
Dec 2, 2014
Messages
369
I did the full piece floor. If you have someone to help it went it fine. Just do all your prep work before you put it in.
 
OP
OP
R

RVZIO

Full Member
Joined
May 9, 2019
Messages
163
Loc.
New Smyrna Beach
I did the full piece floor. If you have someone to help it went it fine. Just do all your prep work before you put it in.

Thanks man for the response. I was thinking that might be the way to go. One giant piece, done. Any particular vendor and or fitting issues.
 
OP
OP
R

RVZIO

Full Member
Joined
May 9, 2019
Messages
163
Loc.
New Smyrna Beach
Can somebody give me a measurement of the rear fuel tank strap bends. They look to be about 4". Not sure about the angle maybe 33 degrees or 45. There are 2 small hose lines up near the top of the tank. I saw a picture where a guy ran a U shaped piece of hose to block off I guess.
 

.94 OR

Contributor
Bronco Guru
Joined
Jul 5, 2009
Messages
2,215
Loc.
Willamette Valley, OR
Mine is bent a bit on the passenger side for who knows what reason. This is from a '71 tank so not sure if a '67 would be much different.

I take no credit for disoriented photos.
 

Attachments

  • IMG_5261.jpg
    IMG_5261.jpg
    92.1 KB · Views: 69
  • IMG_5262.jpg
    IMG_5262.jpg
    59 KB · Views: 55
  • IMG_5263.jpg
    IMG_5263.jpg
    78.5 KB · Views: 62
  • IMG_5264.jpg
    IMG_5264.jpg
    58.1 KB · Views: 61
  • IMG_5265.jpg
    IMG_5265.jpg
    74.3 KB · Views: 62
  • IMG_5266.jpg
    IMG_5266.jpg
    76.2 KB · Views: 56
OP
OP
R

RVZIO

Full Member
Joined
May 9, 2019
Messages
163
Loc.
New Smyrna Beach
Mine is bent a bit on the passenger side for who knows what reason. This is from a '71 tank so not sure if a '67 would be much different.

I take no credit for disoriented photos.

Great 94 I was close but the pictures help. I noticed on a few of the builds that the J bolt is on about the same angle as the strap instead of straight up and down. I guess as long as it hold the tank is the main thing. I will get a picture of the 2 small open tubes kinda right near the top side of the tank.
 
OP
OP
R

RVZIO

Full Member
Joined
May 9, 2019
Messages
163
Loc.
New Smyrna Beach
That small setup in the upper left of your picture. Looks like a U shaped small hose. Do they sell that premolded?
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
The main fuel line from the tank to motor looks to part metal by carb. and rubber in the middle strapped to the chassis.

Most were rigid plastic along the frame, metal from the pump to the carb, and rubber at all the junctions.

Could not find a continious metal line to buy. For now I will use rubber to get motor running.

Lots of people do rubber, but some bend up their own hard line. There are kits available that you might have seen already, from some of the vendors, but they are not all one long piece as far as I know. There are junctions, likely to make them easier to ship.

That small setup in the upper left of your picture. Looks like a U shaped small hose. Do they sell that premolded?

While there might be some 1/4" hose pre-molded into a U-shape, that looks like what everybody I know uses and just a piece of hose doubled over.
Those are your evaporative emissions vent tubes though, for '70 to '75 Broncos. And are good things to keep functional if you can.
If yours was originally equipped, your gas cap will be "non-vented" accordingly. If this is a swapped-in tank to an earlier year though, there should be no venting issues as the fuel level goes down from use.

Keeping them intact requires a charcoal canister, but if you're going to be parking this thing in the family garage it's usually considered a good thing in the long term.

Paul
 
Top