• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

67 with a surge

TNcowboy

Full Member
Joined
Aug 29, 2019
Messages
220
I've got a '67 Bronco with a stock 170...1100 carb and load a matic distributor

The idle is slightly rough, but barely perceptible. It does buck and surge when either accelerating or cruising.Vacuum is 17.5 and has a very slight needle wobble...less than an inch of vacuum. Timing is set a 6 degrees.

I've rebuilt the carb. When I did I noticed that the power valve was stuck open. I was able to lube it and get it to move freely. I changed rotor cap wires and plugs. I've installed a Petronix ignitor. The distributor diaphragm is working as it should. The old coil primary circuit was out of spec so I changed it out to a petronix 1.5 ohm unit I changed out the fuel pump and fuel tank to a 23 gallon. The truck had varnish old gas in it so I changed the pump as a precaution. I installed a fuel regulator because the pump is putting out almost 9 psi...now 4.5 psi

This weekend I changed out the spark plugs again, warmed it up and drove it around the farm...still surging. Back at the shop I pulled the plugs..see pic . Plug 1 still looked new..insulator still white, plug 2 had a little color to it, plugs 3 and 4 were carbon fouled, plug 5 had a brown tone, plug 6 did as well but slightly lighter. This plug pattern is just weird and the only thing I can think of is I've got valve issues in holes 3 and 4.

I'm going to do a compression check but was wondering if you all had any insight into this

I've also posted this at Fordsix.com

Thanks
 

Attachments

  • 3F11BAEA-414A-4930-B456-29D002AC30B2.jpg
    3F11BAEA-414A-4930-B456-29D002AC30B2.jpg
    136.8 KB · Views: 64
OP
OP
TNcowboy

TNcowboy

Full Member
Joined
Aug 29, 2019
Messages
220
Firing order is right

The vacuum is at 17.5 psi so I doubt that it has a vacuum leak, also that would case those cylinders to be lean.

I'm thinking the compression check will throw some light on it.

Waiting for it to arrive. My old set is missing the 18mm adapter
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,112
I'm guessing carb issue. Not atomizing like it should. 3 and 4 are getting fuel drooling into them. 1 and 6 are lean with the long run.
 
OP
OP
TNcowboy

TNcowboy

Full Member
Joined
Aug 29, 2019
Messages
220
I'm guessing carb issue. Not atomizing like it should. 3 and 4 are getting fuel drooling into them. 1 and 6 are lean with the long run.

Interesting observation
One other little wrinkle...earlier this fall wife and I took a 4 hour ride and it ran like a sewing machine. Started surging a week or so later

I'm still not convinced that the power valve is operating properly. I know I can get a replacement carb but I'd like to try and keep it stock. Problem is I can't find any replacement parts for the power valve.

Anyone have a source or someone who can rebuild the valve?
 

jckkys

Contributor
Bronco Guru
Joined
Mar 15, 2012
Messages
5,221
A surge usually indicates a lean condition. So you're thinking the problem is with the power valve is sound. Mike's Carburetor made a great video addressing the 1100 power valve fix. I would start with that. There are also many tiny passages that need special attention. The video addresses this too. Lots of new parts at one time doesn't help with diagnoses.
 
OP
OP
TNcowboy

TNcowboy

Full Member
Joined
Aug 29, 2019
Messages
220
A surge usually indicates a lean condition. So you're thinking the problem is with the power valve is sound. Mike's Carburetor made a great video addressing the 1100 power valve fix. I would start with that. There are also many tiny passages that need special attention. The video addresses this too. Lots of new parts at one time doesn't help with diagnoses.

Agreed the lots of new parts idea and should have said that I glossed over the process but things were done one step at a time...I just mercifully left out the play by play.
Mike's addresses the power valve but only to lube it. He did not address the rebuilding of the valve. I did lube it and get it to operate smoothly BUT that does not translate to operating properly when running. the passage for the power valve is clear. The carb was cleaned in Chem-dip and all the passages I could find were blown out as well.
 

jckkys

Contributor
Bronco Guru
Joined
Mar 15, 2012
Messages
5,221
He did remove the welch plug and offer a replacement. This is as much access to internal parts as there is. I don't see what more a rebuild would include. 1100s don't have a diaphragm power valve or metering rods. If the parts move freely the only other restriction would be a blocked or partially blocked passage. Maybe an overnight soak in Simply Green would help. It does with 2 and 4 barrels.
 
OP
OP
TNcowboy

TNcowboy

Full Member
Joined
Aug 29, 2019
Messages
220
He did remove the welch plug and offer a replacement. This is as much access to internal parts as there is. I don't see what more a rebuild would include. 1100s don't have a diaphragm power valve or metering rods. If the parts move freely the only other restriction would be a blocked or partially blocked passage. Maybe an overnight soak in Simply Green would help. It does with 2 and 4 barrels.

I saw that...I was thinking that if you could pull the valve plunger you could do a more thorough cleaning. I could pull the carb again and try to soak it in simple green overnight. I'm getting pretty good at tearing these apart. This'll be 3rd time for this one.

The guys at Fordsix.com were saying that this plug pattern didn't suprise them at all...this log head design is somewhat inefficient...outboard plugs get starved while 3 and 4 typically run rich
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
The vacuum is at 17.5 psi so I doubt that it has a vacuum leak, also that would case those cylinders to be lean.

I don't think it's always that simple.
You can have a tiny vacuum leak that's not enough to drop your reading by much, if any, but still be more than enough to get an occasional rough idle.
Maybe not enough to cause your lean surge, but still enough to add to another issue.
So whenever diagnosing this kind of thing I always do a deep check for vacuum leaks. My go-to is carb-cleaner or brake-cleaner, but just about anything will do.

Carry on with your other directions, but don't ignore the vacuum leak possibility.

Paul
 
OP
OP
TNcowboy

TNcowboy

Full Member
Joined
Aug 29, 2019
Messages
220
Thanks Paul

You might be right. I know that these small block 6's are also notorious for cracked intake manifold at the head. Extra frustrating since the two are one casting on these

I'll try and dig deeper this weekend. Compression tester due Monday so we'll see about compression then
 
OP
OP
TNcowboy

TNcowboy

Full Member
Joined
Aug 29, 2019
Messages
220
Quick update

Had some time this evening to do a little more investigation

First, the pcv valve is bad. Put your finger over the end while running and the rpms drop almost 200 rpms not the 40 or so that you'd expect. I plugged the hose and test drove. Still surging and acting like it's running out of fuel. Fuel filter is good. BTW I readjusted the idle speed and fuel mix screw. Vacuum is 18.5 inches.

Re ran the compression check with the engine warm and here's the results
1...172
2...162. Added oil and it was 167. Not significantly higher
3...172
4...182
5...170
6...182

Wondering if valve lash at #2 is correct or if there's a valve problem

None of the plugs were fouled upon pulling them for the test.

One other thing that is odd. As you know the vacuum line between carb and LOD distributor is hard line. Directly below the distributor diaphragm is the motor mount which is bowled at the bottom (see B in picture). There was a small amount of gas at the bottom and the threads on the fitting at the distributor had a tiny amount of gas residue on them. Removed the fitting to see if the line had gas in it...it was dry as far as I can tell. Also because of the gas and vacuum lines (one for distributor, one for vacuum windshield wipers) touching I don't think gas could have clung to the line and dripped into the motor mount

Here's a picture
 

Attachments

  • 60FD70D8-7931-468A-8791-647CA5772DFB.jpg
    60FD70D8-7931-468A-8791-647CA5772DFB.jpg
    111.2 KB · Views: 37

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
I'm not saying it's not bad, but I've had perfectly good PCV valves that easily dropped the rpm 200 or more. Those were V8's though, and that could be a difference as well.
Also had some that only dropped rpm a fraction of that too, so I don't know what the proper result really should be.

But an incorrect PCV valve can be just a bad as a failed one if it's wrong enough. Lots of them cross over, but many don't.

Those look like pretty decent compression numbers to me. Even the lowest and highest are not very far out of spec from each other. Isn't the limit 10% from high to low? You're just barely out of that, but still at very decent numbers overall.

Did we talk about ignition timing? Did you check for vacuum leaks using a spray bottle of something? Water? WD-40?
Engine's too clean to use much carb cleaner for too long, but brake cleaner would evaporate before buggering the paint I would think. Still, something more benign would be called for if much of the paint is as clean as what little we can see in the pic.

Paul
 
OP
OP
TNcowboy

TNcowboy

Full Member
Joined
Aug 29, 2019
Messages
220
Hi Paul
Timing is right on and yes I did spray for vacuum leaks and no change in idle.
#2 is slightly out of specs so I'm thinking that it might be worthwhile to adjust the valves but that doesn't explain the engine acting fuel starved under acceleration
 
Top