• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Amp meter question

Acwood04

New Member
Joined
Jun 10, 2012
Messages
15
So I've searched the forums and found some great info on the amp meter but what is happening to me isn't what I've read. My question is kinda simple, with the engine running (new 100amp tuff stuff 1 wire internal regulated alternator but made for the bronco) and I don't get a + after starting it just sits at 0 but when I turn on headlights I get the needle down to -10 or so, and it stays at -10 while the headlights are on. Turn the headlights off with the motor running and back to 0. Ive got a centec harness to my aftermarket gauge. I also notice the needle go from 0 to negative when im driving in the day with no headlights, but when the blinker is on or I'm hitting the brakes the needle drops down to the - side and when I let off the brakes and/or turn off the flasher it jumps pack to 0. So with the flashers on you see the gauge go tick, tick, tic, to the neg side while the lamps are being lit up. So should the amp meter needle dip to -10+/- when u turn the lights on and then make it's way back to 0 with the lights on as the voltage regulator picks up the need for more juice and delivers it? Or should it ride below 0 all the time you are running headlights? Or flicker to the neg side with flashers/ stop switch? I hope this isn't too much of an annoyance to more experienced people than I but I would really appreciate the help so I can use that gauge to monitor the battery draw/charge. Thanks
 

valveamp

Full Member
Joined
May 30, 2011
Messages
287
Hi. I think the answer to your problem is that you have installed a different alternator and somewhat rewired the power distribution to the rest of the Bronco. Your original alternator wiring sent all of the current through a "loop" that goes up to the dash and through the amp gauge in your cluster. The new configuration does not do that, so the amp meter only shows a negative indication when something draws current. It's time to add a volt meter to your dash and determine if the system is working properly by looking at that, rather than your amp gauge.

I added a new alternator a few months ago and my gauge does the same thing.
 

asinor

Bronco Guru
Joined
May 13, 2011
Messages
1,396
Loc.
Tulsa, OK
Hi. I think the answer to your problem is that you have installed a different alternator and somewhat rewired the power distribution to the rest of the Bronco. Your original alternator wiring sent all of the current through a "loop" that goes up to the dash and through the amp gauge in your cluster. The new configuration does not do that, so the amp meter only shows a negative indication when something draws current. It's time to add a volt meter to your dash and determine if the system is working properly by looking at that, rather than your amp gauge.

I added a new alternator a few months ago and my gauge does the same thing.

Correct.

Some 1 wire altenators do have terminals on the back or under a cover to hook a ammeter up to. Best just to switch to a volt meter.
 

Steve83

Bronco Guru
Joined
Jul 16, 2003
Messages
9,360
Loc.
Memphis, TN, USA, Earth, Milky Way
Without seeing exactly how you have the ammeter loop wired, I have to think your new wiring is the reason for your confusion. But it could also be that an ammeter isn't intuitive to most people, so you might not understand what it's showing. ALSO: even when they were new, they weren't very reliable or accurate, so no matter what it shows, it doesn't really mean anything. The movement is all you can use to guess what's happening, and that's not very much to go on, so I wouldn't worry about it. Eliminating the confusing & worthless gauge is the best move. Adding a useful one is even better. This caption explains more, and links to an album with photos of a voltmeter swap:

 
OP
OP
A

Acwood04

New Member
Joined
Jun 10, 2012
Messages
15
Yeah I've been using my MSD ignition and there is a dedicated tach wire integrated with the centec harness. There is also a volt meter line but not hooked up. I have been checkin the voltage with a multi meter and it's fine at the battery between 12.6-13.5 volts. So I can wire the amp meter to work right (on the positive side if I wire it from the two covered prongs on the back of the alternator? I'll probly hook that up to the dash and replace my auto meter amp gauge with a volt meter.... Does yours show constant draw with the headlights running?
 
Top