• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Blueprint Accessory Drive

OP
OP
J

JR12345

New Member
Joined
Mar 17, 2019
Messages
5
Loc.
Montrose, MI
My motor was just delivered today but I haven't even gotten around to asking blueprint for specs yet. I'll post back when I get to it but progress is slow at best for me right now.
Jon
 

MonsterBIlly

Sr. Member
Joined
Dec 17, 2015
Messages
461
I currently have an explorer front drive ready to install bit I have a question. I have a brand new 200amp single wire alt I just installed a few months ago. will I be able to use it, or is the mounting different. it looks very different then the explorer mounting system.
 

RODRIG3911

Contributor
Bronco Guru
Joined
Jul 9, 2007
Messages
1,019
Loc.
Tucson
Monster Billy 3G's wont work, you'll need a 4G. The mount is completely different.
 

DrLathrop

Full Member
Joined
Oct 11, 2009
Messages
297
Loc.
Fulshear, TX
Completed the swap a few weeks ago. Holy hell its a new bronco. We used the Explorer front serp setup, a new explorer compressor, flow cooler reverse water pump & some parts from vintage air to connect to explorer system. System blows cold. Turns 33” bfg mt KM2 easily. Runs 188 degrees this week with 100 plus degrees Texas heat. Modified a Ron Davis aluminum shroud to keep the fan inside the shroud. Starts first crank everytime. Blueprint did send a different distributor after we could not get the timing to stay true & ask them for an upgraded dizzy. If enough people tell them they want Explorer front serp setup then they will start offering so that you don’t have to open up a new crate motor to change parts to make it work.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Another success story! Thanks for the feedback/update.
Enjoy your worry-free (mostly anyway) driving around in the hot weather!

Paul
 

DrLathrop

Full Member
Joined
Oct 11, 2009
Messages
297
Loc.
Fulshear, TX
Paul,
Most of the needed parts from flywheel to fuel system including the SS rear tank i got from wild horses. Great doing business with you guys.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Thanks for that for sure!

So the new distributor took care of whatever issue you had. That's good to hear they took care of it. I wonder if they know what was going on with it?
By the way, was that your thread about ignition timing being all over the place from a month or three ago?

Paul
 

RG75Bronco

Jr. Member
Joined
May 23, 2010
Messages
141
Loc.
Jacksonville
I have a question about this conversion business. My vintage air is mounted on the passenger side with my alternator. Power steering is on the drivers side. I am not a fan of moving everything around, changing out my trimming chain cover and changing the water pump. What are my serpentine belt options if any? Thanks
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
I'm not sure which setups, if any, retain the A/C compressor on the passenger side. There may be some out there and those are what you'd have to source, because you'll need all pulleys to be correct, and all idlers, tensioners/adjusters to work properly with that orientation.
With the Explorer setup, there's nothing you can do and keep it Explorer. You'd be better off starting from scratch, using an aftermarket setup, or finding a factory setup with compressor on the correct side for you. With the Blueprint, you'd have to check their site to see if they have alternatives.

While there may be some that retain the compressor on the passenger side, all factory serpentine setups turn the water pump in a reverse direction
Might be something out there for you then, but you'll have to decide if any trade-offs are worth it.
Are you having trouble with your existing setup right now?

Paul
 

RG75Bronco

Jr. Member
Joined
May 23, 2010
Messages
141
Loc.
Jacksonville
Paul,
I just want to get away from the 2 belt system. I am running a 1 wire alternator at 75 amps. I get a belt squeal from my power steering sometimes. I just would like to modernize.
 

RG75Bronco

Jr. Member
Joined
May 23, 2010
Messages
141
Loc.
Jacksonville
Paul,
By the way, say that I went with the explorer set up, would the water pump be the only thing that I would have to change?
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
No, you have to change literally everything. It's all a system meant to work together and is practically unique among Ford setups.
So literally nothing (or at least almost nothing) from your original setup will work with the Explorer setup.

The system consists of basically a base/framework of two single large brackets that everything else is bolted to.
But to have all of the pulleys align you must use the water pump. To use the water pump you must use the front timing cover. To use the timing cover you remove your fuel pump eccentric. Because of that, and the fact that there is no place to mount a mechanical fuel pump, you lose that too in case you're still using a mechanical pump.

The low-profile aspects of the Explorer drive system start at the base and work their way outward from there. It's the only way to achieve such a low profile.

So, as said, items unique to the Explorer are:
1. timing cover
2. water pump
3. alternator
4. power steering pump
5. a/c compressor mounting (but you can use some other compressors)

You can mount a Saginaw power steering pump and keep the belts in alignment, but you lose the entire driver's side Explorer bracket and therefore the a/c compressor location as well.
I know of no alternate for the passenger side to run other alternators. Never been a need because the mounting system for the Explorer 4G alternator is stout and well put together. Same for the driver's side too actually, but so many people wanted an upgraded power steering pump and did not want the a/c compressor at all, so losing the left side bracket to allow a Saginaw pump installation was not hard to justify.

You'll have to come up with a different solution if your hope is to retain your current orientation then. Otherwise it's all new from the ground up.

Paul
 

Rusty_S85

Jr. Member
Joined
Aug 3, 2019
Messages
120
The explorer front dress can be made to look nice. Powder coat the pulleys, new bearings, and have someone tumble your aluminum brackets, they come out real nice.
40f19e0d46a0a58ea763fd3a5cc2397f.jpg
39dcfbbd68b49963933da4e9f5d80669.jpg
a78bf7cbf3f7470f227127ec9270056d.jpg


Sent from my SAMSUNG-SM-G930A using Tapatalk

Not sure if you corrected it yet or not, but you really need to toss that push in oil fill cap and put a filtered breather on there, without youll be pulling a vacuum on your crankcase.
 

RG75Bronco

Jr. Member
Joined
May 23, 2010
Messages
141
Loc.
Jacksonville
I have the Explorer alternator bracket, and alternator. I just have to get to the pull a part yard and look around. I have seen a few Explorers on FB Market Place cheap, and I have considered buying one to part it out, and sell the parts I don't want to others or the scrap yard. Paul thanks for your response.
 
Top