• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

brake lamp switch woes....

OP
OP
tasker

tasker

Contributor
all knowing of nothing
Joined
Jun 2, 2006
Messages
21,708
Loc.
NH
I WISH mine worked with just that!
 

ksagis

Contributor
Aspiring Bronco Guru
Joined
Jun 15, 2020
Messages
819
Loc.
Austin
It is a confusing design for sure. Feels like there are a couple things in play. Like ntqsd says, it needs some play to work. And if people have been stomping on the brakes pre hydro, the plate in the switch gets bent or misconfigured.

My setup was working fine (without a bushing). I was working to tighten up the entire linkage as much as possible and inserted a bushing, then brake lights on all the time. Swapped in new switch, works fine. I had other fish to fry and moved on. I bet there are 1,000 variations of my experience......
 

ntsqd

heratic car camper
Joined
Jan 30, 2005
Messages
5,970
Loc.
Upper SoKA
I find it rather curious that Ford used this design where the deflection distance needed to make contact is so variable, and usually a small distance, to avoid any sort of manual adjustment. And then Dodge came up with a self-ratcheting design in the early 90's that also proposed to eliminate the adjustment. Both of which I'd call failures. I've replaced one of those Dodge switches twice because eventually they won't turn on the brake lights either.
GM just made the switch adjustable. I'll guess that they held the tols of the related parts close enough that minimal to no adjustment was needed.
I'll be making that bracket in the pic above for other project vehicles I'm quite sure.
 
OP
OP
tasker

tasker

Contributor
all knowing of nothing
Joined
Jun 2, 2006
Messages
21,708
Loc.
NH
AND just to be clear, there is no busing in the eyelet now. Ordered one up to see if it will cure my problem.
 

Oldtimer

Contributor
Jr. Member with Sr. moments
Joined
Feb 4, 2005
Messages
1,802
Loc.
Sunnyvale, CA
It's been awhile since I looked at my brake switch, but my thinking was that the flat on the end of the pushrod tended to rotate around the center bushing as the pedal was depressed, and the corners on flat activated the switch.
 

serial car restorer

Yes, I'll restore almost anything...
Joined
Aug 27, 2024
Messages
742
Loc.
Western Oregon
It's been awhile since I looked at my brake switch, but my thinking was that the flat on the end of the pushrod tended to rotate around the center bushing as the pedal was depressed, and the corners on flat activated the switch.
This is how I see mine working as well. Since my truck had nothing there when I bought it (all burned in fire 20 years back), I have a new stock switch and a new pushrod (Tom's power booster), no bushing. So far it works great. Lights come on with just a small amount of pedal movement, just before the pushrod actuates the booster/master.
 

ntsqd

heratic car camper
Joined
Jan 30, 2005
Messages
5,970
Loc.
Upper SoKA
Like this: https://www.rockauto.com/en/moreinfo.php?pk=44661&cc=1105456&pt=10474&jsn=752 right?
SLS-70_Front.jpg


Since the switch has that piece of flat sheet metal that bears against the flat on the end of the push-rod and is only located by being captured on the pedal's pin by the push-rod there is nothing to prevent it from rotating around the pin with the push-rod. Were it rotationally fixed on the pin so that it stayed in alignment with the pedal, then that could work, but it is not. Or at least none of mine have ever been fixed that way.
 

Brush Hog

Full Member
Joined
Mar 16, 2022
Messages
241
Loc.
NorCal
I learned that if that switch is installed upside down (which was easier) it won’t work correctly. Also learned if the bushings aren’t installed (which was easier) it won’t work correctly. And finally I learned if the bushing aren’t installed correctly (and it was easier to install them incorrectly) it won’t work. So if anything you do to that switch seems easy try the hard way!
 

ksagis

Contributor
Aspiring Bronco Guru
Joined
Jun 15, 2020
Messages
819
Loc.
Austin
Combo of bushing and new switch? (that was the combo that worked for me with light pedal pressure with HB)
 
OP
OP
tasker

tasker

Contributor
all knowing of nothing
Joined
Jun 2, 2006
Messages
21,708
Loc.
NH
Come to find out it had the bushing..used new one anyway
 

bfoldy

Contributor
Sr. Member
Joined
Sep 13, 2004
Messages
797
Loc.
Torrance, CA
If you get tired of dealing with this in the future, as mentioned by other members above , I’d consider switching to a plunger style. I battled both the inline pressure switch and the ford style at the pedal pivot point for years and the plunger just works consistently. I have one from Painless mounted on a simple bent steel bracket under the dash.


Sent from my iPhone using Tapatalk
 

omureebe

Contributor
Sr. Member
Joined
Jun 18, 2013
Messages
419
If you get tired of dealing with this in the future, as mentioned by other members above , I’d consider switching to a plunger style. I battled both the inline pressure switch and the ford style at the pedal pivot point for years and the plunger just works consistently. I have one from Painless mounted on a simple bent steel bracket under the dash.


Sent from my iPhone using Tapatalk

e589ab6885ec6c22b25415fdc4ff36f1.jpg

These inline switches work. Always.


Sent from my iPhone using Tapatalk
 

bfoldy

Contributor
Sr. Member
Joined
Sep 13, 2004
Messages
797
Loc.
Torrance, CA
e589ab6885ec6c22b25415fdc4ff36f1.jpg

These inline switches work. Always.


Sent from my iPhone using Tapatalk

Yeah, not for me. Maybe it was due to placement on my truck (too close in proximity to headers?), but I went through 2 in about 2 years time.


Sent from my iPhone using Tapatalk
 

EPB72

Contributor
Bronco Guru
Joined
Jul 13, 2019
Messages
1,216
Loc.
Pleasant Hill, CA
Yeah, not for me. Maybe it was due to placement on my truck (too close in proximity to headers?), but I went through 2 in about 2 years time.


Sent from my iPhone using Tapatalk
Yep finding /getting one that works at low enough pressure to turn on the lights May late a couple trys,,, or having to skid to a stop to get the brake lights to come on..
 

Bitch'nBronco

Contributor
Loose Cannon
Joined
Dec 1, 2005
Messages
3,620
Loc.
Ringwood, NJ
I had to shim mine with one of these metal head unit release pins to get it to work. I slid it in, and bent it at a 90 on the top side of the switch to keep it from falling out. No problems for over a year:
1755096686587.png
 

Yeller

Contributor
Bronco Guru
Joined
Mar 27, 2012
Messages
7,692
Loc.
Rogers County Oklahoma
e589ab6885ec6c22b25415fdc4ff36f1.jpg

These inline switches work. Always.


Sent from my iPhone using Tapatalk
Jeep used those pre 1976 in their brake systems, there was a port in the master cylinder for them. They always failed. If you can get them to work and live, fantastic, most of us can’t get them to live a few weeks.
 

ntsqd

heratic car camper
Joined
Jan 30, 2005
Messages
5,970
Loc.
Upper SoKA
The VW version of those brake system pressure switches are somewhat notorious for failing, which results in a leak. The early actual VW made switches are in high demand because none of the aftermarket switches are worth anything.

When I saw that the Wagon had one of them it's removal became a priority.

If you look around you'll see that no one does brake light switches like that any more, and haven't for a couple of decades. There's a good reason why.
 
Top