• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

braking system issues

OP
OP
M

mduenas

Sr. Member
Joined
Dec 29, 2015
Messages
511
Loc.
Los Angeles
You are getting good advice on what it could be but I think you need to narrow it down. I would verify the lines are routed correctly which it sounds like you did (disc brakes get the big reservoir).

I would take the rear line out of the master cylinder and plug it (you can get a plug online, Home Depot, Advance Auto etc). Then take it for a test drive carefully. If your front brakes are good they should stop you with no problem. If they work poorly I would suspect something else is wrong in the front (prop valve, line kink, air trapped, wrong or bad m/c). But if they work great you know your problem is in the rear half of the system. It could still be the prop valve or the m/c but at least you know your front half is solid.

Great idea! And for that I’m assuming I don’t have to bleed the brakes?
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Good luck on getting out of that work!
Actually, sometimes you do get away with it. But officially anytime you open a brake system line, you potentially need to bleed at least that part of the system.
Removing a fitting from the master at least puts any potential air intrusion to a minimum, and way up top where it may actually purge itself.
But you can't count on it...

Paul
 

ntsqd

heratic car camper
Joined
Jan 30, 2005
Messages
5,970
Loc.
Upper SoKA
Find my post on a do it yourself vacuum bleeder that uses an old peanut butter jar and engine intake vacuum. Makes bleeding brakes SO much simpler and easier!
 

lbuch40

Contributor
Full Member
Joined
Oct 6, 2013
Messages
158
Loc.
Black Hills
Yeah, it's the same style we sell as a standard proportioning valve. I think everybody sells them nowadays, and probably from the same three or four companies.
I've had defective ones before, including one that made the front brakes drag.
Maybe they'll replace it for you if you are diligent in your testing to make sure it could only be the prop valve?
Still sounds like at least part of the issue is something else though.

One thing about part of your issue, is your left/right problem with only one tire locking up. This type of issue at the rear can't be caused by anything forward of the hard lines on the axle housing. Nothing up front, from the soft hose to the frame, all the way up to the master cylinder can cause one side to brake harder than the other. That can only be done by some malfunctioning part, or inconsistent assembly or adjustment.
My point is that everything in front of the hose to the axle would effect both brakes equally. So the fact that only one wheel is locking up (as opposed to both) means the problem is only at the back axle.

Now, that's just the side-to-side issue. The problem with the rear having more power than the front is another matter.
For a proportioning valve, I like using an adjustable one in the rear system only. One like these: https://www.wildhorses4x4.com/category/Bronco-Proportioning-Valve effects only the rear.
But both equally, so you still have to deal with the one side braking harder than the other.

Do you still have the original H-block that was mounted to the frame? If so you can reinstall it, plumb the lines back to it, and then test the brakes. There is no restriction with an H-block to cause trouble. It's just a distribution block and the ports pass straight through.
They are still worth checking out before installing however. Water can get in and cause corrosion, as well as other things happening to them probably. Make sure it's perfectly good before installing.

Depending on the size of the fittings down at the current proportioning valve, there may be a simple threaded coupling that can mate the two halves together to bypass the prop valve. I just don't know the thread sizes or if there is such a thing as the coupler without you having to make one yourself.
Maybe someone has done this before. But the H-block would be the easiest to make work I would think. So if you have one, start there.

I suppose if you're not against spending a little more money (when does it stop?) you could have a hose made that runs from the master all the way down to the frame without stopping for any other components.
S
Maybe some others will come up with a simple solution. Probably someone's done it.

Paul

Still working on my issue with the dragging front discs. I also have the passenger rear drum brake that will lock up when braking hard. But I am relatively sure that is a result of contaminated brakes from leaking axle seal. I recently discovered that the breather for the rear axle was completely plugged, therefore building pressure and pushing gear oil out the passenger axle seal.
 

Lunar-tic

Sr. Member
Joined
Sep 28, 2009
Messages
629
Loc.
Brentsville
I know this is a late response to this thread, I was researching another issue and ran across this. Did you get it sorted out? Looking at your lines at the master cylinder (after upgrading to power brakes myself), I think they are backwards. My apologies if I am having a Captain Obvious moment.
 
Top