• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Carb questions

KANE

Sr. Member
Joined
Feb 15, 2007
Messages
489
Loc.
Pembroke, MA.
Been a while, hope everyone is well!
I’ve had a great running 351 mildly built with a Holley 4160. Today all of the sudden it started to run rough and died. I was able to restart if I held the gas to the floor. Runs good for a minute and then died. Got it home and realized it was rich as hell and overfueling. The gas was coming outta the front air bleeder then die. All the while stinks like raw fuel.
I tried cleaning the bleeders to no avail. Pulled the screen on the fuel inlet, cleaned and same thing.
So my thoughts are, treat to a new carb...just because this is 20 years old and while it ran well, I always thought it could run better. So, What would suit my motor best?
Second, do I rebuild? Or is this the beginnings of other adjustment nightmares?

Or could it be something more obvious??

As always look forward to your input and thank you!
 

Pa PITT

Contributor
Bronco Guru
Joined
Jul 15, 2005
Messages
11,300
Loc.
Stephenville TEXAS
.. SOMETHING MORE OBVIOUS . MY GUESS. dirty fuel at some point .
.. IF YOU FEEL IT'S GOT TO BE IN THE CARB . the take it apart & clean & just put it back together.
... But of course some times you ruin one gasket that just can't be found.
 

TNcowboy

Full Member
Joined
Aug 29, 2019
Messages
220
Sounds like a dirty, or more likely, bad needle and seat.
20 years old? Good opportunity to rebuild it. Do a thorough cleaning...use an ultrasonic cleaner if you have access to one. If not Chem-dip is fine
 
OP
OP
KANE

KANE

Sr. Member
Joined
Feb 15, 2007
Messages
489
Loc.
Pembroke, MA.
Yeah I’m gonna clean it for sure. Removed the needle and the Oring seems not so plump. Gonna try to get the oring today and clean the rest.
 

SHX669

Bronco Guru
Joined
Jan 9, 2009
Messages
1,997
As mentioned ; I always make sure I have all the gaskets I MIGHT need before I tear into the carb . Decrease the down time in the event a gasket gets damaged.
 
OP
OP
KANE

KANE

Sr. Member
Joined
Feb 15, 2007
Messages
489
Loc.
Pembroke, MA.
Ok she’s all set! I bought a Holley rebuild kit at AutoZone and just installed the needle and good to go! Also gave the bowls a few love taps. Once it was good I seafoamed the carb and smoked out the neighborhood.
Thx for the direction
 

Rustytruck

Bronco Guru
Joined
Feb 24, 2002
Messages
10,872
When i use to use that Holley it mostly ran on the primary side so the secondary side would hang up and flood over. you have to run them often hard to get into the secondary side and keep them operation properly. Baby them and eventually it gets gummed up and floods. especially bad running up hill on bumpy mountain trails. when you get fed up with it use a quadrajet.
 

Mikey

Bronco Guru
Joined
Aug 15, 2001
Messages
1,480
The small rubber O ring on the needle assembly routinely dries out and floods the Holley out so I keep a handful of those O rings handy. I flood out, swap out the O ring and good to go in a few minutes. I have a Holley on both the 74 Bronco and the 68 Cougar. Been messing with Holleys for 40 years....kinda a love hate relationship.....I do like my Holleys!
 

Mikey

Bronco Guru
Joined
Aug 15, 2001
Messages
1,480
Except now I have the 2 piece needles in my Truck Avenger Holley on the Bronco.....doh! Have to pull the bowls on those.
 

BroncoJimbo

Contributor
Long-term owner
Joined
Jun 11, 2014
Messages
291
Loc.
North GA
That used to happen to me quite a bit with my old 4160. I got pretty good at pulling the needle out and cleaning it on the side of the road. Solved that problem by going with a Truck Avenger. Has not happened since.
 

jckkys

Contributor
Bronco Guru
Joined
Mar 15, 2012
Messages
5,221
That's interesting. The Truck Avengers use the same float bowls as other 4150s and 4160s. They're interchangeable. Also in the last 60 yrs. of working with Holleys, the O rings were never a problem. Swollen or cracked gaskets were. However the blue ones are better.
 

nvrstuk

Contributor
Just a Bronco driver for over 50 yrs!
Joined
Jul 31, 2001
Messages
10,622
Loc.
PNW
" Also in the last 60 yrs. of working with Holleys, "


How old ARE YOU jckkys?? :)
 

jckkys

Contributor
Bronco Guru
Joined
Mar 15, 2012
Messages
5,221
Power valves are just a diaphragm and spring there's nothing to "get stuck". Every carburetor has a power enrichment circuit. Fords, and Holleys have power valves. The others like AFBs and Q-junks use metering rods that have pistons that do get stuck.
Before nvrstuk gets concerned about various member's age it may be more helpful to know their location and what year EB they're working on.
 

nvrstuk

Contributor
Just a Bronco driver for over 50 yrs!
Joined
Jul 31, 2001
Messages
10,622
Loc.
PNW
... no humor anymore? Did it disappear over the last 60 years while working on Holleys? :)

Trying to enjoy life a little.
 
Last edited:

nvrstuk

Contributor
Just a Bronco driver for over 50 yrs!
Joined
Jul 31, 2001
Messages
10,622
Loc.
PNW
When the diaphram gets inverted or a hole it's what's commonly called "stuck" because it's stuck in a position that doesn't allow it to work anymore.

Qjets metering rods get stuck when they haven't been used for 5 yrs at a junk yard. Never seen a qjet that works or has worked within 6 months of having stuck metering rods.

Pulled more than a few Holley's apart that have "blown" pwr vavles... diaphrams don't like sudden air movement amd tear or invert. A tear or hole is quite common on Holleys. Ask someone who's worked on Holleys... ask all those Chebby guys - - as it's a common complaint.

I am not saying this is the cause for this OP's problem.

What Madgyver said. Fuel coming out the top of the bowl is usually a needle/seat issue if this is a new symptom and the vehicle has been running properly before.
 
Last edited:
Top