• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Carburetor Adjustment

broncosam

Bronco Guru
Joined
Feb 8, 2005
Messages
1,188
Holley carb on my Bronco is set too rich and needs adjustment. Been doing some research on using a vacuum gauge to get it set, watched a bunch videos on this subject on YouTube. But it's bit confusing. One video will say hook the vacuum gauge to ported vacuum and another will say hook it up to un-ported manifold vacuum. Is one better than the other and will let me tune the carb better.
 

B RON CO

Contributor
Bronco Guru
Joined
Jun 29, 2016
Messages
2,484
Loc.
Statesville, NC
Hi, before adjusting the carb the ignition must be 100% tuned up, including the ignition timing.
You should have a clean, non restrictive air filter.
The only adjustment you can do is the idle mixture and idle speed.
If the engine is running rich all the time you have to change to smaller jets.
Good luck
 

jckkys

Contributor
Bronco Guru
Joined
Mar 15, 2012
Messages
5,221
More information would help. What model Holley is it? In the tuning process I run 2 vacuum gauges to see both ported and full vacuum. There's also a wide band A/F gauge and a tach. Running rich can be caused by several maladjustments, choke. float level, jets, incorrect power valve, etc.
 

DC_Gearhead

Sr. Member
Joined
Dec 28, 2015
Messages
660
You should watch the videos on YouTube from thunderhead289 on adjusting Holley carbs. He’s a normal guy that explains things with logic.

Biggest learning I had from him?....get the carb back to factory settings and adjust from there. I used to think Holley carbs were part magic and part experience. Not anymore.


Sent from my iPhone using Tapatalk
 
OP
OP
B

broncosam

Bronco Guru
Joined
Feb 8, 2005
Messages
1,188
When the engine is warm and idling in my garage the exhaust fumes are real strong, inside of the exhaust pipes are black. I haven't had this Bronco long, just did a good tune-up. Engine sounds smooth, has good throttle response with no hesitation. As far as timing goes I'm pretty close to factory spec. Was told by the PO that he thought it had a mild cam in it, and at idle it does sound like it. BTW, I do keep the overhead door open to keep from gassing myself.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
What carburetor exactly?
No matter how rich the exhaust smells, a cam is at least a big part of the issue. Some are jetted rich just for the cam, some act rich just because of the cam, some burn rich because of a weak ignition as mentioned, and plenty of other stuff.
Especially at idle.

Would not hurt for you to play with timing, play with engine idle speed (again, because of the cam) and check the manifold vacuum level to see where it is (again, because of the cam).

Paul
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,111
Was it ever right to start with? What happen to make it need adjusting? Are you sure the choke isn't sticking closed?

You might just need half a can of carb cleaner to blast through the vents and air bleeds. I've owned carburated engines that are decades old that still don't need adjustment. Sometimes a blast of carb cleaner, but if it was running good before there is no reason to need adjustment now.

But if you have changed something, or it has never run right, that is where adjustment is needed.
 
OP
OP
B

broncosam

Bronco Guru
Joined
Feb 8, 2005
Messages
1,188
What carburetor exactly?
No matter how rich the exhaust smells, a cam is at least a big part of the issue. Some are jetted rich just for the cam, some act rich just because of the cam, some burn rich because of a weak ignition as mentioned, and plenty of other stuff.
Especially at idle.

Would not hurt for you to play with timing, play with engine idle speed (again, because of the cam) and check the manifold vacuum level to see where it is (again, because of the cam).

Paul

Paul the numbers on the carb are 80457-8 under that is the number 0351
Thanks
 

jckkys

Contributor
Bronco Guru
Joined
Mar 15, 2012
Messages
5,221
The List#80457 is what Holley calls a universal carb. It's 600 CFM and very similar to the 1850s, their first 600 CFM universal carb. All universal carbs are set up a little rich, but broncoam's is very rich. The power valve should be 6.5"Hg. The primary jets were 69s originally. That's a start at returning it to original. The set up specs would be included with a rebuilding kit, another guide to return original configuration.
 
Top