• Just a reminder that you won't be able to start new posts or reply to existings posts in the Archive forum.

    This is where all the old posts go so they can still be used for reference and searched.
  • Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Cleaning frame

daddycreswell

Contributor
Bronco Guru
Joined
Jul 30, 2011
Messages
2,854
Loc.
Lebanon, TN
I'm thinking before winter I am going to try and clean up my frame some and maybe shoot some undercoating on it. It's pretty nasty under there. I know pressure washer is the way to go, and maybe some simple green maybe, or another de-greaser? Then take a wire brush to get at any surface rust then undercoat or do I prime it before? Thanks
 

Crawdad

Bronco Guru
Joined
Feb 16, 2011
Messages
3,635
KBS has a great paint 3 step system for such frames. It comes with a cleaning solution or you can use Royal Purple (that tidbit was given to me by a bronco builder).
 

O2sled

New Member
Joined
Jul 27, 2009
Messages
24
Loc.
Cheyenne
I used some "oven cleaner" on my frame from Sams Club that worked great, just sprayed it on and pressure wash off the heavy grease. It comes in a 2-pack and has a squeeze trigger that when it sprays it foams so that it will cling to the vertical surfaces. Only draw back I found was it made the skin tingle a little if you get it on you, wear gloves and on the bare surfaces it would rust soon after drying.
 

spap

Bronco Guru
Joined
Jan 2, 2010
Messages
2,642
Wire brush on a hand held grinder, power wash didn't do much for me got the loose stuff off
 

bronconut73

Bronco Guru
Joined
Aug 7, 2012
Messages
9,919
I used some "oven cleaner" on my frame from Sams Club that worked great, just sprayed it on and pressure wash off the heavy grease. It comes in a 2-pack and has a squeeze trigger that when it sprays it foams so that it will cling to the vertical surfaces. Only draw back I found was it made the skin tingle a little if you get it on you, wear gloves and on the bare surfaces it would rust soon after drying.

Me too.
The commercial oven cleaner I used was in a one gallon jug with a hose and sprayer.
I even remember the name. Jeffrey's or Jeffries oven cleaner. Yes it burns the skin and eyes. Be prepared for that.
It is wicked strong. That and a pressure cleaner is the ticket.

I did mine just like this back in the 80's. Mine had Rusty Acres name brand under body coating everywhere. It was a popular underbody coating back in the 70's and 80's. It was ugly but did it's job because there was little if any rust "where" it was sprayed. That oven cleaner loosened it up so I could scrap the tough stuff off with putty knives and wire brushes. A final oven cleaner spray down on the scraped and brushed surface was allowed to sit for a little bit then blasted with the pressure cleaner.
Worked good.
 

BluebroncoNC

Bronco Guru
Joined
Jul 30, 2007
Messages
1,768
Loc.
Asheville, NC
Surface rust I used a mild acid, muriatic acid to cut it, then por-15'd the underside.. um, make sure you hose off the acid and dry the frame before continuing with the por-15.
 

Attachments

  • 01-06-2013 01;51;09AM.jpg
    01-06-2013 01;51;09AM.jpg
    141.2 KB · Views: 162
  • 01-06-2013 01;52;40AM.jpg
    01-06-2013 01;52;40AM.jpg
    123 KB · Views: 162
  • 01-06-2013 01;56;01AM.jpg
    01-06-2013 01;56;01AM.jpg
    109.2 KB · Views: 153
  • 01-06-2013 01;56;32AM.jpg
    01-06-2013 01;56;32AM.jpg
    97.1 KB · Views: 124

a74ranger

Full Member
Joined
Jul 6, 2004
Messages
258
Loc.
Athens, GA
I used the KBS system and it worked well. As the label says, if you get the coating on your akin, the only thing that will remove it is time.
 

cldonley

Contributor
Bronco Guru
Joined
Jul 4, 2011
Messages
1,398
Loc.
Robinson, TX
Easy-off works pretty well, but it's expensive. I like the muratic acid idea. It's cheap and I've used it prior to painting concrete floors to degrease. Works like a champ.
 

nickgp

Bronco Guru
Joined
Jan 17, 2010
Messages
1,024
Zep Purple Degreaser. Comes in a gallon jug at Home depot or Lowes. Sprayed it on full strength w a hudson sprayer. Let it bake in the sun, scrubbed, scrapped and pressure washed it. Repeat. . It worked very well, in fact, it took off alot, if not all of the factory coating. Frame is ready to be blasted now. Before this, i did the easy off and auto store degreaser. The Zep was by far the best. Paid about 12 bucks for the gallon.
 

u10072

Bronco Guru
Joined
May 18, 2007
Messages
2,249
If you have any really bad crud on the frame -tar/undercoater- you are going to need to mechanically clean it. On the frame I gotta go with a 4 1/2" grinder and about 10 wire wheels. Once all the crap is off you then degrease it -- cans of oven cleaner get very expensive. Just power washing in my experience doesn't really get it down to the metal on the frame and the paint on the undercarriage when the gunk is oil-based. I am an undercarriage clean freak and have done this filthy-dirty-terrible but well worth it dance step numerous times with about as close to sandblasted results as you can get.
 
Top