• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Clutch fork questions

KyleQ

Bronco Guru
Joined
Apr 24, 2008
Messages
5,480
I've got a tab style bell currently in the truck and I've got an aluminum hydro bell in the barn.

I'm at a loss on to what happened to my clutch this weekend - I've got all of the clutch brackets properly mounted, I've even got the EFI clutch mount bracket installed. It's very solid -

I can adjust the linkage multiple times and it still goes to the floor. It seems to want to go back and up at an angle and its like its falling off the TOB or something. If I pull down on the fork and push back it seems like its there, but it doesn't even work once after I put it back together.

I ran into this before - but I replaced the TOB and I was good. I'm curious - what all does the fork pivot off of? I can nearly pull the clutch fork out of the side of the transmission right now. I understand the end clips onto the TOB and the clip mid way on the arm goes through the tab on the bell housing, but there is a ball with tabs over it - what does that pivot off of?


I'm going to convert over to a hydraulic setup - I'm going to run the How slave and Wilwood master and fab a mount off the transmission so it isn't a waste of time. I want to figure out why the clutch fork is doing what it is doing so it doesn't happen on my next trip out. Anyone run into this?

I'll take some pics and video tomorrow-

Thanks-

Kyle
 
Last edited:

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
It pivots off the bracket that the clip on the fork slips thur. If the tab on the bellhousing is loosen that may be the issue or your clip on the fork has broken and is allowing the fork to move around.
 
OP
OP
KyleQ

KyleQ

Bronco Guru
Joined
Apr 24, 2008
Messages
5,480
Ok - so that captured ball picots off that tab? Hmmm... - I'll have to take some pics.
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
If you have a ball type then it should more or less snap in. Unless the tabs that hold it there are broken or the ball pivot is bent or something. Im not real sure when the ball type was used. I usually see the clip type or wire bail type both of which pivot off a bracket like this. This is the clip type the wire bail looks similar will have cutouts for the wire bail on the endges and no hole in the center.
 

Attachments

  • CF tab.jpg
    CF tab.jpg
    41.9 KB · Views: 69
OP
OP
KyleQ

KyleQ

Bronco Guru
Joined
Apr 24, 2008
Messages
5,480
Is it possible I have the wrong fork in there? I pieced this kit together - my bell does have that on there. It is not the bailing wire type.

JBG shows this - I can't tell if there is a ball on the other side or not.
NEW8CLYCLUTCHFORK.JPG


Should it even have a ball on the fork?
 
OP
OP
KyleQ

KyleQ

Bronco Guru
Joined
Apr 24, 2008
Messages
5,480
My clutch fork looks like this-
280081d1388611158t-1983-f150-np435-clutch-fork-help-hpim7042.jpg

It has an actual ball in there - where it clips on and where the ball sits seems to be totally wrong for any type of leverage...

Oriley shows this for the 74' Bronco - no ball.
14552-002.jpg
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
Ive never seen that type with the ball I would imagine that the ball may just be to help hold the tab in place. On the bracket that I posted. Of course the only place for leverage is against the sheetmetal bracket. It could be worn or bent and could be the cause of your issues.
 
OP
OP
KyleQ

KyleQ

Bronco Guru
Joined
Apr 24, 2008
Messages
5,480
I'm going to order a replacement - probably the hydro conversion stuff at the end of this week. At least it fell apart before I hit the mud pit....
 

Sagacious1971

New Member
Joined
Jul 7, 2017
Messages
1
Clutch Fork Update

New to site. I have a clutch fork like the dirtier one on the right. It is broken like the one in the picture. Is there a way to update to a newer style or find one like the dirty one on the right? Shop and I are having a heck of a time. Thank you in advance for your help.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Hey Sagacious. Welcome to classic! Sorry you're having so much trouble.
The only style I've ever used is like the third one (in the bottom pic listed for '74) and that's the only style we have available (http://www.wildhorses4x4.com/product/Clutch_Fork_Clip_Style_New/Early_Bronco_Clutch) but I don't know if that's just all that we've bothered to carry, or if the others just are not available anymore.
It's properly mated up to the bell-housing bracket that broncnaz posted up. Which was also available last time I checked.

Now the question is, whether or not the hole pattern is the same from one style to the other, so you can retrofit whatever is still available.
I don't know that, but maybe others here have tried. They "look" to be the same, but could be off by just a tiny amount to not let them work.

It's actually a very common failure point. Some kits come with rivets like the factory did, and some come with screws and locking nuts. I've done the rivets and they worked just fine, but I prefer the screws-n-nuts myself.
You might find these same parts (or even the ones like yours) at the Mustang sites. Even though these were trucks built on the truck assembly line, many of the engine parts interchange to the cars quite often.

Good luck.

Paul
 
Top