• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

D44 Assembly

Okie69

Contributor
Sr. Member
Joined
Nov 28, 2011
Messages
842
Hi all,

I've found a local shop to put together my HP Dana 44 which is fantastic as they are literally 1/4 mile away from my house. He asked that I get all of the parts and pieces together and then he would handle the assembly.

The question is, what the easiest way to get everything I need? I've got a list going but I'm not sure on all of the bolts that hold the spindle and hub together for instance. I've started a list of things I think I'll need.

WARN PREMIUM LOCKING HUBS 30-SPLINE OUTER FOR USE WITH DANA 44 Item #: 8891 (Wildhorses)

4340 CHROMO AXLES W/SPICER 760 JOINTS FOR USE WITH 66-77 BRONCO DANA 44 Item #: 8681NET (Wildhorses, The passenger side axle shaft has went missing at some point through the years so I might as well upgrade. Also, does being a HPD44 out of a late 70s ford make a difference in what I'll need for U-joint size etc?)

DANA/SPICER BALL JOINTS UPPER & LOWER
Item #: 8823 (Wildhorses)X2

This is wear it starts to get a little muddy. I am planning on replacing all seals, races, bearings etc while it's apart. Is there a better way to get all of this than buying them piece by piece? As you can probably tell I'm a novice, but trying! any advice or info is greatly appreciated, and thanks for taking them time to read all of this! I've attached a few pictures of what I have. The differential itself is all put together and looks to be in great shape (Thanks U10072!) so I'm not worried about that.
 

Attachments

  • D44-1.jpg
    D44-1.jpg
    119.3 KB · Views: 126
  • D44-2.jpg
    D44-2.jpg
    159 KB · Views: 119
  • D44-3.jpg
    D44-3.jpg
    134.5 KB · Views: 122

mrdrnac

Contributor
Sr. Member
Joined
Feb 6, 2010
Messages
577
First question, are you going to use the HP axle full width or are you shortening the passenger side by 6" to make it Early Bronco width? The axles you have listed are the Early Bronco ones.
 
OP
OP
Okie69

Okie69

Contributor
Sr. Member
Joined
Nov 28, 2011
Messages
842
First question, are you going to use the HP axle full width or are you shortening the passenger side by 6" to make it Early Bronco width? The axles you have listed are the Early Bronco ones.

Sorry, I definitely should've included this is the initial post. It has already been shortened to EB width.
 

Attachments

  • D44-4.jpg
    D44-4.jpg
    88.3 KB · Views: 154
  • D44-5.jpg
    D44-5.jpg
    75.8 KB · Views: 144

Bronconut

Full Member
Joined
Jun 15, 2002
Messages
278
Couple things to consider/validate:
1. The Warn hubs you list are for 30 spline outers, the axles you list require 19 spline.

2. While the early Bronco axles will work in the narrowed housing, chances are the driver side is still full size width. If you are buying new axles, get the full width inner for the driver and EB width for passenger. That way you are maximizing spline engagement.

3. Most drivetrain vendors, including the Bronco vendors, sell complete axle rebuild kits with bearings and seals.

4. The spindles on your knuckles look to already have studs for the spindles installed, which means you should only need ten, 3/8 fine thread all metal lock nuts to install.

5. Now is a good time to upgrade your differential if that tickles your fancy.

Just a few thoughts,
Mike
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
...The differential itself is all put together and looks to be in great shape (Thanks U10072!) so I'm not worried about that.

Yes, but aside from what the others have said, being already put together means you get to take it all apart if you're needing to replace bearings and seals.
If you mean that it's freshly built, then you don't need anything inside at all, and the only seals you will be dealing with are at the backside of the spindle and the wheel bearing hub.

Did U10072 also do the shortening? Ask exactly what was done to get it to EB width. I should be able to tell by looking at it by now, but can't really tell at a glance if the driver's side is stock full-size width still, or has also been modified.
Easy enough for one of the others that work with these a lot to know though.

Paul
 
OP
OP
Okie69

Okie69

Contributor
Sr. Member
Joined
Nov 28, 2011
Messages
842
Couple things to consider/validate:
1. The Warn hubs you list are for 30 spline outers, the axles you list require 19 spline.

2. While the early Bronco axles will work in the narrowed housing, chances are the driver side is still full size width. If you are buying new axles, get the full width inner for the driver and EB width for passenger. That way you are maximizing spline engagement.

3. Most drivetrain vendors, including the Bronco vendors, sell complete axle rebuild kits with bearings and seals.

4. The spindles on your knuckles look to already have studs for the spindles installed, which means you should only need ten, 3/8 fine thread all metal lock nuts to install.

5. Now is a good time to upgrade your differential if that tickles your fancy.

Just a few thoughts,
Mike



Thanks for the info!

1. Yep sure are didn’t notice that.

2. If it is narrowed on the driver side will the full width still work? I think I read that there’s like .625” difference is all. I have the driver axle that was provided when I purchased this setup I’m sure I could measure and see what it is setup for at the moment.

3. I didn’t see one yet, but I’ve only looked at a couple of the vendors so far. I’ll keep at it.

4. Awesome! Easy enough.

5. I would love to but right now I’m in just want to drive it and enjoy for awhile mode since it has been off of the road since ‘12
 
OP
OP
Okie69

Okie69

Contributor
Sr. Member
Joined
Nov 28, 2011
Messages
842
Yes, but aside from what the others have said, being already put together means you get to take it all apart if you're needing to replace bearings and seals.

If you mean that it's freshly built, then you don't need anything inside at all, and the only seals you will be dealing with are at the backside of the spindle and the wheel bearing hub.



Did U10072 also do the shortening? Ask exactly what was done to get it to EB width. I should be able to tell by looking at it by now, but can't really tell at a glance if the driver's side is stock full-size width still, or has also been modified.

Easy enough for one of the others that work with these a lot to know though.



Paul



I can shoot pictures of anything particular that might help. Just let me know. It looks freshly built to me and everything is feels solid. I don’t plan on touching anything in the diff. I just meant bearings and seals on the ends. (This is all coming from the basic knowledge of the axle assembly I’ve gained by looking at exploded views and reading

I believe he did so the shortening. I sent him a message asking just that. I’m sure he will reply when he see it.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
1. Yep sure are didn’t notice that.

The spline count often catches people off guard.
Early 44's such as in old Jeeps had 19spl inners and outers.
Later 44's such as found in Broncos and most other vehicles of that vintage kept the 19spl outers, but went to the stronger 30spl inners.
RCV replacement axles also use 30spl outers, hence the availability of the Warn hubs made for that.

3. I didn’t see one yet, but I’ve only looked at a couple of the vendors so far. I’ll keep at it.

Most of us will carry a master kit for the INNER parts for the differentials, such as bearings and seals. But that only handles what's inside the pumpkin.
For just the wheel bearings and seals, we have this: https://www.wildhorses4x4.com/product/Wheel_Bearing_Kit/bronco_Dana44
(edit: not to worry about the application, as Ford used the same wheel bearing and seal combination from sometime in '69 all the way to '89)

But if you also don't have the bearing adjusting and lock nuts, it's a separate kit here: https://www.wildhorses4x4.com/product/Spindle_Nut_Kit/bronco_Dana44
Does one side only, so two are needed if you don't have any.

I'm guessing the reason that a company like WH does not put together full kits is the lack of demand. Yes, it's easier to buy the stuff that way, but for 99% of Broncos, all of those parts are just not needed. Most of them last the life of the vehicle.
As we deal more and more with missing parts and purchased pre-existing projects (pile-o-parts-in-a-box) this stuff comes up. But it's still not often in the overall scheme of things.
Properly maintained wheel bearings and those adjusting nuts can last the life of the vehicle.

That's my take on why we don't have full kits at least. Just for the differential itself, but not the rest yet anyway.

Paul
 
OP
OP
Okie69

Okie69

Contributor
Sr. Member
Joined
Nov 28, 2011
Messages
842
The spline count often catches people off guard.
Early 44's such as in old Jeeps had 19spl inners and outers.
Later 44's such as found in Broncos and most other vehicles of that vintage kept the 19spl outers, but went to the stronger 30spl inners.
RCV replacement axles also use 30spl outers, hence the availability of the Warn hubs made for that.



Most of us will carry a master kit for the INNER parts for the differentials, such as bearings and seals. But that only handles what's inside the pumpkin.
For just the wheel bearings and seals, we have this: https://www.wildhorses4x4.com/product/Wheel_Bearing_Kit/bronco_Dana44
(edit: not to worry about the application, as Ford used the same wheel bearing and seal combination from sometime in '69 all the way to '89)

But if you also don't have the bearing adjusting and lock nuts, it's a separate kit here: https://www.wildhorses4x4.com/product/Spindle_Nut_Kit/bronco_Dana44
Does one side only, so two are needed if you don't have any.

I'm guessing the reason that a company like WH does not put together full kits is the lack of demand. Yes, it's easier to buy the stuff that way, but for 99% of Broncos, all of those parts are just not needed. Most of them last the life of the vehicle.
As we deal more and more with missing parts and purchased pre-existing projects (pile-o-parts-in-a-box) this stuff comes up. But it's still not often in the overall scheme of things.
Properly maintained wheel bearings and those adjusting nuts can last the life of the vehicle.

That's my take on why we don't have full kits at least. Just for the differential itself, but not the rest yet anyway.

Paul



I was just looking at both of those listed kits thinking that looked like what I need.

So I get those kits.
Figure out the axle situation.
Get some nuts for the spindle assemblies.
Find the correct locking hub.

From what I’m finding it looks like that’s about all I need to get the axle together.

Also, while I’m here. I just want to say thanks for all of the information you provide on this site. You have no idea how many times your posts have been the one to lead me to a solution while scouring the forum archives.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Thanks. Appreciate the good words. Happy to help.

And don't forget the bearing grease!;D
Also, there is a very specific adjustment procedure for the wheel bearings that is not just a simple "tighten till it feels good and lock it down" kind of thing.
When you get to that point, if you don't have the service manual, let us know and we can walk you through it.

Always something... Right?%)
Good luck with the axle shaft lengths.

Paul
 
OP
OP
Okie69

Okie69

Contributor
Sr. Member
Joined
Nov 28, 2011
Messages
842
Now onto the next set of questions, I'm going to try and keep it all in this thread instead of starting new.

1. The new HP D44 has discs (pics above) will I be able to use any of the steering components off of the D30 in this new setup? I assume they're not going to be bolt up, but hoping for some interchangeability.

2. The disc brakes. Can I get by with adding a proportioning valve and adjusting accordingly for now? Then I would go to a booster setup sometime in the future. This rig is just going to be a Sunday cruiser for now so I can enjoy it a little.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
1. The new HP D44 has discs (pics above) will I be able to use any of the steering components off of the D30 in this new setup?

Yes, you can re-use your Bronco tie-rod, but will need to "adapt" the rod ends to the larger tapered holes with something like these: https://www.wildhorses4x4.com/product/Tapered_Sleeves_for_F150_Knuckles/Custom_tie_rods
While a stock tie-rod is not wide enough to fit into a pair of '76/'77 knuckles, it's wide enough to fit into the full-size truck knuckles.

The steering linkage is decent, but not as robust as other options. In case you install larger tires you can upgrade with several different options later.
Just make sure that whoever you're buying from knows you have F150 knuckles, or else be sure to retain the tapered shims.

2. The disc brakes. Can I get by with adding a proportioning valve and adjusting accordingly for now? Then I would go to a booster setup sometime in the future. This rig is just going to be a Sunday cruiser for now so I can enjoy it a little.

You do not "need" power assist. If your brakes are satisfactory now, they will be with the discs. But if you're going with larger tires at the same time you may find the brakes lacking.
What size tires will you be using?

You don't actually need the proportioning valve either, but it's a good idea. Especially the manually adjustable type that can be potentially better tuned to your truck.
I like our Moab kits because of the brackets (https://www.wildhorses4x4.com/category/Bronco-Proportioning-Valve), but you can certainly save money by mounting it yourself.

Paul
 
OP
OP
Okie69

Okie69

Contributor
Sr. Member
Joined
Nov 28, 2011
Messages
842
The steering linkage is decent, but not as robust as other options. In case you install larger tires you can upgrade with several different options later.

Interesting, but I would assume it will be tough enough to handle some in town driving.

You do not "need" power assist. If your brakes are satisfactory now, they will be with the discs. But if you're going with larger tires at the same time you may find the brakes lacking.
What size tires will you be using?

The old drums didnt seem horrible when they were working correctly, but since Ive got the disc equipped axle...

I've got 35s now (hence the exploded D30) and i'm going to be keeping them.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Interesting, but I would assume it will be tough enough to handle some in town driving.

Absolutely. For the time, the Bronco had some of the heaviest duty steering links. But they're borderline when the tires get big and you're in 4wd.
The street is not an issue for reliability, but depending on the setup (wheel backspacing, width and tire size) some flex in the linkage can become an issue.
By "issue" I don't mean it's dangerous or likely to break. I just mean that with flex you never get that perfect tight feel.

The old drums didnt seem horrible when they were working correctly, but since Ive got the disc equipped axle...

Roughly the same power (maybe a tiny bit more, depending on the pad compound) but more reliable and consistent stopping with the discs.
Power is not needed just because they're discs (I have manual Ford discs on my '71 and they're great) but the larger tires add a whole new level of need.

I've got 35s now (hence the exploded D30) and i'm going to be keeping them.

I'd say go power while you're thinking about it. You can certainly try them in manual mode without skipping a beat, then add the power boost later if you decide you need to.
Because you have the drums with the 35's you know pretty much how much power you will have at your foot's command. But just from what others have said over the years, I think 35's are just "better" with a little more oomph under your foot. Discs or not!
It's not so much for the general driving, as much as for that one time when you reeeeely need some quick and easy braking.
Or for when someone else is driving your Bronco maybe?

Either way though. Like I said, you can do the discs as a stand-alone feature and not even worry about a prop valve or booster. They will work without them. Even with discs, Ford offered the power booster as an option, not standard equipment. I know of several EB owners with manual disc '76's and '77's and a few full-size truck owners all the way to '79 with manual brakes.

If you feel you'd still like more, then consider the power assist as a separate thing and add it by itself afterwards.
If you just want to do once and not be bothered to do more work on brakes down the road, then I would definitely just plan to add the assist. I love manual brakes, but with 35's I think you'll benefit from boost.

Paul
 
OP
OP
Okie69

Okie69

Contributor
Sr. Member
Joined
Nov 28, 2011
Messages
842
Finally getting around to doing the D44 install. Quick question that I think I know the answer to but I just want to be sure. This axle is off of a 76-79 truck or full-size bronco correct? So going to the parts house I can have them look up things for a 78 bronco frontend for instance and should get the right stuff? Barring errors from the computer system of course.

44f3be30a06416fe3ebf728a95454b5b.jpg

a30a1b3a29c99f2d80215ded85ce6235.jpg

0efbd22c1bff8670ff64e8668e4e74cd.jpg
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Correct. Five-bolt spindles and Ford calipers indicate a '76-'79 setup, with the knuckles being the key to your happiness in the end.

The calipers, caliper brackets, spindles, hubs, rotors, seals, bearings and brake pads are all the same. The hoses will vary, but they are custom applications for swapping to EB's anyway.
Only the steering arm location and size changed between the different models:
1. '76/'77 EB - outward facing arms with small tapered holes. Least desirable to some, but still work. Need longer tie-rod and smaller ends.
2. '76-'79 Standard F150 - arms slightly lower and with larger holes, but at a normal width. Most common, work well but need to adapt tie-rod ends.
3. F150 Super Cab - highest arms of the full-size, with same large holes. Most desirable from a clearance standpoint. Still need to adapt tie-rod ends.
4. '78/'79 Bronco - not sure if they are different than the F150, but it would make sense to change the arm location due to the radically different wheelbase setups between Broncos and pickups. Never checked part numbers though.

But that's neither here nor there for buying parts. Just how they will fit and work on a Bronco.

Paul
 
OP
OP
Okie69

Okie69

Contributor
Sr. Member
Joined
Nov 28, 2011
Messages
842
Correct. Five-bolt spindles and Ford calipers indicate a '76-'79 setup, with the knuckles being the key to your happiness in the end.

The calipers, caliper brackets, spindles, hubs, rotors, seals, bearings and brake pads are all the same. The hoses will vary, but they are custom applications for swapping to EB's anyway.
Only the steering arm location and size changed between the different models:
1. '76/'77 EB - outward facing arms with small tapered holes. Least desirable to some, but still work. Need longer tie-rod and smaller ends.
2. '76-'79 Standard F150 - arms slightly lower and with larger holes, but at a normal width. Most common, work well but need to adapt tie-rod ends.
3. F150 Super Cab - highest arms of the full-size, with same large holes. Most desirable from a clearance standpoint. Still need to adapt tie-rod ends.
4. '78/'79 Bronco - not sure if they are different than the F150, but it would make sense to change the arm location due to the radically different wheelbase setups between Broncos and pickups. Never checked part numbers though.

But that's neither here nor there for buying parts. Just how they will fit and work on a Bronco.

Paul


Awesome info as always! So as far as the parts houses need to know I’ll have something like a 78 F150 4x4 when buying front axle goodies.

Or I guess I could just call the the very knowledgeable staff at Wildhorses and have them send me all the right stuff!
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Great idea!;D

We do have the hoses too, depending on what type of hose you want.
If you just want rubber, a '76 TWO-WHEEL drive hose works. If you want braided then we have those on the shelf.
Although we generally have good luck with rubber out here in this climate, even here the braided with coverings still last longer.

Essentially a braided stainless hose gives you a firmer pedal too, but it would be hard to tell the difference between a brand new rubber hose and a good stainless one. Just as they age sooner you'll be able to tell the difference.

You've been doing this stuff for a long time now, but have you done front wheel bearings before? You know the procedure for a Dana drive axle? We've run it down many times of course, but if you're not familiar we can do it again.

Paul
 
OP
OP
Okie69

Okie69

Contributor
Sr. Member
Joined
Nov 28, 2011
Messages
842
Great idea!;D

We do have the hoses too, depending on what type of hose you want.
If you just want rubber, a '76 TWO-WHEEL drive hose works. If you want braided then we have those on the shelf.
Although we generally have good luck with rubber out here in this climate, even here the braided with coverings still last longer.

Essentially a braided stainless hose gives you a firmer pedal too, but it would be hard to tell the difference between a brand new rubber hose and a good stainless one. Just as they age sooner you'll be able to tell the difference.

You've been doing this stuff for a long time now, but have you done front wheel bearings before? You know the procedure for a Dana drive axle? We've run it down many times of course, but if you're not familiar we can do it again.

Paul


Oh no no I haven’t done anything. It’s still sitting disassembled in the garage. I’m
Still debating on having it put together or
doing it myself. Leaning towards doing it myself, but the bearings and seals and all that still have me a little intimidated.

I’ve finally got an engine to put in so now it’s time to get into gear and start getting things done.
 
OP
OP
Okie69

Okie69

Contributor
Sr. Member
Joined
Nov 28, 2011
Messages
842
I should say every time I get over being intimidated by something and just do it, it ends up being much much easier than I thought it would be!
 
Top