• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

D44 Assembly

jamesroney

Contributor
Bronco Guru
Joined
Sep 11, 2007
Messages
2,607
Loc.
Fremont, CA
Yes sir. The 69 with the later model hp d44. I need all the lines from the flex line down to the axle (2.5” lift) all the way out to the calipers. Does that make it easier? 😂

I’m the installer. The only existing lines I have are the old ones off of the D30 and I’m thinking I’ll just replace them all while I’m here.
OK, we are 3 months and 7 days since I posted thread #31.

Hopefully now it makes more sense? Until you answer the fitting size question in thread #31...you are going to get ambiguous answers.

There is no right or wrong choice. You just need to pick a standard. The everything else falls into place.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Ok, not a bad idea. Especially since they may not fit. But having them as a template might be invaluable at this point!

Can you test-fit the old D30 hard lines over the top of your new 44 just to see how they fare, length-wise and bend-wise? This knowledge can only help in your choice of other parts.
If you're sourcing your pre-bent lines like it sounds, this info can be critical since some of the tight bends are VERY axle specific. In fact, sometimes they don't even fit when they're supposed to without a little tweakage from the installer!

Your full-size 44 is going to have some different orientations of critical brake line components as far as I know. James would probably have more direct knowledge for sure, but some things I'm thinking about are:
1. The location of the vent hole, which is where the main brake line junction attaches.
2. The actual length of the tubing compared to a stock Bronco 44.
3. Existing tube clamps from Ford/Dana if you're going to be using them.

If your original 30 hard lines don't line up with any of this stuff, then neither will any of ours. The new ones are based on a stock Bronco axle, so could be way off when used as expected with yours.
It might end up being necessary to bend your own brake lines. It's an extra hassle, but I find that it's actually a lot of fun too. Very rewarding...
Except when you kink one right at the last bend!!!!! Oy.

Ok, so let us know where you stand now. Crossing fingers that you or James Roney or one of the other members that have done this will know for sure which direction you need to go.
Only once you've determined what hard lines you're going to end up with will you know what soft caliper hoses you will need.

Paul
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Thanks James.
I'll have to go back and re-read #31 too.
What do you think the vent location and bends on top of the pumpkin dictate in this situation? Custom bent lines, or one of the factory setups?

Paul
 

jamesroney

Contributor
Bronco Guru
Joined
Sep 11, 2007
Messages
2,607
Loc.
Fremont, CA
Thanks James.
I'll have to go back and re-read #31 too.
What do you think the vent location and bends on top of the pumpkin dictate in this situation? Custom bent lines, or one of the factory setups?

Paul
I like the Wild H. factory bent Bronco lines. You can nudge them to fit the existing vent hole on top of the High Pinion housing. If you are running the big fittings, the (#3197 76-77 DISC) works great. If you want small fittings, the (#3197 71 1/2-75) is the answer.

I personally like using the small fittings, because the brake hoses are way cheaper. But if you use the big fittings, then everything is 100% "1976 Ford Bronco"

No right or wrong answer. It comes down to preference. Don't quote me on those part numbers. I think they are right.
 
OP
OP
Okie69

Okie69

Contributor
Sr. Member
Joined
Nov 28, 2011
Messages
842
OK, we are 3 months and 7 days since I posted thread #31.

Hopefully now it makes more sense? Until you answer the fitting size question in thread #31...you are going to get ambiguous answers.

There is no right or wrong choice. You just need to pick a standard. The everything else falls into place.


Sorry sir. I move slow I guess. I want whatever is easiest if everything else is the same. I am planning on new hoses from axle line all the way out to the calipers. Getting new calipers as well. Just want to make sure everything is gonna play nice before I start buying. I do have the original brackets for the hard line to soft line transition at the caliper that I’ll have to use. That being said being able to say everything is ‘76 bronco in the future sounds appealing.
 
OP
OP
Okie69

Okie69

Contributor
Sr. Member
Joined
Nov 28, 2011
Messages
842
I’ll take the lines off of the d30 tonight and see how they fit on the d44 and try to answer your questions Paul.
 

jamesroney

Contributor
Bronco Guru
Joined
Sep 11, 2007
Messages
2,607
Loc.
Fremont, CA
Sorry sir. I move slow I guess. I want whatever is easiest if everything else is the same. I am planning on new hoses from axle line all the way out to the calipers. Getting new calipers as well. Just want to make sure everything is gonna play nice before I start buying. I do have the original brackets for the hard line to soft line transition at the caliper that I’ll have to use. That being said being able to say everything is ‘76 bronco in the future sounds appealing.
Didn't mean to imply that you are moving slow. Sorry about that.

You claim that you have the hard line to soft line transition brackets. I want to believe that. But I'm looking at your HP44, and I don't see them. (yes, I see them on your D30, but they bolt to the bump stop bracket that is welded to the tube, and I don't see that in your housing pics.)

The bracket itself is trivial. Having a place to bolt the bracket is kind of important.

When I found myself in the situation where the D44 ended up without bump stops, and without brackets...then another option came into play. My front 44 is similar to yours. I decided to route the caliper brake hoses directly to the frame, and made up my own frame mounted brake lines. (I'll post some pics in a minute.) After I bought the front stainless hard line kit, and the prop valve, and the extended front brake hose, and the stainless flex lines...it got a lot cleaner to take all the brake line stuff off the housing. Throwing Duff Arms into the mix makes the brake line bracket even more challenging.

I hope that make sense.
 

Attachments

  • 702AEDAE-3E2D-4903-AEFB-0B4A9A8BDD8E.jpeg
    702AEDAE-3E2D-4903-AEFB-0B4A9A8BDD8E.jpeg
    118.8 KB · Views: 118
  • D6BB1D48-D9A5-42AE-9B21-ECF63E4EBD61.jpeg
    D6BB1D48-D9A5-42AE-9B21-ECF63E4EBD61.jpeg
    126.4 KB · Views: 120
  • 113212BE-1EB9-45B0-9F65-F3F57850492A.jpeg
    113212BE-1EB9-45B0-9F65-F3F57850492A.jpeg
    124.2 KB · Views: 54
OP
OP
Okie69

Okie69

Contributor
Sr. Member
Joined
Nov 28, 2011
Messages
842
Hey I understand the skepticism. There are brackets attached to the lines on the old calipers. I’ll take a picture of them when i get home in a little while. Just based on what they look like and the threaded holes on the axle I figured they were the brackets I need.
 

Seventee

Contributor
Sr. Member
Joined
Dec 7, 2012
Messages
999
Loc.
In the sticks of MT
I like the Wild H. factory bent Bronco lines. You can nudge them to fit the existing vent hole on top of the High Pinion housing. If you are running the big fittings, the (#3197 76-77 DISC) works great. If you want small fittings, the (#3197 71 1/2-75) is the answer.
Actually, on a 78-79 HP 44 the vent hole is in the casting where the driver's side tube enters the center section. There are two pics I posted in this thread that may help the OP, the first being the factory 78-79 bracket arrangement (also showing the vent hose), and the second being my solution using the extended center brake hose from the original D30:

https://classicbroncos.com/forums/threads/hp-dana-44-vent-location.299427/#post-3248796

I bolted the center brake hose junction block to the blind hole in the top of the HP center section where the factory 78-79 bracket normally bolts to, and tweaked the hard lines to fit. From there out I believe I used 76/77 Bronco lines as you do, but I don't recall how I handled the bracketry at the outer ends. I'll try to remember to take some pics and post later in attempt to help the OP out.

But I really like what you did by attaching custom lines to the frame. That's a slick way of doing it!
 
OP
OP
Okie69

Okie69

Contributor
Sr. Member
Joined
Nov 28, 2011
Messages
842
Alright guys I’ve got some pictures.

Soft line transition brackets I was talking about
AC0F2119-9B94-4991-8FAF-90F0C7EFE8B1.jpeg


I assumed these were the holes for them but I haven’t gotten around to verifying yet.
639DEA1B-0E53-4C53-AA19-3273DA515C85.jpeg
4EF8490E-AA64-42AA-9AAD-E3AC09ED4BFF.jpeg


This may be what seventee was referring too but I’ve got two holes that look like they could be for the junction block/ breather assembly.
82E18EEC-B69B-4766-8B34-68DDCE51680F.jpeg
ED22C8D4-AAFA-4122-BBC9-C831F1AD7D90.jpeg
8763128C-C9E8-49BA-9C36-BF55F4F86046.jpeg


I assume that smaller hole is where someone had an air locker installed in this housing at one point?
 

Seventee

Contributor
Sr. Member
Joined
Dec 7, 2012
Messages
999
Loc.
In the sticks of MT
Alright guys I’ve got some pictures.

Soft line transition brackets I was talking about
View attachment 879336

I assumed these were the holes for them but I haven’t gotten around to verifying yet.
View attachment 879340 View attachment 879341

This may be what seventee was referring too but I’ve got two holes that look like they could be for the junction block/ breather assembly.
View attachment 879337 View attachment 879339

I assume that smaller hole is where someone had an air locker installed in this housing at one point?
The large hole on the left is for the vent hose. The threaded hole in the top of the center section is where the original 78/79 center hose bracket bolts to. The small hole below that is for a locating tab on the 78/79 bracket. Here's a clearer picture from that thread I referenced.

917cced0-86ab-46b0-8b5c-f122beee6dc7-jpg.490954
 
Last edited:
OP
OP
Okie69

Okie69

Contributor
Sr. Member
Joined
Nov 28, 2011
Messages
842
The large hole on the left is for the vent hose. The threaded hole in the top of the center section is where the original 78/79 center hose bracket bolts to. The small hole below that is for a locating tab on the 78/79 bracket. Here's a clearer picture from that thread I referenced.

917cced0-86ab-46b0-8b5c-f122beee6dc7-jpg.490954

Oh I see I appreciate the picture.

From that picture it looks like I might end up needing to bend my own lines anyway.
 
OP
OP
Okie69

Okie69

Contributor
Sr. Member
Joined
Nov 28, 2011
Messages
842
So I ran into a slight problem. I haven’t assembled anything from the knuckles out yet. So I don’t know where the calipers are going to land and since I don’t know how the calipers are going to land I don’t know how to orient those brackets. But to me it doesn’t look like those brackets can go into the holes I thought they were going to go in.

But, the holes in the bracket are spaced perfectly for the holes in the axle so maybe they do go there.

All of this is making me think I need to start thinking about bending/flaring my own lines which is a whole new thing I haven’t thought about.

D4C59A96-C18C-4E24-A683-D981EDF6D7E9.jpeg
 

jamesroney

Contributor
Bronco Guru
Joined
Sep 11, 2007
Messages
2,607
Loc.
Fremont, CA
Oh I see I appreciate the picture.

From that picture it looks like I might end up needing to bend my own lines anyway.
You can mount the early bronco frame-to-axle brake hose using the same hole that was used to install the 78-79 brake hose bracket. (I called it the vent hole, but it is actually not the vent hole. I'll try to be more accurate in the future.) In my D44 HP, I threaded it to 7/16x20 and used the dana 30 vent bolt in that location. If you mock that up...you will see that the dana 30 brake tubes are pretty close.

But you are going to have issues on the outboard side. Don't forget to temporarily hang your T-Rex arm on the housing. you will see that the location used by the Dana 30 brackets is not compatible.

Those other brackets are home-brew. I hope they work for you.
 
OP
OP
Okie69

Okie69

Contributor
Sr. Member
Joined
Nov 28, 2011
Messages
842
Do all of the HP D44 with discs from these years say 76-77 bronco and 77-79 f-series and 78-79 big bronco use the same calipers and rotors? Just wondering.

I’m leaning towards trying to massage some 76-77 lines into fitting this housing.
 

Seventee

Contributor
Sr. Member
Joined
Dec 7, 2012
Messages
999
Loc.
In the sticks of MT
So I ran into a slight problem. I haven’t assembled anything from the knuckles out yet. So I don’t know where the calipers are going to land and since I don’t know how the calipers are going to land I don’t know how to orient those brackets. But to me it doesn’t look like those brackets can go into the holes I thought they were going to go in.

But, the holes in the bracket are spaced perfectly for the holes in the axle so maybe they do go there.

All of this is making me think I need to start thinking about bending/flaring my own lines which is a whole new thing I haven’t thought about.
Those brackets do in fact mount using those holes. Orient them pointing up with the rubber hoses pointed out and it will make more sense.

You'll be doing some custom bending regardless which lines you go with, there is no perfect solution. The 76/77 lines get you close though.
 

jamesroney

Contributor
Bronco Guru
Joined
Sep 11, 2007
Messages
2,607
Loc.
Fremont, CA
Do all of the HP D44 with discs from these years say 76-77 bronco and 77-79 f-series and 78-79 big bronco use the same calipers and rotors? Just wondering.

I’m leaning towards trying to massage some 76-77 lines into fitting this housing.
yes. Calipers are Raybestos 4095, and 4096 from 75-79 F-series, and 75-83 E-series.
(HOSES are different. 76-77 Bronco use oversized 7/16x20 flare nuts.)

And based on the pics in the FSB.com link, the 76-77 F100 4x4 hoses are different than 78-79.

I think that your prediction in post #20 is going to end up 100% correct.
 
Last edited:

Seventee

Contributor
Sr. Member
Joined
Dec 7, 2012
Messages
999
Loc.
In the sticks of MT
Sorry I should have clarified in my posts, I used 76/77 Bronco lines, not F100. I'm certain I used the outer brackets for the 78/79 hoses as I recently had to remove the passenger side to access the track bar bolt. I should have time to take some pictures tonight.
 
Top