• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Dana 44 guru

408Bronco

Sr. Member
Joined
Sep 12, 2011
Messages
381
Loc.
Midwest
Im trying to finish up the installation of my narrowed high pinion out of a 79 Bronco going in my 75. I added Reid knuckles, the passenger side was shortened 6 inches, i'm running 76 Bronco dana 44 spindles and caliper brackets. While finishing up the driver side install, I was putting the snap ring on and it wont seat in the groove on the axle shaft, it looks as if the axle needs to be pulled out about 1/16 of an inch, or the spindle needs to shortned 1/16 of an inch, i'm adding picks, but they are pretty crappy. Any ideas on what to do to slove this problem. The axle moves freely when turning the pinion yoke. Thanks.
 

Attachments

  • IMG_0896.jpg
    IMG_0896.jpg
    84 KB · Views: 84
  • IMG_0899.jpg
    IMG_0899.jpg
    54.3 KB · Views: 65

Amac70

ME
Joined
Mar 27, 2002
Messages
3,269
have you tried pushing the axle out from the knuckle there is usually a bit of play in there.
otherwise i wouldnt worry about it lots of people run with out the snap ring in the end of the axle.
 

TwoDalesDad

Bronco Guru
Joined
Jul 19, 2011
Messages
1,515
Rotate the axle a few times then again pull out as needed..some axles can become stuborn...
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
It's a very common issue more for the use of aftermarket hubs, than any of the other mods you've made.
Unless of course you're using outer axle shafts from some other application, or there is something limiting the outward movement of the shaft.
Look into that first, but it's probably the locking hub mechanism keeping it from reaching the groove.

As mentioned, you can live without it.

Paul
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
And since it looks like you have the type of axle shafts with the threaded holes in the ends, you can substitute a fender washer and short bolt as a retainer if you feel you need something there.

Pau
 

broncosbybart

Bronco Guru
Joined
Mar 13, 2002
Messages
2,644
I'm running stock hubs on my EB. I have a set of Yukon stubs that won't accept the snap ring. If I force them out really hard, they will go, but then it wants to eat up that plastic thrust washer between the stub and the back side of the spindle. Haven't had this issue running some other aftermarket shafts. Just go without the snap ring.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
broncosbybart pointed out something important here. Even if you can get the ring or other retention method installed, you don't want to do it at the expense of movement.
There has to be some freeplay in the axle so that it can move in and out slightly when things move around. And also not be in constant contact with the washers and stuff when it's spinning.

If you can't retain it while maintaining some amount of looseness, then either machine your own groove or just leave it be and run without a clip or washer

Paul
 
OP
OP
408Bronco

408Bronco

Sr. Member
Joined
Sep 12, 2011
Messages
381
Loc.
Midwest
Thanks for the great responces, I was guessing that the clip was there just to hold the stub shaft in case you blow up a U joint or something of that nature, i'll have to take another look at it.
 

Ranchtruck

Sr. Member
Joined
Feb 7, 2008
Messages
768
The clip is there to keep the axle moving in to the diff. That keeps the centerline of the U-joint lined up with the centerline of the ball joints and it keeps the axle against the seals on the back of the spindle so water can't get into the hub.
 
Top