• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

EFI issues after storage

SevenT

Contributor
Sr. Member
Joined
May 23, 2009
Messages
523
Loc.
Southern Colorado
My engine has sat for three years while I did the the Bronco Design tub and build up from there.

My Bronco runs. However, it will not idle evenly cold and is running really rich. It smells like it did with the old Holley carb. This is a stick with a stick computer. It ran and drove fine with the auto until 2017.

Is my fuel pressure regulator failing? Or do I have an injector stuck open?

v/r,

SevenT
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,112
With any computer the first thing I do is pull codes. It will tell you so much more than guessing.

Lots of possible issues, even the caps in the computer failing could cause it.
 

nvrstuk

Contributor
Just a Bronco driver for over 50 yrs!
Joined
Jul 31, 2001
Messages
10,622
Loc.
PNW
What Broncobowsher said but also. is it 3 yr old gas??
 

trailpsycho

Bronco Guru
Joined
Dec 11, 2003
Messages
4,856
I am rectifying this very thing now. Mine sat for 3 yrs while I was focused on other things with a bad FMS harness and failing Mustang ECM. I upgraded to the OBD-II setup and it ran great, but quickly fouled up and almost left me stranded. Bad gas, decaying (14-15 yr old braided SS lines)....there was gray sediment from the decaying fuel lines circulating in the system.

I dropped the tank, cleaned it and decided to go with the in-tank pump, new updated braided SS lines, a new FP reg...and, of course, adding all of the other emissions stuff that I never had to install when I lived in IN or AL.

About 3/4 through the new true dual, 4 cats, Borla muffs and resonators install. Hopefully, it will be worth the effort, work and expense.

My system was getting no FP to the rail, so I probably needed to replace one or both of the pumps anyway. It was time to upgrade a bunch of stuff from the original build, so, for me, it is what it is.

I hope your fix is just a filter change or FP regulator sticking. Good luck!

John
 

Jdgephar

Bronco Guru
Joined
Sep 25, 2012
Messages
1,526
Could be an injector stuck open, however, you will know when that happens by looking at the exhaust. When the fuel combines with the water vapor, you get a milky white fluid out the exhaust pipe, and lots of liquid fuel if there are leaks further upstream (I had a stuck injector briefly).

Just out of curiously, when you went from an auto trans to the manual, did you change anything with the harness and computer (you should not have, as the harness needs to match the computer).

As said, pull the codes. That may help. You can measure fuel pressure with a gauge connected to the Schroeder valve on the fuel rail.
 
OP
OP
SevenT

SevenT

Contributor
Sr. Member
Joined
May 23, 2009
Messages
523
Loc.
Southern Colorado
EFI issues

All,

No codes. The harness (RJM) is set for a manual. The gas was about two years old. I got a new FPR and injectors. I plan on draining the tank, replacing the parts and starting over with the idle adjustment. Hope to do this over the weekend. More to follow.

v/r,

SevenT
 
OP
OP
SevenT

SevenT

Contributor
Sr. Member
Joined
May 23, 2009
Messages
523
Loc.
Southern Colorado
All,

Drained the tank, changed the injectors (19 lb correct ones) and FPR. Took that stupid phenolic spacer out that i used to clear the brake lines. Clearanced the intake to clear the brake lines. Back to same configuration that was in the truck and running before. It still will not idle and runs kinda rich. I need to try to reset the computer by disconnecting both cables for 30 plus minutes. Will start from there. Gotta get this solved. Super Celebration West is next week.

Any thoughts are appreciated. Could my TPS, MAP sensor or O2s be bad?

It does not throw any codes other than the soft ones. Codes 33, 81, 82, 84, 85, 44 & 94 are normal when the smog solenoids CANP, EGR, TAB & TAD are deleted.

v/r,

SevenT
 

onpier55

Sr. Member
Joined
Oct 19, 2017
Messages
354
Loc.
Roseville Ca
I’m not familiar with the mustang stuff. But I have an explorer motor. I was having an issue and had to clean and then replace my idle air control valve.good luck.
 
OP
OP
SevenT

SevenT

Contributor
Sr. Member
Joined
May 23, 2009
Messages
523
Loc.
Southern Colorado
ALL,

Problem solved. After driving to Super Celebration West in a truck that guzzled gas worse than a badly tuned carb, we were introduced to "The EFI Guy". He checked the fuel pressure, it was good. Had him look at the computer and found out I got a Speed Density one and not Mass Air. Hooked a vacuum line to BAP and made it a MAP and she idles and sips fuel, no longer guzzling. Will order correct ECM upon return home. Still can't trust parts stores to get the right parts. I can't sing the praises of "The EFI Guy" enough. Thanks for everyone's help on this journey.

Mike "SevenT" Norton
 

toddz69

Sponsor/Vendor
Bronco Guru
Joined
Nov 28, 2001
Messages
11,222
Mike:

It was great to meet you at SC West - glad to hear your problems were solved! I finally met Garry in person too and got a hat! I had to explain what it all meant to my family when I got home last night :).

Todd Z.
 
OP
OP
SevenT

SevenT

Contributor
Sr. Member
Joined
May 23, 2009
Messages
523
Loc.
Southern Colorado
Todd,

It was awesome to meet you as well. I love the book, have barely scratched the surface of it. Garry is the best. Now the problem is finding a 91 Mass Air ECM. Looks like everyone is out of stock. I have my fingers crossed on getting one. I can continue to drive it the way it is now, but that is not optimal.

v/r,

MIke "SevenT" Norton
 
Top