Explorer Serpentine Conversion - PS pulley

[GrillMaster]

Have the explorer serp conversion with the Wild Horses bracket and Sag pump. Anyone have a part number on a pulley that will work on the Saginaw PS pump?

 

[toddz69]

I used GM PN 14100597NU.

Todd Z.

 

[GrillMaster]

Thank you but I cant seem to find it from any of the parts dealers

 

[toddz69]

Thank you but I cant seem to find it from any of the parts dealers

I did a quick search online and found a couple on Ebay.

Here's a pretty one:

https://www.ebay.com/itm/1753441967...d=link&campid=5335857059&toolid=20001&mkevt=1

Here's one you can clean and paint yourself:

https://www.ebay.com/itm/1753441967...d=link&campid=5335857059&toolid=20001&mkevt=1

I snagged one at a junkyard a year or two when I needed mine.

Todd Z.

 

[Madgyver]

Grillmaster, you fitting this explorer serpertine set on your Cleveland?

 

[GrillMaster]

Hi Mad!

No, I am pulling the Cleveland out and dropping a 408W in.

Going with the Doorman 300-137 pulley. Smaller size suposed to help at low RPM. Found on Amazon, $20 shipped.

 

[Josh40601]

I did a quick search online and found a couple on Ebay.

Here's a pretty one:

https://www.ebay.com/itm/1753441967...d=link&campid=5335857059&toolid=20001&mkevt=1

Here's one you can clean and paint yourself:

https://www.ebay.com/itm/1753441967...d=link&campid=5335857059&toolid=20001&mkevt=1

I snagged one at a junkyard a year or two when I needed mine.

Todd Z.

Hey Todd, or anyone else who may know. Any idea if this pulley will fit? Seems to be same width and diameter just the position from the front of the pulley to the start of the ribbed section looks different

 

[thegreatjustino]

Hey Todd, or anyone else who may know. Any idea if this pulley will fit? Seems to be same width and diameter just the position from the front of the pulley to the start of the ribbed section looks different

No link to any pulley provided.

 

[Josh40601]

No link to any pulley provided.

Well crap. It was there. Sorry about that

https://www.oreillyauto.com/detail/...rman-oe-solutions-p-s-pump-pulley/doe0/300002

 

[toddz69]

That’s not one you’d use for the Explorer conversion.

Todd Z.

 

[Josh40601]

That’s not one you’d use for the Explorer conversion.

Todd Z.

Thanks Todd

 

[Tiko433]

Did you find a smaller pulley ? I was looking for on also . A little smaller then the stock one I have

 

[ntsqd]

I used GM PN 14100597NU.

Todd Z.

The "NU" suffix isn't part of a normal GM p/n. Am guessing TZ's vendor added them for their own reasons. Try searching just the string of numbers w/o the "NU"

 

[snipes243]

You might Try Howe Steering they have some smaller diameter pullies.

https://www.howeperformance.com/parts/p-or-n-pump-pulleys/

 

[1969miller]

This will work if your pump has a 3/4" OD Shaft.

https://www.wildhorses4x4.com/power-steering-pump-serpentine-pulley

 

[toddz69]

The "NU" suffix isn't part of a normal GM p/n. Am guessing TZ's vendor added them for their own reasons. Try searching just the string of numbers w/o the "NU"

I found the one I used online in this ebay listing:

https://www.ebay.com/p/22010764303

Has that "NU" suffix on it too but I certainly didn't pay that much for it! Grabbed it from a Firebird or Camaro in the junkyard.

Todd Z.

 

[toddz69]

Well crap. It was there. Sorry about that

https://www.oreillyauto.com/detail/...rman-oe-solutions-p-s-pump-pulley/doe0/300002

I should clarify on this one a bit because I thought I was reading another thread when I responded initially . I think the diameter is probably ok with that one but the offset of the pulley to the mounting hole surface is off.

Here's some visuals of the one I used:

https://www.ebay.com/p/22010764303

See how the edge of the center hole is more proud of the pulley?

IF the 5 3/4" diameter works for you, I'd probably sell you mine since I'm not going to use it in the foreseeable future.

Todd Z.

 

[ntsqd]

I found the one I used online in this ebay listing:

https://www.ebay.com/p/22010764303

Has that "NU" suffix on it too but I certainly didn't pay that much for it! Grabbed it from a Firebird or Camaro in the junkyard.

Todd Z.

That's pretty curious. I can't recall ever seeing letter suffixes on GM p/n's. I wonder what it means?

 

[WILDHORSES]

Just updated this item. It's what we use on our motors with the Explorer conversion.
https://www.wildhorses4x4.com/power-steering-pump-serpentine-pulley
Also new updated crank pulley for EX conversions
https://www.wildhorses4x4.com/custom-crank-pulley-bronco-302-explorer-5-front

Jim

 

[bigmuddy]

Just updated this item. It's what we use on our motors with the Explorer conversion.
https://www.wildhorses4x4.com/power-steering-pump-serpentine-pulley
Also new updated crank pulley for EX conversions
https://www.wildhorses4x4.com/custom-crank-pulley-bronco-302-explorer-5-front

Jim

I wish you guys would bring back the bracket for the sag/serpentine system for use with a 351w/5.8