• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Extracting sheared mirror bolt?

gnpenning

Contributor
Bronco Slave
Joined
Dec 26, 2011
Messages
2,601
Loc.
I have more questions than answers.
Here is a video of a rivnut and how they can be installed with out the tool. I only watched far enough to see if they gave a decent view of a nut. When you see what they are you will realize how easy you can drill out the old one and replace it. There is plenty more information available if that video doesn't work for you. The broken bolt shouldn't be too much of a issue doing it this way. Your drill bit should be very close to the size of the replacement rivnut.

Not knowing the location of your mirror bolt I can't really give you any help on the inside. Other than the window regulator and track I don't know what would be inside the door that could be in your way. Most likely a little contortion would be needed.

Do what you feel comfortable doing.


 

Bronco-Brian

Full Member
Joined
Jun 30, 2015
Messages
306
Loc.
Lake Oswego, OR
If you're OK with using a nut and screw instead of the rivnut, I recommend nylon locking nut and hold from the inside when tightening the screw. I've had to do this when the hole for the rivnut got jacked up from prior issues. Choose stainless steel hardware. This fix works great, just requires access from inside when tightening. But since you're already there I say go for it and skip the rivnut. There's nothing more frustrating when a rivnut isn't locking in place, and your can neither tighten or loosen a spinning nut.
 

FordBronc

Contributor
Bronco's, yea I have a couple.
Joined
Dec 26, 2010
Messages
1,518
Loc.
Polk County, Missouri
The current riv-nut (also called a nut-sert) is crimped/flared/compressed (by the insertion tool) to stay/lock in the surrounding sheet metal and not turn. So go ahead and try to drill and remove the broken bolt best ya can. As soon as you break the nut-sert loose from the surrounding sheet metal, you might as well plan on removing it all together and replace.

Probably have to upsize it a bit (if you want to use a nut-sert again, since when it breaks loose from the surrounding sheet metal it will NOT relock or retighten and just spin and spin. Or just go with the stainless hdwr and a nylon lock nut and hold and tighten from the backside. IF you can get on it from inside the door.
 

jamesroney

Contributor
Bronco Guru
Joined
Sep 11, 2007
Messages
2,612
Loc.
Fremont, CA
You assessed it correctly. The surface is not flat, and my attempts to drill into it resulted in the bit wandering too close to the threads, which would cause an even bigger problem. I ordered a Wybenz screw extractor and left hand drill bit set from Amazon. Maybe I can get a better result with that. In the meantime, I’m going to study up on your centering technique as described, and get comfortable with that and have another go at it when the extractor set arrives later this

You left out a critical detail. Why did the 10-24 machine screw break off? Did it break off because something hit the mirror and broke the head off, or did it break off because someone was trying to unscrew it? (or tighten it?) It's critical because it will tell you whether the nutsert is fused to the threads, or if the threads are basically intact.

In either case, I wouldn't spend more than about 3 minutes drilling it. You've already invested WAY more time and effort than I would have done.

Step 1. take masking tape and tape around the nutsert, protecting any decent paint.
Step 2. Take a small die grinder, with about a 1/16 x 2 inch cut off wheel, and grind off the head of the nutsert. Grind it slow and carefully, and you won't even burn the paint.
Step 3. Drive the dead nutsert with the broken off screw into the door.
Step 4. Install a new nutsert.
Step 5. Install a new screw.
 
OP
OP
MKMcCoy

MKMcCoy

Veteran Young Guy
Joined
Oct 21, 2021
Messages
59
Loc.
30A, Inlet Beach, FL
Addenda:

I have given up on the bolt extraction, main issue now is during all the on/off with the interior door hardware, I have now managed to mess up the angle of the interior door paddle lever to the rod inside the door that opens the door. I am now 0/32 in trying to get it back right - it 'slips' off the rod every time. I've shaved some of the padding on the door card, tried to adjust the angle of the rod closer to the paddle lever, etc...

So, current plan: If you've seen my other posts on the idle/transmission/tailgate bolt/etc..., all of these fixes will nom one addressed by the local custom shop, namely

-Cold idle too high
-Trans violent shifts when cold
-Warm idle too low when shifting P-N-R, or D-N-R (dies when parking or maneuvering when warm)
-Retrieve bolt dropped in tailgate
-Extract bolt and re-mount PS mirror
-Install the Duff's door checks I bought
-How much to source/install 'new' multi gauge?
-How much to source/install shoulder belts in front?

None of the above have dampened my enthusiasm - I LOVE it.

Stay tuned.
 
OP
OP
MKMcCoy

MKMcCoy

Veteran Young Guy
Joined
Oct 21, 2021
Messages
59
Loc.
30A, Inlet Beach, FL
You left out a critical detail. Why did the 10-24 machine screw break off? Did it break off because something hit the mirror and broke the head off, or did it break off because someone was trying to unscrew it? (or tighten it?) It's critical because it will tell you whether the nutsert is fused to the threads, or if the threads are basically intact.

In either case, I wouldn't spend more than about 3 minutes drilling it. You've already invested WAY more time and effort than I would have done.

Step 1. take masking tape and tape around the nutsert, protecting any decent paint.
Step 2. Take a small die grinder, with about a 1/16 x 2 inch cut off wheel, and grind off the head of the nutsert. Grind it slow and carefully, and you won't even burn the paint.
Step 3. Drive the dead nutsert with the broken off screw into the door.
Step 4. Install a new nutsert.
Step 5. Install a new screw.
Reading my mind...if the quote to fix from the local shop is too much, this is what I'll do, looks like those 'outserts are easily sourced. Thank you.
 
OP
OP
MKMcCoy

MKMcCoy

Veteran Young Guy
Joined
Oct 21, 2021
Messages
59
Loc.
30A, Inlet Beach, FL
You left out a critical detail. Why did the 10-24 machine screw break off? Did it break off because something hit the mirror and broke the head off, or did it break off because someone was trying to unscrew it? (or tighten it?) It's critical because it will tell you whether the nutsert is fused to the threads, or if the threads are basically intact.

In either case, I wouldn't spend more than about 3 minutes drilling it. You've already invested WAY more time and effort than I would have done.

Step 1. take masking tape and tape around the nutsert, protecting any decent paint.
Step 2. Take a small die grinder, with about a 1/16 x 2 inch cut off wheel, and grind off the head of the nutsert. Grind it slow and carefully, and you won't even burn the paint.
Step 3. Drive the dead nutsert with the broken off screw into the door.
Step 4. Install a new nutsert.
Step 5. Install a new screw.
It broke when I bumped the mirror after I had loosened each bolt a bit too tighten them back up. I was trying to minimize the 'shake' when driving.
 

tirewater

Bronco Guru
Joined
Jan 28, 2011
Messages
1,046
Loc.
San Francisco Bay Area
Providing the screw doesn't have thread lock on it, it shouldn't be too hard to screw in or out.

1. Try grabbing the little bit of thread that's sticking up with a vicegrips and slowly unscrew.
or
2. Use a small dremel grinder bit, grind a slot into the screw and use a flat bladed screwdriver to either screw in or out.

Whatever you do, be sure to tape up, or use cardboard to protect the paint in case you slip.

If you have a shop fix the bolt, odds are they'll scratch the paint - unless you request that they protect the paint, or they have the ultra experienced bolt whisperer extract it versus the kid they hired yesterday. :)
 
Top