• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Ford EFI and non-roller 302

mcknight77

Full Member
Joined
Feb 19, 2012
Messages
219
Loc.
Caldwell, ID
How feasible/doable is it to convert a non-roller carbureted 302 to EFI using Mustang 5.0 EFI?

I have a conversion kit and computer that I was going to use to convert my 1988 Mustang 5.0 to Mass-air. I'm thinking that with the addition of intake, flow meter, distributor, etc. that it should work fine on my 302. Am I missing something here?
 

bmc69

Contributor
Bronco Guru
Joined
Jun 11, 2004
Messages
12,015
It's done often. No issues. Sounds like you have the list of what you need pretty much figured out.
 

dclack

Sr. Member
Joined
Feb 16, 2012
Messages
402
The biggest issue in the engine firing order vs the injector firing order.
 

Scoop

Contributor
Bronco Old Fart
Joined
Feb 1, 2006
Messages
11,121
Loc.
Cuchara, CO
The biggest issue in the engine firing order vs the injector firing order.

If the 302 is basically stock just run a speed density set up and the firing order will match. You only need MAF if you build the motor out of the SD computer range. SD works great and is cheaper to buy the parts. I'm running an 87 Cougar XR7 SD set up on a stock 74 motor with the stock v-belt set up. Works very well.
 

Ourobos

Bronco Guru
Joined
Jan 7, 2008
Messages
1,225
Loc.
Big Island Hawaii
Sequential vs. batch firing (SD vs. Mass Air) might seem to run OK.. But the O2s are adding / pulling fuel from the wrong banks if you mix and match. Batch-EFI setups are usually the single HEGO type....one O2 reading both banks at the "Y" exhaust junction. Mass air was designed with two banks, and two O2 sensors on the Mustangs. I'd advise against it if you want the truck to run the way it's engineered to, and most efficiently. But it'll run 'OK'.

http://oldfuelinjection.com/?p=92
 

Scoop

Contributor
Bronco Old Fart
Joined
Feb 1, 2006
Messages
11,121
Loc.
Cuchara, CO
My SD set up is not batch fire. It has O2 sensors on both banks. My understanding is that batch fire systems came mainly on the F series and FSBs prior to 96.
 

Viperwolf1

Contributor
electron whisperer
Joined
Aug 23, 2007
Messages
24,451
Sequential vs. batch firing (SD vs. Mass Air) might seem to run OK.. But the O2s are adding / pulling fuel from the wrong banks if you mix and match. Batch-EFI setups are usually the single HEGO type....one O2 reading both banks at the "Y" exhaust junction. Mass air was designed with two banks, and two O2 sensors on the Mustangs. I'd advise against it if you want the truck to run the way it's engineered to, and most efficiently. But it'll run 'OK'.

http://oldfuelinjection.com/?p=92

All speed density systems are not batch-fire. The '85-'88 mustangs were sequential speed density. No problem changing it to mass air. Ford even had a conversion kit for it. Either way it should run perfectly fine.
 

Sporto

Sr. Member
Joined
Oct 10, 2005
Messages
923
I agree with Scoop. The SD setup is the way to go on stock or slightly modified 302 engines. I have setup from an 86 Mustang HO on mine with an Edelbrock Performer cam. I ran this engine as is with the Edelbrock carb and manifold for years, and when I put the EFI on it made a huge difference in the engine's performance and reliability. I know that the firing order that the computer is setup for is the HO one, and it is different than mine, but if this engine is just running "ok" then I would hate to see what running "good" would be. :eek:
 

Ourobos

Bronco Guru
Joined
Jan 7, 2008
Messages
1,225
Loc.
Big Island Hawaii
You'd be amazed at what a properly running engine would reveal. I've had them running 'great', and via a tune gained over 30hp. It's normally the idle that's effected with the injectors not matching the firing order. Whatever floats your boat though.
 
OP
OP
M

mcknight77

Full Member
Joined
Feb 19, 2012
Messages
219
Loc.
Caldwell, ID
My 302 is basically stock, 8.5 compression, small cam, E-brock Performer and 500 cfm E-brock carb. Dyno'ed at 230 hp and 290 tq. Just looking for drivability. Sounds like the SD is the way to go, but I already have the computer an wiring for MA.

One last question: fuel pump?

Thanks for the help.
 

Viperwolf1

Contributor
electron whisperer
Joined
Aug 23, 2007
Messages
24,451
My 302 is basically stock, 8.5 compression, small cam, E-brock Performer and 500 cfm E-brock carb. Dyno'ed at 230 hp and 290 tq. Just looking for drivability. Sounds like the SD is the way to go, but I already have the computer an wiring for MA.

One last question: fuel pump?

Thanks for the help.

Mass air is fine as is speed density. Use what you have.

You'll need a high pressure fuel pump at a minimum. Mount it as close to the tank as you can and it'll be fine. You'll also need a return line between the fuel rails and the tank.
 
OP
OP
M

mcknight77

Full Member
Joined
Feb 19, 2012
Messages
219
Loc.
Caldwell, ID
EFI Photo

Here's a photo of what I bought.
 

Attachments

  • EFI1.jpg
    EFI1.jpg
    107 KB · Views: 109

jw0747

Bronco Guru
Joined
Nov 22, 2006
Messages
2,434
Loc.
San Antonio, TX
Looks like you'll need an EEC module (computer) and a wiring harness plus some sensors unless you didn't picture everything you got.
 
OP
OP
M

mcknight77

Full Member
Joined
Feb 19, 2012
Messages
219
Loc.
Caldwell, ID
I already have the computer. It's a A9L.

I'll have to source the sensors. And an EFI distributor.

I'm checking on a harness. I have a Mass Air conversion harness, but I'm leaning toward an aftermarket harness specifically for 5.0 into an early Bronco.
 

Viperwolf1

Contributor
electron whisperer
Joined
Aug 23, 2007
Messages
24,451
Looks like a Mustang lower intake. Upper appears to be off something else. Might have a small sized throttle body. It should work though.
 

Scoop

Contributor
Bronco Old Fart
Joined
Feb 1, 2006
Messages
11,121
Loc.
Cuchara, CO
Also don't see the mass air flow meter and you'll need O2 sensors and bungs to install them. But you want to get new O2 sensors anyway! Looks like a couple of sensors are still attached to the lower along with all the injectors and the fuel rail. Good score!
 
Top