• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Freeze Plugs

vanolefan

New Member
Joined
Apr 1, 2012
Messages
46
Loc.
Tallahassee, FL
Sometimes I hate this Bronco! I will admit I am not a master mechanic, actually really not a great mechanic at all. After addressing a number of issues this weekend, I was finally ready for a test drive around the neighborhood. She was warming up in the drive way when she blew another freeze plug. Worst of all it was the one directly behind the motor mount on the drivers side. I was able to extract the old rusted out freeze plug with a lot of effort, but putting a new one in will not be so easy.

I removed the bolts to the motor mount and I am thinking about jacking the engine up to remove the motor mount to get better access to install a new plug. Where do I jack up the motor? I tried under the harmonic balancer, but it didn't seem to raise the drivers side. Can I jack up the engine by the oil pan?

Alternatively, I have considered a rubber expandable plug. I have heard some use them with success and others say they don't hold up. Any thoughts?
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,111
Another freeze plug? So you lost more than one. They are ALL bad. That is a hint.

The rubber plugs I consider a good short term fix. Gets you running again, but not the life of an engine plug that metal is.

Instead of fighting bad angles and hard to reach plugs, have you considered just pulling the engine, repair, put back in?
 
OP
OP
V

vanolefan

New Member
Joined
Apr 1, 2012
Messages
46
Loc.
Tallahassee, FL
Broncobowsher,

Yes, this wasn't the first one. I have replaced 3 of them already and each of them were a bear to get out and in. I thought about pulling the motor, but it is a bit intimidating given I have never done it before. Maybe I will research the forum and see if there is a step by step guide for noobies on how to do it.
 

Bferrari

Sr. Member
Joined
Mar 6, 2013
Messages
857
If it was mine i would pull the motor and replace all of the freeze plugs. Once the first one goes it is just a matter of time before the rest will go. The first thing i suggest is to get brass freeze plugs, not steel. These should last longer. Then you can buy, borrow or rent a cherry picker or hoist for lifting the motor. The motor doesn't need to come all the way out, just high enough to change out the freeze plugs. You may be able to lift the motor up enough to pull off the motor mounts and not disconnect anything else to access all of the plugs. Once you have access, use a hammer and a drift pin, screw driver, etc to tap one edge of the old plug to get it to rotate in its hole. This will raise the opposite edge of the plug which will give you enough to grab on to with a set of pliers and remove. Pick up a bearing race and seal driver like this http://t.harborfreight.com/automoti...e-bearing-race-and-seal-driver-set-95853.html. This will simplify driving in a new plug. Good luck!
 

Rustytruck

Bronco Guru
Joined
Feb 24, 2002
Messages
10,872
You might as well pull the motor out. You have freeze plugs in the front and back of the heads too. Plus with the motor out you will be able to attack the inside of the block and heads and get a good flushing in there while the freeze plugs are out. Its not hard to pull the motor in a Bronco the hood flops back to the windshield giving great access. Make sure you tie it back there or a breeze will really clean you clock. The radiator support is very high and some lifts don't lift enough so plan on that. When ready to actually pull consider letting the air out of the tires to drop the front if you need too. Yank the radiator shroud and fan before you pull the motor. Invite some friends have a BBQ and engine pulling party and you could probably get this done in a day, 2 at the most. Much easier to pull with a couple of guys wrestling this stuff around. Me it would take a month because of, (While your at it you might as well) do this too. Projects like this start out as good intentions and turn into a snow ball fight and then into a full on avalanche of stuff to do. Like while its out clean up the frame and engine compartment and repaint them. Then might as reseal the motor, since the pan is now off slap in a new oil pump and rod and main bearings. Man what about the timing chain and water pump. Hey the motors out new clutch, throw out bearing and resurface flywheel before you Know it you've spent a grand on a 100 dollar project and a month has gone by. This where your BBQ party keeps you on track and saves you money, your friends wont let you snowball this into something else and delay the feast and beer.
 

ScanmanSteven

Bronco Guru
Joined
Dec 19, 2010
Messages
1,129
You can jack the motor up by the oil pan but have to exercise caution. If you have a floor jack, put a 2x6 board on the jack base then carefully jack it up. There's lot to watch doing this, like making sure you don't jack up enough to crush the pan. Make sure both motor mounts are loose, then slowly jack it up. Watch to see if the exhaust has enough travel, transmission lines, if auto, clutch linkage, shifter rods, fuel lines, ect don't hold you up. Get the idea that a cherry picker might be easier? Godd luck.
 
Top