• Just a reminder that you won't be able to start new posts or reply to existings posts in the Archive forum.

    This is where all the old posts go so they can still be used for reference and searched.
  • Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Front 7100 res. shock valving ??

ctowery

Bronco Guru
Joined
Jan 8, 2002
Messages
1,024
Loc.
Wellington Nevada
I have 255/100 now and thats what Bilstein race dept recomended. Front shocks get real hot on the Rubicon, rear 9100 res. are cool? Do ya think its the valving or the Very soft BC's 351 winch coils? I am planing to install rock-arms if I can get them to fit... maybe they will help.

Cary
 

asabadin

Sr. Member
Joined
Jun 4, 2004
Messages
360
Loc.
L.A.CALI NO THIEVES
I just did this. i talked to several people on this board After alot of research and real life advice from fellow bronco owners with 7100 shocks i went with this setup.
360/80 in front. in back i went with 275/78. all 12 inch short body reserviored shocks, it rides great.
 

68ford

Bronco Guru
Joined
Dec 26, 2004
Messages
2,710
ctowery said:
I have 255/100 now and thats what Bilstein race dept recomended. Front shocks get real hot on the Rubicon, rear 9100 res. are cool? Do ya think its the valving or the Very soft BC's 351 winch coils? I am planing to install rock-arms if I can get them to fit... maybe they will help.

Cary

if your crawlin and they are gettin hot, i would be willing to bet its your engine heatin them up. especially if the rears are staying cool, it takes high speed and alot of fast up and down to get them hot. i did some twisty stuff kinda fast couple month ago at a CORVA run and i notice it wasnt even enough to make my rear bypass tubes click open, so they really were not working hard at all. i think its your headers or manifolds.
 

Jeepincj7

Sr. Member
Joined
Jun 12, 2003
Messages
856
Loc.
Lake Elsinore, CA
ctowery said:
Engine heat...I never though of that, I will check it out.

Thanks, Cary

That valving seems way light for a coil spring rig with a 351. I used to run 255/75 7100s up front and had to pull them to revalve them. 360/80 is the correct valving for a Bronco on the front.
 

shifter

Full Member
Joined
May 2, 2004
Messages
181
Loc.
Agua Dulce, CA
I have 3 1/2 duff coils with single 7100s in the front and the 360/80 valving is a great match for those springs with the driving I do. Don't worry about the heat, you may be picking up a little from the engine but that heavy valving makes alot of heat. Unless you feel the damping fading it's not a big deal. Wish I could find something for the rear that works as good as the front, been trying to make the duff stage 2 mounts work but don't think the geometry is correct.
 

asabadin

Sr. Member
Joined
Jun 4, 2004
Messages
360
Loc.
L.A.CALI NO THIEVES
shifter said:
I have 3 1/2 duff coils with single 7100s in the front and the 360/80 valving is a great match for those springs with the driving I do. Don't worry about the heat, you may be picking up a little from the engine but that heavy valving makes alot of heat. Unless you feel the damping fading it's not a big deal. Wish I could find something for the rear that works as good as the front, been trying to make the duff stage 2 mounts work but don't think the geometry is correct.
Check out my post from my install.http://www.classicbroncos.com/forums/showthread.php?t=62331

LARS AND TODD Z DESIGNED A REAR OUTBOARD MOUNT THAT GIVES YOU THE SAME ARTICULATION OF INBOARD WITHOUT THE BODY ROLL FOR STREET DRIVING. WORKS VERY GOOD VERY EASY INSTALL AND THEY FURNISH YOU WITH THE CORRECT GEOMETRY. 60.00 WELL SPENT. ALSO THE CONSENSOUS ON THIS BOARD AS WELL AS LEE FROM RACESHOCK.COM TO MATCH THESE MOUNTS IS 275/78 12 INCH SHORT BODIES. THAT IS WHAT I WENT WITH . I AM HAPPY
 

shifter

Full Member
Joined
May 2, 2004
Messages
181
Loc.
Agua Dulce, CA
Asabadin, thanks for the link. Looking at the photo of the custom rear mounts the top mount looks pretty close to where the duff mounts are or maybe just looks that way in the photo. Are you using the stock bottom mounts? Have you tried them out yet, what do you think?
 

68ford

Bronco Guru
Joined
Dec 26, 2004
Messages
2,710
shifter said:
I have 3 1/2 duff coils with single 7100s in the front and the 360/80 valving is a great match for those springs with the driving I do. Don't worry about the heat, you may be picking up a little from the engine but that heavy valving makes alot of heat. Unless you feel the damping fading it's not a big deal. Wish I could find something for the rear that works as good as the front, been trying to make the duff stage 2 mounts work but don't think the geometry is correct.

you could put bypass shocks on the rear, it will be really good, but then youll want coilovers up front to be equal with the rear. ;D
 
OP
OP
C

ctowery

Bronco Guru
Joined
Jan 8, 2002
Messages
1,024
Loc.
Wellington Nevada
Jeepincj7 said:
That valving seems way light for a coil spring rig with a 351. I used to run 255/75 7100s up front and had to pull them to revalve them. 360/80 is the correct valving for a Bronco on the front.

My EB is about 2900lbs up front.. the 360 is rebound and I feel the problem is compression. Comeing off a ledge the EB will compress way to much in my impression, thats why I was thinking it could also be that the coils do not have a high enough weight rating for MY rig. ?:? ?:? Bilstein still owes me 1 free revalve.

Cary
 
OP
OP
C

ctowery

Bronco Guru
Joined
Jan 8, 2002
Messages
1,024
Loc.
Wellington Nevada
shifter said:
I have 3 1/2 duff coils with single 7100s in the front and the 360/80 valving is a great match for those springs with the driving I do. Don't worry about the heat, you may be picking up a little from the engine but that heavy valving makes alot of heat. Unless you feel the damping fading it's not a big deal. Wish I could find something for the rear that works as good as the front, been trying to make the duff stage 2 mounts work but don't think the geometry is correct.


I don't know how much travel you need in the rear but I used the hoops from Photo-Fab...the ones that Wild Horses buys... and changed the mounting angle. I use 17" #9100rr in the rear, can't see anyone needing more travel :eek: ...24"+. I got pictures posted if ya want to see em.

Cary
 

toddz69

Sponsor/Vendor
Bronco Guru
Joined
Nov 28, 2001
Messages
11,222
shifter said:
Asabadin, thanks for the link. Looking at the photo of the custom rear mounts the top mount looks pretty close to where the duff mounts are or maybe just looks that way in the photo. Are you using the stock bottom mounts? Have you tried them out yet, what do you think?

You are correct-they are very similar to the Duff's mounts. A couple of things I changed when I designed them: my truck doesn't have a body lift and Duff's mounts require a body lift. Also, I haven't laid a protractor on Duff's mounts but I believe these mount the shock a little closer to vertical. I tried to maximize that dimension anyway. The bottom mounts are Currie lower shock mount brackets.

Todd Z.
 

68ford

Bronco Guru
Joined
Dec 26, 2004
Messages
2,710
ctowery said:
I don't know how much travel you need in the rear but I used the hoops from Photo-Fab...the ones that Wild Horses buys... and changed the mounting angle. I use 17" #9100rr in the rear, can't see anyone needing more travel :eek: ...24"+. I got pictures posted if ya want to see em.

Cary

do you have custom alot longer than stock springs? it is physically inpossible that you have 24 in of travel at the spring. stock mounting bronco springs get 14 max(all the way up to all the way down), talked to several spring places, all said the same due to the shortness of our springs. deaver f150 springs only cycle 3 more inches and they are almost a foot longer.
64leafs-01.jpg

64leafs-02.jpg

that setup gets 21 inches with a 64in spring,are springs arent even 50in long.are you measuring from the outside of the tire while articulated? thats not true travel, usually about half, which would be 12in and thats about right.
4linkkit-06.jpg

that setup has 30in, and i have yet to see a bronco with half that, but i would like too. ;D
 

toddz69

Sponsor/Vendor
Bronco Guru
Joined
Nov 28, 2001
Messages
11,222
68ford said:
do you have custom alot longer than stock springs? it is physically inpossible that you have 24 in of travel at the spring. stock mounting bronco springs get 14 max(all the way up to all the way down), talked to several spring places, all said the same due to the shortness of our springs. deaver f150 springs only cycle 3 more inches and they are almost a foot longer.
64leafs-01.jpg

64leafs-02.jpg

that setup gets 21 inches with a 64in spring,are springs arent even 50in long.are you measuring from the outside of the tire while articulated? thats not true travel, usually about half, which would be 12in and thats about right.
4linkkit-06.jpg

that setup has 30in, and i have yet to see a bronco with half that, but i would like too. ;D

I wish someone would make some nice leaf spring brackets/shackles like that for our trucks.

Todd Z.
 

68ford

Bronco Guru
Joined
Dec 26, 2004
Messages
2,710
bolt on 21 inches of travel :eek: ive heard it needs a wishbone to keep the axle from moving side to side though and control axle wrap, but what do you expect with those numbers. ;D you can buy all that stuff, you would just have to weld it on if you wanted to, giantmotorsports.com.
 
Top