• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

full size narrowing

methcat

Sr. Member
Joined
May 28, 2009
Messages
385
Loc.
long beach
can anyone help me fill in my numbers or check what i'm missing?

i found a decent shop to narrow a fullsize housing and respline axles, and ideally they want a sample to copy, but i don't have one to offer, so i want to make sure all my numbers are right. doing various searches, i've come up with:

76-77 BRONCO 11" X 2 1/4" BRAKES: R.H. 29.69" L.H. 27.19"

78-79 axles, both 31.84”

1966-1977 Ford Bronco housing width: 52¼"
1973-1979 Ford pickup 9-inch housing width: 59¾

_______________________________________(76-77)__(78-79)__(difference)
RH______________________________________29.69___31.84_____2.15
LH______________________________________27.19___31.84_____4.65
Overall (less brake offset and carrier gap)_______56.88____63.68_____6.8
Housing_________________________________52.25____59.75_____7.5



I'm assuming that both the 76-77 and 78-79 have the same carrier gap as all 9"(1.125" i think), and both sets would have the same brake offset(wide 11"), so i've taken those numbers out. My thinking was that the difference between the "overall" and the "housing" should be the same, but i'm coming up with 6.9" for one and 7.5" for the other. can anyone tell me what i missed?
 
Last edited:

Bronco Brian

Bronco Guru
Joined
Feb 10, 2006
Messages
1,140
How I did my 60's took overall with 69.25 wanted to 80" over all outside tire to outside tire. be right back need to go find my post on NorCal Broncos.

3 5/8 in the front (per side) and 4 5/8 rear (per side) 3 1/2 Back spacing on the wheels. My guide was to lay the tire & wheel face down and measure to the wheel mounting surface (wms) mine was 9" I knew the wms of the axle was 69.25+9+9=87.25-80=7.25/2=3 5/8 would give me 80" and the same way for the rear.

But with your newer axle I would try to only cut the long side. I think the short side is only 1" longer than mine now. I cut both ends to keep my pinoin pointed to the yoke on the T case. Hated cutting a 79 axle but it's done and just how I wanted it.
Brian
 
OP
OP
methcat

methcat

Sr. Member
Joined
May 28, 2009
Messages
385
Loc.
long beach
But with your newer axle I would try to only cut the long side. Brian

I had planned on taking the longer axles and making them identical to the 76-77 axles, and cutting the housing to match, so that i would just use the 77-75 aftermarket axles as replacements. Is there an easier/better plan?

****edit,

in addtion to checking the above numbers, i had another q, i read this thread where it was said

"You have to cut at least 4" out of 8" or 9" Ford OEM axles in order to shorten and re-spline them. Some of the older axles cannot be shortened at all. You cannot remove 1", 2", or 3" from any stock Ford 8" or 9" axle."

but i 'd swear that i've heard people have both housing and axles taken from f150 full size to EB size... am i just mistaken?

i've been trying to call in to sutton, where i was gonna have the work done, but it's kinda tough to get them on the phone sometimes.
 
Last edited:

siderbox

Bronco Guru
Joined
Nov 5, 2007
Messages
1,119
True about the amount you have to cut in order to respline.
Moser did mine a few months ago.
If you look at the axles, about 4" in they taper to bigger diameter.
As long as the axle does that they can be cut and replined.
From factory they are machined to a diameter then the splines are rolled, displacing the metal.
Opposed to cutting out metal to spline.
Once you see them side by side it is very easy to notice.

When I narrowed my axle:
I shortened one axle so I could get several things done at once.
Driveshaft is dead online with ceterline of engine, trans, and transfer.
Rotated housing to correct pinion angle, mounted spring perches.
Installed housing ends for proper disc brake orientation after rotating housing.
Ended up with 61" wms to wms.

Wanted a wider stance but not as wide as a FW axle would have given.

Now to get the front to match.
 
OP
OP
methcat

methcat

Sr. Member
Joined
May 28, 2009
Messages
385
Loc.
long beach
so what do you wind up with for axle lengths? did you cut one to be equivalent to the short 77 side and then use another factory length on the long side? or are all your axles custom length?

thanks

seems like if you want to have both resplined, it's better to just skip up to this housing...
69.25" 1977-1986 Ford E-150 Van, then they can just size to whatever you want. i'm interested in what you came up with for lengths, there's got to be some smart options for centering/using available lengths, etc with a resize. too bad there aren't as many "factory axle shaft length" charts as there are housing charts....
 
Last edited:

Apogee

Contributor
Bronco Guru
Joined
Nov 26, 2005
Messages
6,348
Loc.
Tangent, OR
I'm running my F150 axles at 1/2-ton PU width, so I'm no help with your axle dilemma, however Ron Sutton has been at www.pro-touring.com a fair amount lately, so you may want to try PM'ing him there. I think he's a forum sponsor.
 

siderbox

Bronco Guru
Joined
Nov 5, 2007
Messages
1,119
so what do you wind up with for axle lengths? did you cut one to be equivalent to the short 77 side and then use another factory length on the long side? or are all your axles custom length?

thanks

seems like if you want to have both resplined, it's better to just skip up to this housing...
69.25" 1977-1986 Ford E-150 Van, then they can just size to whatever you want. i'm interested in what you came up with for lengths, there's got to be some smart options for centering/using available lengths, etc with a resize. too bad there aren't as many "factory axle shaft length" charts as there are housing charts....

I left one the stock 32" and the other cut to 27.1875"

Had to dig through my stack of shop drawings.
I like to draw everything out and write down as much as I can.
So when I put the last few bolts in and it doesn't work, I can find where I screwed up.

http://www.mittlerbros.com/media/pdffile/1000-RENK1_Instructions_1.pdf
This is what I used to do mine.
The last few pages should help. They did for me.
 
OP
OP
methcat

methcat

Sr. Member
Joined
May 28, 2009
Messages
385
Loc.
long beach
Muchas gracias, sounds like a pretty good plan.

Anyone have any guesses as to why my numbers aren't adding up in the first "table"?
 

siderbox

Bronco Guru
Joined
Nov 5, 2007
Messages
1,119
Muchas gracias, sounds like a pretty good plan.

Anyone have any guesses as to why my numbers aren't adding up in the first "table"?

The front is not going to work out so neat and tighty with the use of a stock length axle but It'll work for what I want.

As for the table, I have looked at so many axle and housing length charts and seem to get alot of varying measurements.
I have a chart somewhere that shows no less than 7 different axle lengths for 66 to 77 Broncos.
Mind you most are very close, from a few thousands to a ten different. But They are different.
 
OP
OP
methcat

methcat

Sr. Member
Joined
May 28, 2009
Messages
385
Loc.
long beach
As for the table, I have looked at so many axle and housing length charts and seem to get alot of varying measurements.
I have a chart somewhere that shows no less than 7 different axle lengths for 66 to 77 Broncos.
Mind you most are very close, from a few thousands to a ten different. But They are different.

yeah, that's why i was only trying to compare the 77-76 to a FS, as it "should" have the same brake offsets. it seems like i'm missing 0.7" somewhere.

my logic was, if i had a 78 rear, and tried to make it a 77, i'd have to take the same amount out of the housing as the axles, and that's not the numbers i was coming up with....
 

t120r

Contributor
Sr. Member
Joined
Nov 25, 2008
Messages
643
I was thinking of the same thing.. I wanted to narrow my '79 full width to '77 EB width. That way I could use off the shelf shafts with no problems. Doesn't seem that simple though.
 

u10072

Bronco Guru
Joined
May 18, 2007
Messages
2,249
In order to use both the factory driver/pass side EB axles you have to narrow both sides of the housing. That really only makes sense if you already have a sexy set of cromo axles or something. If you want to want to buy the cromo axles you need 1- inner EB pass and 1- inner f150 Driver side. Once you figure out where to cut the housing off I slide an inner EB pass side axle into insure the inner contact with the gears matches where the outer portion fits up to the outer "C" The tolerances on all this stuff is stupid loose so you would be perfect on your numbers and still be off. If you check your numbers at the balljoint numbers your passenger side will be too short-- because the driver side is 1" longer than the inner EB. Its kind of confusing but if done right it works out about perfect. Personally I ire on the side of too long as its easy to shorten and almost impossible to make longer! I have my own technique for narrowing a housing but the first one can be kind of nerve racking-- measure 5 times and cut once :)
 
OP
OP
methcat

methcat

Sr. Member
Joined
May 28, 2009
Messages
385
Loc.
long beach
I left one the stock 32" and the other cut to 27.1875"

well, i picked up the rear finally, and i think i'm going down this route... looks like its just cut 4.65" from both one axle and the drivers side housing. any thing else? what tires /rim size are you running? i was kindof not hoping to have to go to silverbacks, but i'm guessing i'm gonna have another inch or so of stickout...
 
Last edited:

bigjhoov

nobody
Joined
Apr 10, 2005
Messages
3,583
I would build the housing as desired and measure afterwards for the shaft lengths. Thus, eliminating any guesswork in the matter.
 
OP
OP
methcat

methcat

Sr. Member
Joined
May 28, 2009
Messages
385
Loc.
long beach
I would build the housing as desired and measure afterwards for the shaft lengths. Thus, eliminating any guesswork in the matter.

that would probably be easiest, but i really want to be able to get stock length, or easily orderable replacement shafts.
 

bigjhoov

nobody
Joined
Apr 10, 2005
Messages
3,583
Good thinking. Just go 35 or 40 spline and you won't have to worry about it, lol.
 

siderbox

Bronco Guru
Joined
Nov 5, 2007
Messages
1,119
well, i picked up the rear finally, and i think i'm going down this route... looks like its just cut 4.65" from both one axle and the drivers side housing. any thing else? what tires /rim size are you running? i was kindof not hoping to have to go to silverbacks, but i'm guessing i'm gonna have another inch or so of stickout...

I put new housing ends on both sides so my cut measurements are different than what you'll have.
But the end result should be the same.

As for wheels and tires, I don't have anything on it yet.
It's still in the multiple location state.
The frame is in the garage, the body is in the trailer, the engine is still in the mustang, and the trans is in the corner.

I have a few sets of wheels and tires. All close to the same 'size'
15x8s w/ 35 12.50s, 15x10s w/ 36 12.50s, and 17x8s with 35 12.5s.
So it'll be one of those.

Seems like I'm with you on your line of thinking.
I wanted the benefits of the FW with out the FW stick out.
I'm not a fan of the silverbacks so that wasn't an option for me.
So I kinda let it all meet in the middle.
I'll have, by my calculations, just a bit over an inch more width on each side versus stock EB width.
And believe me I've done alot of measuring and calculating of the last few years.
 

Crawdad

Bronco Guru
Joined
Feb 16, 2011
Messages
3,635
I too would like a lil wider stance while keeping all fenders uncut. I have access to FW axles from a 77 F150 but decided not to go that route. I think I may end up going the cheaper and less modified option by using 1" spacers at all 4 corners. Good luck in your mods!
 

bigjhoov

nobody
Joined
Apr 10, 2005
Messages
3,583
So, maybe I'm missing something here. What advantages are you trying to gain by using the full width and cutting it down? Can you not find an eh width 9"?
 
Top