• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Gas Gauge issues.

editgod@hotmail

Jr. Member
Joined
May 28, 2006
Messages
133
Loc.
LA
Morning everyone,

So my gas gauge has just started to get temperamental on me - its full, its not full, its sitting on E ...

Where do i start in trying to fix this, do i just drop the tank and check everything there or is there something else I should look at first?

I have a single tank, not two.

Thanks.


Guy
 

BroncoJimbo

Contributor
Long-term owner
Joined
Jun 11, 2014
Messages
291
Loc.
North GA
The easiest thing to do is to check all your connections. The wires to the sending unit in the tank and the ground. Clean them all really good and see if that helps.
I have intermittent issues with my fuel gauge too... sometimes it works sometime it don't.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Also, the quick way to test if your gauge is capable of the full sweep is to ground out the sender wire. When you do that, the gauge will normally peg at full.
Don't leave it that way for long of course, and don't be surprised if the gauge takes a few moments to go to full and does it in fits and spurts. It's just the stock IVR cycling and the gauge's designed-in dampening.

Do you have dual tanks? If so, the dash mounted switch is often worn out and needing either a rebuild or a replacement.

Paul
 
OP
OP
E

editgod@hotmail

Jr. Member
Joined
May 28, 2006
Messages
133
Loc.
LA
Thanks Guys,

Tried cleaning the ground wire but still no luck and the tank is full of gas so will have to drive it round and empty it before I can drop the tank and access the sender unit.
Will get back to you when I have an update.

Guy
 

pcf_mark

Bronco Guru
Joined
Jun 11, 2010
Messages
3,697
Did you ground the sensor as DortDonk said. You could have a bad gauge. Or wiring.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Yeah, I didn't mean to make sure the ground was good, because the sending unit is still in-between the ground and the gauge.
To test the gauge itself, you need to take the gauge side of the circuit and ground it directly.
To do this best (checking both the gauge and the wire to the sending unit) you pop the plug off the sender at the front of the tank and put a jumper wire in the socket for the gauge and touch it to a good ground.

Yes, you are in effect short-circuiting the positive voltage side to ground. But because you have a resistor inline (the gauge itself) you don't get a spark or a blow fuse or melted wire. Like you would if you simply put 12v to ground through a wire.

The gauge protects it, and reacts by the needle raising to beyond the full line.

Paul
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
If you check it up at the gauge itself, or at the selector switch (if you have 2 tanks) then you're still testing the gauge, but not able to test the wire between the switch and the tank sending unit.

And I think it's easier to get under the truck and pull the connector than it is to turn myself upside down again and hook up probes and wires under the dash.
Been there, done that way too many times!

Paul
 

pcf_mark

Bronco Guru
Joined
Jun 11, 2010
Messages
3,697
Grounding it at the tank eliminates everything but the sender - sounds like the best way to test it. Taking the take out sucks I would check everything else first!
 

riggermortis

Jr. Member
Joined
Jan 31, 2016
Messages
88
As long as we're talking about a stock tank, you do not have to drop the tank to remove the sending unit, it comes out through the front of the tank.
 
OP
OP
E

editgod@hotmail

Jr. Member
Joined
May 28, 2006
Messages
133
Loc.
LA
Hey,

So I don't think i have a stock tank, I remember years ago I dropped it to change the sending unit that is on top (it was a pig to do) and there is definitely only one. Yes I only checked the ground under the chassis as it was dirty and I was very optimistic it would be an easy fix.
I will pull the wire of the back of the gauge and run something from the gauge to ground and see if the needle maxes out (if i am understanding you all correctly).

Standby for an update...


Guy
 

wegngis

Full Member
Joined
Sep 2, 2008
Messages
317
Loc.
Oregon
I've had trouble with my gauge too, but it simply reads 'empty.' I'm getting resistance back there, almost like I got a hole in the float and it's just resting on empty. You know how there's the ' key off' position for the gauge, then it comes up ever so slightly when you're on E? That's what I mean. I kept thinking I needed to pull the tank to get that sending unit out, but I should look again, there's probably room if I draw the level down.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Yep, if it's a stocker you should be able to do it pretty easily. Relatively speaking that is!
The word "easy" and old Bronco parts don't always go hand in hand.

Two common things are for the float to get a leak and sink, or the float to literally fall out of it's loop and let the arm just sit there at the bottom.
Of course, it could have failed electrically too, as that's not unheard of either. But you won't know until you get it out.

Good luck.

Paul
 
Top