• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Gas gauge

stupidboy

My wifes porn star.
Joined
Dec 29, 2009
Messages
5,790
Loc.
Morrisdale Pa.
I watch my gas gauge move from far empty to just below "E" when I turn the key on. I have a new sending unit and a full tank of gas but the gauge is not reading that.
What can I do to troubleshoot this issue??
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Lots of things at this point. But some questions for you first.
Stock tank, or aftermarket larger one?
Stock type sending unit, or aftermarket for the aftermarket tank?
Did the old unit read the same?
If you disconnect the sending unit at the tank and ground the signal wire directly, then turn the key ON, does the gauge peg full? This is easy to do with the stock connector.
Multiple tanks with a switch on the dash? If so, do both tanks read the same?

Just a few things to clarify a starting point.

paul
 
OP
OP
stupidboy

stupidboy

My wifes porn star.
Joined
Dec 29, 2009
Messages
5,790
Loc.
Morrisdale Pa.
20 gallon tank that I built aftermarket larger tank sending unit.
I never saw the old one hooked up and working.
I'll disconnect the signal wire and see if gauge pegs.
Just have the one tank.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
All good news so far. Not having the dash switch eliminates one big buggy fitting so you can narrow things down more easily.
Did you happen to test the new sending unit out of the tank after you set it up? Or even more important, did you verify that it was indeed a 73-10 ohm range unit?
If you bought it from one of the Bronco vendors it was likely tested before shipping (we do that) to verify, but it never hurts to re-verify just in case. I know we've occasionally let stuff slip through that we know need to be tested (someone got in a hurry and "assumed" most likely) but things do get tested. Mostly because you never know what's going to come in on an order.
I think we still get front turn signals that are wired backwards from the vendor and have to check/fix every one.

I don't know what a sender rated for a GM vehicle would act like on a Ford gauge, but it would certainly be out of range!

Paul
 
OP
OP
stupidboy

stupidboy

My wifes porn star.
Joined
Dec 29, 2009
Messages
5,790
Loc.
Morrisdale Pa.
I unhooked the connector that goes back to the tank at the firewall and the gauge did nothing at all.
 
OP
OP
stupidboy

stupidboy

My wifes porn star.
Joined
Dec 29, 2009
Messages
5,790
Loc.
Morrisdale Pa.
So I unhooked the orange wire off the gauge and put a jumper on it right to ground and the gauge movers to beyond full so that means the gauge works.
I’ll check and make sure I have good ground at the tank.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
When you disconnected the connector at the tank, you need to jumper the two connections together, basically connecting the sender wire to ground. This mimics what you did up near the gauge but confirms whether or not the rest of the wire is good all the way back to the tank.
 

Rustytruck

Bronco Guru
Joined
Feb 24, 2002
Messages
10,872
the tank sending unit is a variable resistor to ground. it limits the ground signal to the gauge you probably have to adjust the swing of the float. needs to adjust the float out and up so it tops out close to the top of the tank. Maybe its contacting something inside the tank like the vent or fill tube limiting travel which sending unit did you use one for the main tank or one for the side tank? origional Ford were 2 different units.
 
OP
OP
stupidboy

stupidboy

My wifes porn star.
Joined
Dec 29, 2009
Messages
5,790
Loc.
Morrisdale Pa.
After doing all the checks we discussed I ended up draining the tank and dropping it.
Pulled the pump and sender assembly and plugged it back in to move it in my hand and it worked.
When I built the tank I made a sump for the pump and the float was hitting it as soon as it started to rise.
I bent the float around to where it could make a full unobstructed sweep.
Thanks for the help DD and Rusty
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Fantastic! Lotta hard work on your part, but this time it sure paid off. And at least it wasn’t a bad sending unit or a float that didn’t.
 

i3adme

n00b
Joined
Nov 20, 2020
Messages
26
Literally just went through these symptoms 3 days ago. Turned out my brass float was sunk. Bought the sending unit new from TBP, and never tested the float. Read everywhere to test your new unit before installing, but I didn’t listen and learned the hard way.
 
Top