• Just a reminder that you won't be able to start new posts or reply to existings posts in the Archive forum.

    This is where all the old posts go so they can still be used for reference and searched.
  • Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Good heads?

addicted

Bronco Guru
Joined
Jun 7, 2009
Messages
1,936
Loc.
Broussard, Louisiana
In an effort not to high jack someone elses thread, Im wondering about a good cylinder head choice for a 351W. On a mostly street driven truck, around 9:1 CR, moderate cam, 650 carb. I want strong off idle torque but I dont want the motor to fall on its face after 4000 rpms either. Give me some opinions please. Iron or aluminum doesnt matter. Just want an all around good performing head. Thanks.
 

Hank_

Bronco Guru
Joined
May 9, 2010
Messages
1,915
Dont know what others will say but I picked up a set of GT40's off a 96 explorer. I got the entire motor for $350.00 and figured they would be bettery the the factory 351 heads.


Henry
 

Ratch

Contributor
Sr. Member
Joined
Nov 1, 2007
Messages
695
Dont know what others will say but I picked up a set of GT40's off a 96 explorer. I got the entire motor for $350.00 and figured they would be bettery the the factory 351 heads.


Henry

The explorer GT40P heads are a good choice. Just remember that they have angled spark plugs which limits you choice of exhaust headers. There are a lot of them becoming available in the Pull-a-part salvage yards but you have to pretty much be standing there when they show up. The mustang guys love them and resellers will pick them when they get a chance. I got lucky this weekend and stumbled on a set at a yard and snatched them up for $60. Been looking for a set for a year now.
 

matts70

Sr. Member
Joined
Jul 27, 2009
Messages
443
Loc.
Northwest Indiana
A good question is what year is the block/cylinder heads on your 351? There is quite a difference between say a 1969 351 cylinder head and a 1979 351 cylinder head.

A '69 cylinder head for a 351 will be similar to the GT40 from my understanding, but just about any cylinder head will be better than the late 70s models.
 

Amac70

ME
Joined
Mar 27, 2002
Messages
3,269
http://www.summitracing.com/parts/TFS-51400004/

these are the ones im looking at the most. there right in the middle of everybody else's(aftermarket) heads. being slight larger then the 165's and smaller then the 185's. larger valves but positioned in such away that you can do up to a .550 cam on stock pistons with out modifying them. 61 cc chambers can get 58cc chambers if you want to up compression. I go round and round on head choices but i come back to this one the most.
 

joe

Bronco Guru
Joined
Sep 9, 2001
Messages
1,932
best bang for the buck would be the aluminum Edelbrock Performer. IMO

these heads are time tested and have been out for literally decades and I cant recall anytime I've heard any bad thing about them.

no there nothin special, just a great all around add on. they flow better than any stock cast head and run cooler for today's low octane fuel.

also unless you find a deal that's good to go, add up the cost of rebuildin a set of cast heads and compare it to a bolt on, outa the box, after market head.

my two cents
 

trailpsycho

Bronco Guru
Joined
Dec 11, 2003
Messages
4,856
Hands down, if you can afford them, AFR 185s would be what I would run...might talk to some engine peeps, the AFR 165s might also do the trick on a standard bore 351W. A little pricy, but a top performer at all rpms.

Those TFS heads, mentioned above, are also GREAT. Asolid choice as well. The Edelbrocks tha Joe mentioned are good and may be a hundred or two cheaper.
 

reynard101

Bronco Guru
Joined
Aug 19, 2006
Messages
1,098
I like the AFR 185s. The 185 intake runner volume will keep the low RPM torque there, good for 4x4, off the line acceleration, and daily driving. While the heads still flow well for higher RPM stuff.

GT40 and GT40P stuff is good too. But if you need to rebuild the heads it starts to add up and while the cost is not as expensive as buying new heads, but it starts closing gap - sometimes quickly depending on what needs to be done.
 

Terkish

Sr. Member
Joined
Feb 22, 2008
Messages
414
On a 351w mark my vote down with the AFR 185's. great all around head, low rpm torque and good high rpm power.
 

matts70

Sr. Member
Joined
Jul 27, 2009
Messages
443
Loc.
Northwest Indiana
There's an article out there somewhere on the Internet in which they bolted, I believe, AFR 185 cylinder heads onto a late 60s Mustang 302 and put it on a dyno. The cylinder heads alone added 100 HP, if I have the correct AFR model #. It's an article on cheap horspower for a small block Ford. They also added a VERY MILD intake and 4 barrel carb, but that was about it. They were pricey, though--$1500 or $2000, if memory serves me correct.
 

blubuckaroo

Grease Monkey
Joined
Jun 11, 2007
Messages
11,796
Loc.
Ridgefield WA
I can't believe that a daily driver with less than 9.5 compression and a hydraulic cam will benifit from aluminum heads over a set of cast iron World Heads. I'd use Windsor Jr on a 302 and Windsor Sr on a stroker or 351. The benifit is the strength of the iron casting and threads. If it's the trick look your after, just buy a can of Krylon.
 

Amac70

ME
Joined
Mar 27, 2002
Messages
3,269
the world heads are only 75 dollars cheaper (then trickflow's) i think i would pay that 75 bucks for the wieght savings. I am already nose heavy any savings is a plus.
 
OP
OP
addicted

addicted

Bronco Guru
Joined
Jun 7, 2009
Messages
1,936
Loc.
Broussard, Louisiana
Thanks guys. Those are all the heads I've been looking at. lol. I looked at the AFRs but I was concerned about them being maybe too big. And I dont want to error going too small either. My block is a 71. I have a new Scat crank, Eagle rods, and some Speed Pro forged aluminum pistons that are supposed to give me around 9:1 with 64cc heads, which is exactly what I was looking for. Only problem has been trying to find good 64cc heads. So Im ditching the forged pistons in favor of some lower compression KB hypers which opens up my head choices a little more while being able to keep my CR at an acceptable level. All the good aluminum heads are within a few hundred dollars of eachother so Im not concerned with the price. I also am looking at some iron heads from World and Dart. Its just so damn hard deciding! Aluminum is lighter. Iron is stronger. So I could really go either way. My biggest goal is off idle to say 5000rpm. I already have a Edelbrock AVS 650 cfm carb and a DUI dizzy also so I want a head and manifold combo that will work with them. So! Any more advice based on all that? lol. Sorry to be so long winded. I just really want to get this all right the first time. I've seen too many motors not perform like they should because the parts didnt compliment eachother. I want a nice semi mild motor for dayly driving and still be able to roast 35s if I get a wild hair up my butt ;D Is that even possible?? Thanks guys.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,114
Trickflow
Had them on the last 351. Ran from idle to 6000 with power everywhere. Started with a carb and ended with a throttle body EFI, worked with them all.
 

bigcountry

Contributor
Bronco Guru
Joined
Nov 3, 2009
Messages
1,206
With 9:1 compression ratio at 64 cc, you would be fine to go up to 9.5:1 compression with smaller cc aluminum heads. You will still be able to run pump gas without having to change the pistons.
 
OP
OP
addicted

addicted

Bronco Guru
Joined
Jun 7, 2009
Messages
1,936
Loc.
Broussard, Louisiana
I dont just want to be able to run pump gas. I want to be able to run 87. Lol. I dont know if that realistic but its what Im shooting for. And I was originally building the motor for another project and wanted to be able to spray it. Thats the only reason I wanted forged pistons. Besides there being a limited selection of 64cc heads, I dont want to hear cold start piston slap. I buddy of mine wants them so no biggie. Hypers are cheaper so it will pretty much be a wash money wise.
So in aluminum heads it looks like a tie so far between Trick Flows and AFR. What TF offering is close to the AFR 185? There seems to be a few different ones to choose from. And what would be a good intake manifold to go with them? Im assuming something like the Edelbrock Performer RPM but Im not sure if I will have a clearance issue with that big DUI dizzy. Thanks again guys.
 
Top