• Just a reminder that you won't be able to start new posts or reply to existings posts in the Archive forum.

    This is where all the old posts go so they can still be used for reference and searched.
  • Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Installing New Mechanical Fuel Pump

Chief Master Sergeant

Retired U.S. Air Force
Joined
Nov 6, 2002
Messages
5,222
Can someone give me some advice on installing a new fuel pump? I paid close attention to how the old one cam out, but the new one doesn't seem to want to go on properly. The bottom edge is sticking out about an eigth of an inch.
 

don parris

Jr. Member
Joined
Dec 19, 2003
Messages
95
Loc.
cumming ga
turn the motor over about 1/2 turn to get the fuel pump cam on the low spot dont try to force it you can break the pump
 
OP
OP
Chief Master Sergeant

Chief Master Sergeant

Retired U.S. Air Force
Joined
Nov 6, 2002
Messages
5,222
I'm kind of new at this, so I'm not sure what the eccentric is. My Hanes manual shows it, but due to the location, I can't see inside to tell. I know I probably sound like a dumb @#$, but I just want to make sure I am doing this right.
 

ROKDWLR

Bronco Guru
Joined
Dec 3, 2003
Messages
1,016
Loc.
Stockton, Ca.
flint_knapper said:
jeepster,

thats a good "cutaway" !!!

I agree. 3 cheers for
 

Attachments

  • B11165.jpg
    B11165.jpg
    40.5 KB · Views: 53
OP
OP
Chief Master Sergeant

Chief Master Sergeant

Retired U.S. Air Force
Joined
Nov 6, 2002
Messages
5,222
Okay, maybe I'm not holding my mouth right. I manually turned the motor and tried to install and every possible angle. The bottom edge of the pump will still not line up properly. I even tried to put the old one back on and it's doing the same thing. The whole pump seems to want to settle about 1/2 inch lower than where it should. What am I doing wrong?
 

jbeyer

Bronco Guru
Joined
Mar 3, 2004
Messages
1,679
Loc.
new york city
Jeepster said:
post a pic. There isnt that much to them. stick it in there and tighten em up.

if you can make it seat by hand without using too much force, its good to go.
the last fuel pump i got had a warning in the box that said to be sure it was a 302 pump and and not a pump for a 351. the arms were slightly different. for paranoias sake, you could be sure the old one and the new one match.


jeepster, ive always been meaning to ask- do you have a jeepster? i have a soft spot for all those old willys/amc products. must be the home town connection.
 
OP
OP
Chief Master Sergeant

Chief Master Sergeant

Retired U.S. Air Force
Joined
Nov 6, 2002
Messages
5,222
Well.....It's on, but I don't think it corrected my problem. I had a post out awhile ago on the subject, so I sahll go back to it for answers. Thanks Jeepster!
 

NYLES

Bronco Guru
Joined
Aug 13, 2004
Messages
9,846
Rockdwlr

Just wondering what you think about that carb? I have built about a 350 hp 302 needs a carb headers and ignition and maybe itll crank. And by the way your gallery is awsome nice ride.
 
Top