• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Is kick panel hole necessary?

Thaddeusrex

Contributor
Jr. Member
Joined
Sep 15, 2023
Messages
67
I’m rebuilding where the driver kick panel, A pillar, rocker, and floor meet. The kick panel has a 1 5/8” hole at the bottom. I don’t know what it is for. It is on replacement kick panels, but I’m just rebuilding these, not buying new. Is it necessary? I don’t want it if not necessary, this is a restomod, not concourse stock.
 

Attachments

  • IMG_0840.jpeg
    IMG_0840.jpeg
    219.4 KB · Views: 191
Last edited:
OP
OP
Thaddeusrex

Thaddeusrex

Contributor
Jr. Member
Joined
Sep 15, 2023
Messages
67
Thanks PCB, any idea what the big one is? I looked at my tear down photo log, and they weren’t being used.
 

PCB 4x4

Contributor
Sponsor/Vendor
Full Member
Joined
Feb 14, 2025
Messages
247
Can't say I've seen the larger one on any of our builds.
 
OP
OP
Thaddeusrex

Thaddeusrex

Contributor
Jr. Member
Joined
Sep 15, 2023
Messages
67
Very interesting. Thanks James! They’re a gonner then. I’m curious how you know? That’s pretty obscure info.
 

jamesroney

Contributor
Bronco Guru
Joined
Sep 11, 2007
Messages
2,607
Loc.
Fremont, CA
Very interesting. Thanks James! They’re a gonner then. I’m curious how you know? That’s pretty obscure info.
Well, when I replaced my first kick panel, (made by myself) I used the hole to align the two pieces together, and spot welded that sandwich. Then I got this idea to pull the tub and media blast the frame. But there was no easy place to lift the tub, and I couldn't use a strap without a spreader since the outer rockers weren't there.

So I used a spreader and lifted the body with those two holes and a hoist. So I ASSUME that the factory did the same. I could be wrong. I guess my question would be: "where else could the factory lift a painted body?" After stamping, after weld, after paint, but before assembly. (Fenders on, hinges on, Doors off, aprons on, core support on, floors, rockers, quarters and bed on, windshield on)

So I don't actually KNOW...but I have a decent Guess.

Edit...(maybe they used those holes for lifting when the tub is inverted?)

I go to great pains to install the holes, and make the sandwich. It is worth pointing out that the reproduction kick panels (that I've installed) have the wrong size hole, and it's in the wrong place.
 
Last edited:
OP
OP
Thaddeusrex

Thaddeusrex

Contributor
Jr. Member
Joined
Sep 15, 2023
Messages
67
Oh, that changes things. This body is going to have to come on and off a couple times so I can complete the chassis welding once I verify ride height/level with body weight on. Also, I’m going to have the body and paint finished at a shop who might need to. If those are needed, maybe I should put them in.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
You probably won’t be verifying ride height very accurately with just the body. If that’s what you meant.
It’s gotta be literally everything. From hardtop to bumpers, engine to interior. Is that how you’re gonna be removing the body? Or is it just the interim body only?
If body only, I wouldn’t put too much stock in the measured height.
 
OP
OP
Thaddeusrex

Thaddeusrex

Contributor
Jr. Member
Joined
Sep 15, 2023
Messages
67
Yes, I realize that. i know I have to pile everything on. Frankly, I don’t know how I’m going to do it yet. I really wanted to just finish weld the chassis and be done with it, but the Duff guys are super insistent that that would be a big mistake, so I'm trying to follow directions.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
The alternative method to that, is to compress the suspension to the expected ride height, and lock it down. Work with everything from there while mocking things up. The body can come and go as needed at that point.
For example, if you’re going with a 3 1/2 inch lift, you can set the front suspension height at 10 1/2 to 11 inches between the top of the axle tube and the bottom of the frame rail.
In the rear you would do it 9 1/2 to 10.

The nice thing about doing it this way is you don’t even have to have the suspension installed completely. If it is, you can simply compress it with ratchet straps to the desired height.
If it’s not, you can weld or otherwise attach bars/tubes/blocks between the frame and axles to set the ride height solid while you work on the rest of the vehicle.
 
OP
OP
Thaddeusrex

Thaddeusrex

Contributor
Jr. Member
Joined
Sep 15, 2023
Messages
67
Yes, I did that, i built the chassis at the expected ride height with the numbers you mentioned too actually. Duff said I should still just tack weld the frame brackets, diff housing bracket, and spring retainers on though. Then, when I have the fully loaded truck sitting on the chassis, verify that its the right height and level, then remove the hole body, cut tack welds and adjust if necessary, and then make permanent welds. I sure don’t like it, but that’s what I’m doing. I don’t know how I’ll lift the body yet when I have the whole thing built and sitting on the chassis. That’s a year or two away btw.
 
Top