• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Is this "normal"

EricLar80

Bronco Guru
Joined
Jun 14, 2001
Messages
2,170
You need to:
  1. Remove wheels, hubs, axles, and tie rod
  2. Shove a towel between the pinion and ring gears, and then turn the gears. This will pop out the differential. Keep the shims on either side in order.
  3. I would remove the pinion to keep rust debris off it
  4. Get a brass wire wheel on an angle grinder or drill and go to town on the inside of the case. Don’t hit the machined surfaces.
  5. I’d probably hose it out really good to remove all debris. Dry with a towel and compressed air. Spray liberally with WD-40.
  6. Inspect the ARB and clean the ARB. Replace seals and bearings as required. I’d probably toss the whole unit if the seal surfaces were damaged enough to cause air leaks.
  7. Reassemble

It can all be done without removing the differential housing from the vehicle.

I wouldn’t worry about how it happened if you didn’t go in deep water. I’d just use 4wd a few times a year and get a good coating of oil on the inside. That will keep it looking like new in SoCal.
 
Last edited:
OP
OP
FORD*DIEHARD

FORD*DIEHARD

Contributor
Sr. Member
Joined
Sep 20, 2018
Messages
353
I added additional pictures , trying to get different/better angles if it helps.

So after a long sleepless night thinking about this, I looked at the fluid that came out and did a test. Also just thinking, if the wheel seals were bad wouldn't there be fluid leaking from the (yoke-rhinks that's what its called". I dont see any fluid at that point.

I poured some water in it and it bubbled up, which is not how it looked when it came out. So could the shop have not put in the right fluid to cause this, or any fluid would work as long as the gears are engaged and run through it to coat?

As some have mentioned to just put new fluid in and run it , drain and replace fluid. If parts are already damaged , what is the worst that can happen if I tried that? It sounds like everything already has to be replaced, is it worth a shot?

How would I know if this does work or doesnt work?

I am not questioning anyone's opinion, just on a budget and if I can make it work for now until I can save for this to do it right.

Thank you in advance for everyone s time/help,

Sonny
 

Attachments

  • 20201221_123335.jpg
    20201221_123335.jpg
    135 KB · Views: 44
  • 20201221_123313.jpg
    20201221_123313.jpg
    134.2 KB · Views: 41
  • 20201221_123252.jpg
    20201221_123252.jpg
    66.2 KB · Views: 41
  • 20201221_123240.jpg
    20201221_123240.jpg
    80.6 KB · Views: 40
  • 20201221_123807.jpg
    20201221_123807.jpg
    95.4 KB · Views: 40

nvrstuk

Contributor
Just a Bronco driver for over 50 yrs!
Joined
Jul 31, 2001
Messages
10,622
Loc.
PNW
What EricLar said...

I totally understand budgets. Pop it out, cover the pinion to keep crap off it, clean it all up and give it a shot. The rust doesn't look like it's deep enough in these pics by to be a serious problem.

Carmel colored oil means the oil and water have been mixed. I buy I/O boats after the blocks haven't been drained and the oil in the block is carmel colored and frothy from oil and water being mixed by the crank & rods. :(

Give it a try.
 

maverickconner

Sr. Member
Joined
Mar 16, 2004
Messages
485
These guys are right, obvious water contamination. If the fluid looked like bad chocolate milk you know for sure. I would definitely tear it apart and put new bearings at least in it. I'd assume that the gears would be whining at this point too. The gear run surfaces surprisingly do not look pitted or burnt. But looking at that little bit of fluid on the ring gear- water.
 

jamesroney

Contributor
Bronco Guru
Joined
Sep 11, 2007
Messages
2,607
Loc.
Fremont, CA
I'm going to disagree here.

Your axle is rusty from free oxygen (and moisture) in the air. It is NOT from water in the oil, , or from driving in water. People forget that water is heavier than oil. when you get water in your axle housing...it goes to the BOTTOM. It does not float on top.

If you have water vapor in your housing, and you don't have adequate ventilation...and you don't pull that 4wd lever in the cab once in a while...then this happens. You have basically created a Terrarium in your axle housing. And pretty much every day...the water condenses inside. The continuous cycle of cooling and heating causes it to "rain" in your housing all the time. You see it more in climates where you get big temperature swings. LA is often cold at night, and warm in the daytime. (You will notice that all of your rust is ABOVE the oil level line...)

It is kind of interesting that the items with different thermal mass, and different thermal conductivity (like the ring gear, and ARB end cap...) have different levels of corrosion. That's because the dew doesn't fall there...

I like regular 90 wt petroleum based gear oil. It sticks to everything, and doesn't hold moisture. But anything will rust in a Terrarium.

I would also do what NvrStuck said above...I'll bet that ARB is just fine inside.
 
Last edited:

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,112
That second round of photos actually looks even better. Much cleaner parts than what we saw in the first round of pictures.

My only worry is the rust coming off and mixing with the oil. Not huge flakes of it. The grit of it. Rust is abrasive. Think of mixing sand with the oil.

After looking at the new pictures, I probably wouldn't bother pulling the pinion. Pull the carrier, dismantle, rust restoration product (they even have instructions on soaking newspaper or something like that to clean the housing).

The oil probably lacked or used up the anti-corrosion additives. My daily driver truck I like to run it hard enough a couple times a year to get the diff oil up around 200°+. Drive any moisture out. Pretty much impossible to do in the front axle.
 
OP
OP
FORD*DIEHARD

FORD*DIEHARD

Contributor
Sr. Member
Joined
Sep 20, 2018
Messages
353
Thank you everyone for your replies. I am going to be working on this at the beginning of the year with some help. I will update what we find.

Sonny
 
Top