• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

LOWERING my Bronco

behemoth

Bronco Guru
Joined
Jul 2, 2003
Messages
1,736
No real progress at all I stopped to allow the neighbors a chance to calm down. I figured out which one it was and now I know her work schedule, so I have a time frame now in which to work. It sucks but until I become a committee member myself I have no voice.


That sheet has a the 3 measurements that do not change. The 8 7/8" the 9 1/4" and the 3 1/2" So we are pretty much stuck with this height, unless you want to notch the frame in the front to drop the mounting point down some.

You said that Dale is having some height issues and he is using a threaded rod for adjustment. Is it that the height is actually too low for us?

So I will be working on it but it has slowed down a whole lot. I will be stripping the firewall and cleaning up what I can. Then when I pull the body to do some other work I will get going on the suspension again.

I am also looking at the 4 link for the rear as well since my stock springs are done.

Bill
 
OP
OP
greatguy57078

greatguy57078

Contributor
Bronco Guru
Joined
Jul 15, 2006
Messages
3,430
The only reason that Dale is using threaded rod is to get a veiw of what he wants it to look like. Something similiar to what you have done in your previous pics. His concern is he is not sure where it will set exactly until he gets the weight of the engine etc. added to the front end. I have not heard from him a whole lot this winter, but I am sure he will be sending more info and pics as the weather warms up.
 

behemoth

Bronco Guru
Joined
Jul 2, 2003
Messages
1,736
I will probably get started on it more next weekend, this weekend I have the scout fair and fabulous fords. I wanted to have it ready, but between the actual job, some parts delays and money I just could not get it done.

My concern is that the front will be to low, requiring a new cross member and a notch up front but we will see.

Bill
 

Bronco_Rider

Full Member
Joined
May 22, 2002
Messages
190
Loc.
Brentwood, Ca
I would consider running an IFS with an upper and lower control arm from an all wheel drive S10 or a later F-150 or the like.
It could be lowered and 4 wheel drive. The best of both worlds

If you are going to do it, go for the full impact!

Bronco_Rider
 
OP
OP
greatguy57078

greatguy57078

Contributor
Bronco Guru
Joined
Jul 15, 2006
Messages
3,430
What size are the tires you went with in the pics? Are they the OEM Mustang 17x8 with the 235 tires? I am wondering how wide I can go. No sense in trying to squeeze more underneath than I can fit, unless I narrow the rear first....right?
 

behemoth

Bronco Guru
Joined
Jul 2, 2003
Messages
1,736
I went with stock mustang take offs, 17x8 with the explorer rear that is about it unless you get some extreme backspacing or offset tucking it all under. narrowing the rear would allow for more wheel, but then suspension will need to be modified. the rear leafs need to be from what I have seen with mine a small leaf pack with some kind of lift. My old stock ones are just done flat.

The front is already narrowed to 56" so the room is there.

I will be ordering a new rear suspension, I am going to go with the triangulated 4 bar and bilstein rod shocks ( coil overs ). This is unless someone can convince me that there is another easier better idea.

Exhaust routing is going to be a pain with this but I want to get the rear lower than the 3" rake that I have seen on a few of them.

Lots to do no money left at this point and it is also soccer season as well as home repair season for me. I have a whole lot of repairs to do to the house to keep the wife happy.

The front and rear bumpers will be narrowed, the hood changed, no chop as I am 6' and I do not want to cut the floors that I just put in.

There will not be a half cab or a full top on this one, just going to leave it topless.

I am thinking about 90s honda accord mirrors when I remove the frames.

I hope to get the body lifted off next weekend so that I can fit the front suspension as well as the c notch. Then the scraping and painting will begin.

Blacked out engine bay and cleaning the frame.
 

77bronco_ed

Bronco Guru
Joined
Jul 3, 2004
Messages
1,793
Wow it looks like I have a lot of reading to do to catch up on this thread...
Unfortunately I hit a financial snag... so things have just plain stopped.

I bought the shortened rear /with disk set up... and I am planning on purchasing the 4 link set up shortly. Here is the one I am thinking about...
http://autoweldchassis.com/lskits.ivnu

A little repositioning of the wheel tubs will allow up to 18.5 wide tires to be tucked between the quarters and frame. With the link option you can make height adjustments. I was also thinking that topless would be nice.
(but... only with the chopped windshield frame that will still accept the chopped half cab :)

I would have got the link set up but I opted for a new compressor first...

Looks like there is a lot of thought going into this on the board.


I am afraid that if I keep reading this thread I may use my charge card

-Ed
 
Last edited:
OP
OP
greatguy57078

greatguy57078

Contributor
Bronco Guru
Joined
Jul 15, 2006
Messages
3,430
With the warmer weather finally here, I have been making some progress. I work on what I can. I am about broke, but I have enough parts that I had bought here and there laying around to keep me going. It helps to have a brother in the parts business.
I have the Explorer rear end cleaned up and painted, and will install the new brakes this weekend hopefully. I have also been working on knocking all the old paint off the halfcab I am going to chop. It is not in perfect shape, but a good enough candidate for a chop job. I am stripping off what I can so they can sandblast the rest off in the tight spots. I will be taking 3" right out of the middle of it. I am only 5'6", so squeezing into the cab won't be a problem.
I hope to have a rolling frame here sometime soon, so I can start the Mustang II installation. Pics below...
 

Attachments

  • top1.JPG
    top1.JPG
    67.1 KB · Views: 124
  • TOP.JPG
    TOP.JPG
    77.5 KB · Views: 107
  • rear.JPG
    rear.JPG
    109.2 KB · Views: 131
  • 100_4711.jpg
    100_4711.jpg
    95.4 KB · Views: 108
Last edited:

77bronco_ed

Bronco Guru
Joined
Jul 3, 2004
Messages
1,793
My plans were to move the wheel tub even with the frame... However If the frame needs to be altered for ride height it may be best to move the tub another few inches to the inside of the frame in order to hide the frame modifications if necessary. Still will hint of a stock pick up bed, without a seat.

If you are going with a link suspension you have a lot of options if you also want to shorten the rear up a bit. I still want to have more tire under there... I guess I am looking @ a cross between what I see in "Dales" and of a "pro street" look.
 

behemoth

Bronco Guru
Joined
Jul 2, 2003
Messages
1,736
Through out this all of the measurements have been done many times. Measure twice, weld once they say on the instructions. Well crap, you go to a whole lot of work to figure out where you want the truck to sit and they hit you with another measurement.

The hats at the rear must be at a minumum of 1" above the frame rail. The lower control arm bolt hole center at the rear is 8 7/8" below the top of the hat. So again for the bronco there is really no options for height without notching the frame in the front.

Measure twice weld once, this is only after measuring a whole lot more than twice and tack welding just as many times.

So the frame on my truck is apparently not true or level. The drivers side frame rail sits about 1/8" higher than the passenger side.

So the crossmember is supposed to be level, so should I make it level regardless of the frame or level it to the frame? I am leaning toward level regardless of the frame.

A little frustrated as I keep having to cut more out of the crossmember to get the dimensions correct.

Once I get the dimensions correct I will pull it all off and por15 the crossmember arms and hats.

Its getting there though, budget is gone and it is close just needs time.
 

behemoth

Bronco Guru
Joined
Jul 2, 2003
Messages
1,736
Well here are some updated photos of the mess I have in the garage. I have stopped on it for some time. Just took the pictures to show what problem I have now.

I leveled the stand and put the cross member on it to check level on the cross member out side of the truck.

The first photo is of the cross member level or close enough for this.

The following photos are of different points on the cross member that should also be level as it sits. They are not and they should be.

It appears as though the cross member is twisted and one of the lower control arm bolts has been welded in crooked as well. The other funny part is that the lower control arm itself is welded crooked in the opposite direction so it is not going to go in easily.
 

Attachments

  • xmember2ctrlarmtubes.JPG
    xmember2ctrlarmtubes.JPG
    31.6 KB · Views: 82
  • xmemberlftctrlarmblt.JPG
    xmemberlftctrlarmblt.JPG
    26.6 KB · Views: 79
  • xmemberlftctrlarmtube.JPG
    xmemberlftctrlarmtube.JPG
    29.2 KB · Views: 99
  • xmemberltop.JPG
    xmemberltop.JPG
    28.5 KB · Views: 101
  • xmemberrttop.JPG
    xmemberrttop.JPG
    26.6 KB · Views: 163
  • xmemberctr.JPG
    xmemberctr.JPG
    34.4 KB · Views: 129

behemoth

Bronco Guru
Joined
Jul 2, 2003
Messages
1,736
Here are some more shots of the hole, the cross member, the 3* angle plates as well as more levels.

There is also one of the jig thing I made to help figure out what height to cut the cross member. The bottom of the bars should be level. The bar marked rear goes to the rear and is 8 7/8" tall, the other one is 9 1/4". These are fixed measurements from the mustang suspension. The rear one has two tabs welded on it to set the top of it 1 " above the frame rail, this is also a fixed measurement that can not change. There is a line on each bar that shows the spindle center line or height above the lower control arm bolts at 3 1/2" this is also fixed. On the back side which you can not see is the lines I made to show the bottom of the frame. This is the horizontal cut line for the cross member.

I guess I can say it worked, but In the end I still needed to cut more off to get that 1" clearance at the rear. Then more to get it level - ha ha right.

This is also the explorer rear diff that I have now cleaned, I just need to cut some brackets off and remove the spring perches so that I can move them in a little.

The explorer engine is coming together as well, destroyed the timing cover trying to get it off of some corroded bolts. Well not destroyed it can be repaired, just not by me.
 

Attachments

  • morelevels.JPG
    morelevels.JPG
    55.9 KB · Views: 117
  • xmemberjig.jpg
    xmemberjig.jpg
    99.1 KB · Views: 148
  • dside1inchclear.JPG
    dside1inchclear.JPG
    40.4 KB · Views: 112
  • pside1inchclear1.JPG
    pside1inchclear1.JPG
    41.2 KB · Views: 117
  • pside3shim.JPG
    pside3shim.JPG
    35.8 KB · Views: 109
  • xmemberfit.JPG
    xmemberfit.JPG
    57.3 KB · Views: 157
  • thewhole.JPG
    thewhole.JPG
    54.5 KB · Views: 149
  • explorerrear.JPG
    explorerrear.JPG
    60.5 KB · Views: 119
  • xmember2framenfl.JPG
    xmember2framenfl.JPG
    36.6 KB · Views: 116
  • dsideuncut.JPG
    dsideuncut.JPG
    49 KB · Views: 129
  • psidecutout.JPG
    psidecutout.JPG
    44.8 KB · Views: 138
Last edited:
OP
OP
greatguy57078

greatguy57078

Contributor
Bronco Guru
Joined
Jul 15, 2006
Messages
3,430
No, I am not getting much done here. They cut the hours at work, so I have time... but no money. I just thought I would bring this closer to the top. Maybe that will cheer me up!;D
 

behemoth

Bronco Guru
Joined
Jul 2, 2003
Messages
1,736
Not much here either, no money and I do not have a lot of time. I was able to get the cross member out. Heidts sent me a new one free of charge with a call tag to return the other one. It is as I believed, twisted and not true. The replacement is here and the other one is on its way back to them.

I will cut this one and see where I end up.
 

behemoth

Bronco Guru
Joined
Jul 2, 2003
Messages
1,736
Small update as I worked on it some today.

the replacement cross member is installed and level nice.

I dropped the main tank to get at the sender and get a better look at the frame for the rear c notch.

The pictures are of the rear at what I think will be the rear ride height. This was very promising as I was hoping to get at least 5 inches of clearance. It looks like I will get it without cutting the bed.

Lots to do.
 

Attachments

  • dside.JPG
    dside.JPG
    61.8 KB · Views: 138
  • pside.JPG
    pside.JPG
    72.2 KB · Views: 134
  • framedside.JPG
    framedside.JPG
    54.4 KB · Views: 118
  • framepside.JPG
    framepside.JPG
    57.3 KB · Views: 110
  • tube2frame.jpg
    tube2frame.jpg
    62.5 KB · Views: 124

77bronco_ed

Bronco Guru
Joined
Jul 3, 2004
Messages
1,793
No posting here lately... I was able to get my sub panel, and garage wired...
The Quincy air compressor is ready to go. At least I am ready to get moving ;)
 

behemoth

Bronco Guru
Joined
Jul 2, 2003
Messages
1,736
Found more issues with the crossmember for the front, some consistency in manufacturing would be nice. I have also made a template for the steel for the rear c notch. The kit that I bought is more significant than needed. So I will have to cut some steel.

I have also removed the perches and other things from the explorer rear. Now I just need to drop the frame out from under the tub and get back to work.

Slow going now though.

Frame off opens up to many while I am there issues.

Bill
 

77bronco_ed

Bronco Guru
Joined
Jul 3, 2004
Messages
1,793
Slow moving thread now...Time, money it gets tough ;)

At least Marty's friend Dale is moving along on his. It's going to be one Nice Bronco


-Ed
 
Top