• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

LOWERING my Bronco

behemoth

Bronco Guru
Joined
Jul 2, 2003
Messages
1,736
I set it down on the ground to get another look at it and see what the next issue will be.

Looks like the inner fenders will have to go as in these pictures the front tires are sitting on the inner fenders, or the front would be lower.

I also may have to get stiffer springs for the front coil overs but we will see once I get them adjusted. You can see in the photos that the arms in front are not parallel to the ground and the coils are not adjusted or compressed much.

The tank is in and even though it is just a little bigger than the stock tank speed bumps will be an issue. You can see it below the rear diff in one of these pics.
 

Attachments

  • DSC02983 (Medium).JPG
    DSC02983 (Medium).JPG
    98.7 KB · Views: 201
  • DSC02985 (Medium).JPG
    DSC02985 (Medium).JPG
    101.1 KB · Views: 128
  • DSC02986 (Medium).JPG
    DSC02986 (Medium).JPG
    77.4 KB · Views: 132
  • DSC02988 (Medium).JPG
    DSC02988 (Medium).JPG
    31.9 KB · Views: 121
  • DSC02987 (Medium).JPG
    DSC02987 (Medium).JPG
    84 KB · Views: 145
  • DSC02989 (Medium).JPG
    DSC02989 (Medium).JPG
    92.4 KB · Views: 130

behemoth

Bronco Guru
Joined
Jul 2, 2003
Messages
1,736
It will not be this low, I was just putting it down on the ground to work on the coil overs with some weight. The front will sit with the arms parallel to the ground so it will be higher and you will be able to turn.
 

broncomitch

Bronco Guru
Joined
Jan 17, 2008
Messages
2,384
Loc.
west jordan, utah
i want to turn my other bronco into a drag truck soooooo bad!!!!


you all know what that guys problem was right????? or rather why it crashed???





simple.






the FORD bronco didn't like the CHEVY motor ;D
 

behemoth

Bronco Guru
Joined
Jul 2, 2003
Messages
1,736
I keep looking at chopping the top, but with my height that becomes another problem. I have already replaced the floor pans so I do not want to cut them out and lower the floor. The window frames will come off and that should help the appearance. I will at some point drop the hard top on it to take a look at it as well.
 
OP
OP
greatguy57078

greatguy57078

Contributor
Bronco Guru
Joined
Jul 15, 2006
Messages
3,430
A few more high school soccer games and the season is over. Then this coach can hang up his hat and crawl back under the projects. Thanks so much for keeping us up to date Bill (behemoth). It keeps me thinking about all the things I will be doing VERY soon.
 

LilRedBronco

Sr. Member
Joined
Feb 25, 2008
Messages
428
Loc.
Belmont, California
I keep looking at chopping the top, but with my height that becomes another problem. I have already replaced the floor pans so I do not want to cut them out and lower the floor. The window frames will come off and that should help the appearance. I will at some point drop the hard top on it to take a look at it as well.

Gotcha.. I am 6'4 and as I plan out my 32 Ford coupe build my height comes in to it as well. I have a couple of ideas but since it is just in design phase makes it easier.

Regardless it looks great and I really respect how you are approaching this, the whole idea of daring to be different and the different answers you have found to some difficult questions. Really nice job.
 
OP
OP
greatguy57078

greatguy57078

Contributor
Bronco Guru
Joined
Jul 15, 2006
Messages
3,430
I (and the wife) am 5'6 so I have no problem with the height. But...I will be chopping three inches out of the halfcab, and the seats will be about 1" under the top of the roof inside. I am going to remove the auxilary tank and invert the floor on the drivers side. I figure it would be fine for us, but if I was to give a ride or allow someone else (taller) to drive the rod, we would have to make more room. I will be sure to take a few pics, as always.
 

behemoth

Bronco Guru
Joined
Jul 2, 2003
Messages
1,736
Well I will weigh mine tomorrow am hopefully and put this spring rate issue to rest.

All I can say this week is do not get attached to the inner fenders as well as the flat inner fender steel. With the arms flat or parallel to the ground running these wheels and the amount we have lowered the trucks we have a problem.

Now I need to figure out the up travel amount with these systems then I will know how much to clearance the inner fenders.
 

LilRedBronco

Sr. Member
Joined
Feb 25, 2008
Messages
428
Loc.
Belmont, California
I (and the wife) am 5'6 so I have no problem with the height. But...I will be chopping three inches out of the halfcab, and the seats will be about 1" under the top of the roof inside. I am going to remove the auxilary tank and invert the floor on the drivers side. I figure it would be fine for us, but if I was to give a ride or allow someone else (taller) to drive the rod, we would have to make more room. I will be sure to take a few pics, as always.

I have NO idea how you have the energy to coach and do this other stuff. Sometimes I feel like all I do is wake up go to work, travel for work come home at some point after I leave, sleep, wake up and do it all over again. Some of the flights I take for work are 25-26 hours not including lay overs. Those thing suck the life out of me...

Perfect on the picts... I REALLY want to see what that will look like. I am a big fan of stuff like what you guys are doing and I am very curious to see what a chop looks like a 3 inch chop I think will look very cool.

And if it looks cool enough and I go that route there are always way to make it work. I may have to cut a hole in the floor pan and sling a net for my butt to sit down in but if looks cool that is all that matters lol.

Good luck!
 

coyotedav

Full Member
Joined
Jun 11, 2009
Messages
319
Loc.
queen creek
i have passed this thread up soo many times because i could not belive anyone could lower a bronco!!!! but after reading this and seing pictures i would love a lowered bronco. the only thing holding me back is .....the $$$$ .. lack of funds!! .. $$$$$$ nice!
 

behemoth

Bronco Guru
Joined
Jul 2, 2003
Messages
1,736
Well I put it on the scales today to figure out the front spring rate. The truck is a fat little piggy. It weighs in at 2920lbs 1300 in the rear and 1600 roughly up front. There was junk in the bed so it is actually a little lighter in the rear than what these weights are, but no gas so it will hopefully come close.

So explorer 5.0, aod, explorer rear and all stock bronco steel parts. No hardtop.
 

behemoth

Bronco Guru
Joined
Jul 2, 2003
Messages
1,736
The scales max is 5k so I am hesitant to drop the big truck on them to see what it actually weighs just to compare the two.

Still figure that a 94" wheel base and 2900lbs is still smaller and lighter than a mustang. with a good balance front to rear.
 

73stallion

Bronco Guru
Joined
Mar 5, 2004
Messages
16,786
Loc.
Eugene, OR
well mine weighed 4200 before i changed bumpers, lifted it, and still had the hard top on. figure i'm about 4300 now with the lift, bumpers, and no top. i may drive t down to rincon truck this week and see what it really weighs, i'm curious.
 
OP
OP
greatguy57078

greatguy57078

Contributor
Bronco Guru
Joined
Jul 15, 2006
Messages
3,430
I have NO idea how you have the energy to coach and do this other stuff. Sometimes I feel like all I do is wake up go to work, travel for work come home at some point after I leave, sleep, wake up and do it all over again. Some of the flights I take for work are 25-26 hours not including lay overs. Those thing suck the life out of me...

Good luck!

Trust me I hear you there! I get up at 3:45 every weekday, and work from 5:00 AM-3:30 PM. Then practice from 4:00-6:00, and paint soccer fields after that. I try to get to bed by 10:00 PM, so after I get home and eat supper I am looking at the clock doing the math about how many minutes I have before I have to turn the lights outs! I do it entirely for the kids, as it pays very little and would not even cover your gas bill let alone hotel, etc.

What I try to do with the Bronco is accomplish the look I want, as well as the driveability. I hope to end up with the lowered street machine that I have dreamed of creating for years. I collected parts (and as some know still am collecting!) for quite awhile, and have been in the building process for about a year. If I was going to cut corners I would have been driving this thing by now. I have alot of of parts I could use that would make it a much easier project. My goal now is to have this running by next summer and take a couple of road trips so we can meet some of you fine folks and throw back a few cold ones. I'm not getting any younger you know!

Thank you all for your support. I can't speak for Bill and the others, but it really does give me a lift to read your posts. Keep them coming, because I need every one of them! Take care!
 
OP
OP
greatguy57078

greatguy57078

Contributor
Bronco Guru
Joined
Jul 15, 2006
Messages
3,430
Well I will weigh mine tomorrow am hopefully and put this spring rate issue to rest.

All I can say this week is do not get attached to the inner fenders as well as the flat inner fender steel. With the arms flat or parallel to the ground running these wheels and the amount we have lowered the trucks we have a problem.

Now I need to figure out the up travel amount with these systems then I will know how much to clearance the inner fenders.

You will have to take some measurements and make a template so I can see where your cuts are. I am using the 4.6 DOHC engine, so I am sure that it will be just a bit tighter in there. I was thinking that I would move the inner fenders around if needed. I know that with the Mustang II front end the bottoms will have to be trimmed anyways, so I figured that I may have to move them outwards as well, to make room for the 4.6. I love a challenge (I guess!).
 

behemoth

Bronco Guru
Joined
Jul 2, 2003
Messages
1,736
Interesting schedule you have there.

I get up at 330 am and start work at 530 67miles away. Work till 4 and drive home that is usually a 530 home time. I do not coach and am still amazed that you have the time in that schedule to do it as well.


I will look at the inner fenders after I get it running, I am really curious about the used engine I have in there, it has been a long time sitting on the stand and in the engine compartment waiting.

Hopefully the inner fenders are just a swap sides and trim them out a bit. The inner fender support(s) are more of a concern. I figure it will be easier to tube the front but that is not what I want to do. I am trying to keep it very stock appearing except for the drop. The inner fenders can be trimmed and shortened with the mustang front suspension. I will probably move the battery back to the area just above the heater tubes, and go with a smaller odyssey battery than the optima I have in there now.
That is my plan now but who knows once I get started.
 
OP
OP
greatguy57078

greatguy57078

Contributor
Bronco Guru
Joined
Jul 15, 2006
Messages
3,430
This is the last week of regular season, and the playoffs and State Championship are next week. I promised my daughter I would make it to the rest of her cross country meets, so I guess I still have 1 or 1 1/2 days on the weekends and then the weekday evenings to get some work done and a few pics along the way (of course!). I am hoping things move fast, but we all know that's wishful thinking!
 
Top