• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

MIG Welding Floor Pan

BoltBuster

Bronco Guru
Joined
Jun 5, 2002
Messages
2,051
Should I disconnect the battery and ground the body to an earth ground?

I,m doing this shade tree since I don't have a garage and figured since I'm using an extension cord and earth ground may help with consistency welds.

I figured I would disconnecting the battery I would be saving the goods...
 

bmc69

Contributor
Bronco Guru
Joined
Jun 11, 2004
Messages
12,015
Can't hurt. But its TIG or AC buzzbox welding that kills electronics...MIG is usually pretty forgiving since its DC.
 

Dave

Contributor
Bronco Guru
Joined
Aug 25, 2006
Messages
2,264
Any arc welding can damage electronics and disconnecting the battery can prevent problems. But on an EB you dont have any electronics (maybe the radio) unless you have installed electronic ignition, EFI, or some other solid state devices like a GPS, radio, etc. I always do it to make it a habit. There is more of an excuse not to connect the battery on vehicles that can be damaged by not disconnecting. That being electronics that loose information like security codes, programming, etc. I was welding a trialer hitch on a truck one day. The rod holder was laying on the ground wich was pretty moist. I heard a loud yelp and went around the truck to see about 3 drops of urine in the wheel and the guys dog tearing across the yard with its tail between its legs. The tires insulate it from earth when the ground clamp is connected and the holder is on the ground. Nothing to get too concerned about unless you are going to take a wizz on the wheel. Your MIG welder shouldn't charge the wire until you pull the trigger. My old Henning Hansen MIG does hold a charge from the capacitor on the wire for some time which will make a spark big enough to trigger my helmet.
 
Last edited:

farnorthdan

Full Member
Joined
Dec 15, 2009
Messages
344
Loc.
Eagle River, Alaska
Any arc welding can damage electronics and disconnecting the battery can prevent problems. But on an EB you dont have any electronics (maybe the radio) unless you have installed electronic ignition, EFI, or some other solid state devices like a GPS, radio, etc. I always do it to make it a habit. There is more of an excuse not to connect the battery on vehicles that can be damaged by not disconnecting. That being electronics that loose information like security codes, programming, etc. I was welding a trialer hitch on a truck one day. The rod holder was laying on the ground wich was pretty moist. I heard a loud yelp and went around the truck to see about 3 drops of urine in the wheel and the guys dog tearing across the yard with its tail between its legs. The tires insulate it from earth when the ground clamp is connected and the holder is on the ground. Nothing to get too concerned about unless you are going to take a wizz on the wheel. Your MIG welder shouldn't charge the wire until you pull the trigger. My old Henning Hansen MIG does hold a charge from the capacitor on the wire for some time which will make a spark big enough to trigger my helmet.

Thats too funny Dave, maybe i could use this technique to train my dog to stop pissing on my tires, i'm getting tired of it.



dan
 
OP
OP
BoltBuster

BoltBuster

Bronco Guru
Joined
Jun 5, 2002
Messages
2,051
Now thats funny Dave!

What type of wire should I use for floor pan, Im just doing spot welding and grinding them clean?
 

JIMS74

Sr. Member
Joined
Nov 26, 2008
Messages
412
Loc.
PORTSMOUTH, VA.
does your welder have an argon gas bottle? if not I use 0.035" innercore flux wire. lot more weld splatter than gas shielded.
Jim
 

needabronco

Bronco Guru
Joined
Jul 2, 2004
Messages
6,411
Loc.
Prescott/Farmington
I'd use the smallest wire your welder can hold. I always used .035 and burned through in a few spots because it took soo much heat. A body shop buddy talked me into trying some .025 and it works so much better, less heat, better welds, and less clean up.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,112
Welding involves a lot of current (not so much voltage). Keep the ground close to what you are welding on as the current seeks the path from the welder to the ground clamp and the harder it has to work to get to ground the worse things will be. From the quality of the weld to what it hurts along the way.
When welding on the body, ground the body close to the weld.
When welding on the frame, ground the frame close to the weld.
When welding on the exhaust, ground the exhaust close to the weld.
Don't make the weld chase through random ground straps/vehicle wiring/electrical stuff to find the ground clamp.

That said, with proper ground clamp placment I will weld on half million dollar cars with more electronics then you can think of. And I don't disconnect the battery.

I actually prefer to leave the battery connected:eek::eek::eek:
Let me explain...
spikes in the electical system are nasty. capacitors absorb spikes. The battery is a giant capacitor. If there is a high voltage random static spike that hits the vehicle, that high voltage is generally extreamly low current. The battery will take it and not even flinch. No battery, or one disconnected and that high voltage is free to find a home in some electrical thing that can't take that spike. So contratory to popular teachings, I keep the battery hooked up.

The last bodybuilders guide I remember reading regarding welding on vehicles, unplug all the wires from all the electronic modules. PCM, ABS, insterment cluster, airbag module, radio, etc. Actually unplug the wires, remove the module from the vehicle if possible. I don't know anyone who does that.

Go to any muffler shop, they don't unplug anything. I have even seen them welding holes shut on a running car. "I can still hear a leak", "hold on, keep it running", buzz, buzz, "how is that?", "good", "OK, all done, you can take it now".
 

Dave

Contributor
Bronco Guru
Joined
Aug 25, 2006
Messages
2,264
Go to any muffler shop, they don't unplug anything. I have even seen them welding holes shut on a running car. "I can still hear a leak", "hold on, keep it running", buzz, buzz, "how is that?", "good", "OK, all done, you can take it now".

I've actually seen this in action. Hook the ground clamp to the tail pipe and inadvertantly zap the tailpipe bracket to the frame. Since the tailpipe bracket has rubber insulator the ground path went through the engine and smacked the ECU. I still think it a good idea to disconnect the battery at the ground cable. Its also recomended in just about every service manual and installation quide for about any weld on component. Many electronic devices, escpeially newer stuff with memory, is susceptible to electrical spikes and noise. Newer stuff if better than the older but IMO ist a good idea to disconnect the battery. I used to be pretty common for electronic voltage regulators to get smacked from welding which lead to the suggestion to disconnect the battery. Just my opinion.
 
OP
OP
BoltBuster

BoltBuster

Bronco Guru
Joined
Jun 5, 2002
Messages
2,051
Welp, I ran out of Argon for the .25 wire which isnt flux core, should I continue? I'm only filling 1/16" holes and will be grinding them back clean.
 

fordtrucks4ever

Bronco Guru
Joined
Oct 8, 2006
Messages
1,280
Loc.
DFW
I use CO2 for a gas shield. Its extremely cheap and a bottle lasts forever(gas over liquid). Its too easy to make larger holes with flux core wire on thin sheetmetal. It also undercuts around the edge of weld. I wouldnt risk using anything but gas shielded 0.023/0.025 on body panels.
 
Top