• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

more full width axle questions

mavereq

Bronco Guru
Joined
Feb 19, 2009
Messages
2,092
yes, i used the search feature. i still have more questions.

i picked up a set of axles from a 79 f150 today. unfortunately they have the cast wedges, unlike what the ad on craigslist said. at least it gave me a bargaining chip to talk the price down with.

1. i'm not planning on narrowing these. i'm going to run a 17" wheel with more backspacing.

2. i plan to put longer radius arms on. from what i remember of geometry class, if the wedges are spaced further apart then that will move my radius arm brackets forward on the frame a bit. does anyone know about how much? also, any recommendations on extended arms that would work better with the wider spacing? i am thinking of just modifying my stock arms but haven't decided yet.

3. what should i do with my coil spring cups? the holes that are drilled in them now are off center. can i just flip the cups 180* or is that not enough? i read that some people redrilled holes.

4. has anyone used the f150 tracbar mount and just used an adjustable tracbar? it looks like i can't really raise it any without moving the mount inboard because of the design of the spring cups. i guess i'll have to get the housing mated up to the frame to see what angle my steering is at and then just go from there.

5. this axle already has disc brakes on it. it looks like the hub and rotor are one piece. i saw on wildhorses that they sell separate hubs and rotors. is that a good investment?

6. it looks like i can just reuse the steering center link and possibly just flip it over for the tro conversion. am i missing something on this? it looks way too simple and i know murphy won't allow that.

any and all pics would be appreciated. well, as long as they aren't of your scrotum. thanks for the help.
 
OP
OP
mavereq

mavereq

Bronco Guru
Joined
Feb 19, 2009
Messages
2,092
and now i can't remember who made the kit to extend your stock radius arms. anyone know?
 

barnsbronco

Jr. Member
Joined
Dec 21, 2003
Messages
92
This spring I just did this swap with a set of axles from a 79 Bronco and truthfully the swap is not that bad.
To answer your first question I have cage radius arms and they bolted right up to the full width axle. I just re-drilled my coil cups and it took care of any bowing in the coils. ( I plan on moving the front axle forward sometime so I will move my coil buckets out then.) I already had an adjustable track bar but I had to lengthen it using some tubing that fit over the track bar. I just replaced all the disc brake parts and have been happy with the stock set-up. I had already drilled my steering knuckles for heim steering so I just ordered some new steering links and heims from Ballsistic Fab.
So far I have been way happy with this set-up. It seems that it is a lot more stable off road and it does decent on road too. Here is about the best pic I have from the front. If you want some better ones I can run out to the garage and take a few just let me know.
broncosafari2009040.jpg
 

fdezone

Sr. Member
Joined
Sep 28, 2006
Messages
634
Loc.
Fredericksburg, VA
Geez, what do you suffer from multiple personality disorder or something? %) Give this schitzo some time, eventually all of his other personalities will answer his own questions! ;D
 
Last edited:
OP
OP
mavereq

mavereq

Bronco Guru
Joined
Feb 19, 2009
Messages
2,092
i should have known the fellow eod guy would put a coinpurse on my thread. thanks man, it should be real easy to get people into this thread to help me out. and i'm not schizzo.... i just change plans a lot. wait till you see the powermill i'm dropping in.
 
OP
OP
mavereq

mavereq

Bronco Guru
Joined
Feb 19, 2009
Messages
2,092
This spring I just did this swap with a set of axles from a 79 Bronco and truthfully the swap is not that bad.
To answer your first question I have cage radius arms and they bolted right up to the full width axle. I just re-drilled my coil cups and it took care of any bowing in the coils. ( I plan on moving the front axle forward sometime so I will move my coil buckets out then.) I already had an adjustable track bar but I had to lengthen it using some tubing that fit over the track bar. I just replaced all the disc brake parts and have been happy with the stock set-up. I had already drilled my steering knuckles for heim steering so I just ordered some new steering links and heims from Ballsistic Fab.
So far I have been way happy with this set-up. It seems that it is a lot more stable off road and it does decent on road too. Here is about the best pic I have from the front. If you want some better ones I can run out to the garage and take a few just let me know.

i'd really like to see exactly how your drilled your spring cups. how far over did you have to drill them?
 

78Scronco

Bronco Guru
Joined
Nov 2, 2005
Messages
1,282
the hubs and rotors are/should be two seperate pieces, at least they are from the factory.
 
OP
OP
mavereq

mavereq

Bronco Guru
Joined
Feb 19, 2009
Messages
2,092
the hubs and rotors are/should be two seperate pieces, at least they are from the factory.

i'll have to check. they look like they're pressed together enough that i dont think i'll be able to just pull them apart.
 
OP
OP
mavereq

mavereq

Bronco Guru
Joined
Feb 19, 2009
Messages
2,092
barnsbronco, how much longer are the cage arms? they didn't bolt up to the stock bracket on the frame, did they? if not, how far back did you have to go, i.e. 12" extended arms but only moved the brackets back 11" because of the wider axle.
 

barnsbronco

Jr. Member
Joined
Dec 21, 2003
Messages
92
As far as the coil cups go i just drilled them as far to one side as I could. With out doing this the coils had a pretty bad bow in them. I think that the cage arms are a bout a foot longer than stock but I had them mounted on my stock axle so that is where they stayed with the full width. I can not tell that the axle moved back at all if so it is not very much.
 
OP
OP
mavereq

mavereq

Bronco Guru
Joined
Feb 19, 2009
Messages
2,092
thanks barns. when i was looking at it today it seemed like the cups would become unstable if i moved them too far inward. maybe i'll try to fab up a brace.

so you did use the stock tracbar mounting hole? is the tracbar relatively parallel to the draglink with that setup?
 

TBS-POPS

Bronco Guru
Joined
Jun 16, 2007
Messages
1,388
Loc.
valley springs, ca
Dont freak out about the spring bow. I just FW'd mine on Cage arms and they dont bow that bad. we have two set up the same way and they work fine and flex awesome.
 
OP
OP
mavereq

mavereq

Bronco Guru
Joined
Feb 19, 2009
Messages
2,092
Dont freak out about the spring bow. I just FW'd mine on Cage arms and they dont bow that bad. we have two set up the same way and they work fine and flex awesome.

how far did you move the spring cups in? it sounds like cage arms are the way to go but i hear they're hard to find at the moment.
 

getfuzzy

Sr. Member
Joined
Mar 22, 2005
Messages
530
Here's a pic of how I moved my spring cups inward[3" on each side] some say you don't have to but i wanted the spring in line. i also made a set of Lar's bars and moved the axle forward 1".
 

Attachments

  • DSCN0827.jpg
    DSCN0827.jpg
    145.5 KB · Views: 169

Pa PITT

Contributor
Bronco Guru
Joined
Jul 15, 2005
Messages
11,300
Loc.
Stephenville TEXAS
What are Lar's Bars.. And what is the bolt to the right of the ubolt under the cups .Is it just there to add tention.
 

Michaelv's69

Jr. Member
Joined
Oct 15, 2008
Messages
74
yes, i used the search feature. i still have more questions.

i picked up a set of axles from a 79 f150 today. unfortunately they have the cast wedges, unlike what the ad on craigslist said. at least it gave me a bargaining chip to talk the price down with.

1. i'm not planning on narrowing these. i'm going to run a 17" wheel with more backspacing.

2. i plan to put longer radius arms on. from what i remember of geometry class, if the wedges are spaced further apart then that will move my radius arm brackets forward on the frame a bit. does anyone know about how much? also, any recommendations on extended arms that would work better with the wider spacing? i am thinking of just modifying my stock arms but haven't decided yet.

3. what should i do with my coil spring cups? the holes that are drilled in them now are off center. can i just flip the cups 180* or is that not enough? i read that some people redrilled holes.

4. has anyone used the f150 tracbar mount and just used an adjustable tracbar? it looks like i can't really raise it any without moving the mount inboard because of the design of the spring cups. i guess i'll have to get the housing mated up to the frame to see what angle my steering is at and then just go from there.

5. this axle already has disc brakes on it. it looks like the hub and rotor are one piece. i saw on wildhorses that they sell separate hubs and rotors. is that a good investment?

6. it looks like i can just reuse the steering center link and possibly just flip it over for the tro conversion. am i missing something on this? it looks way too simple and i know murphy won't allow that.

any and all pics would be appreciated. well, as long as they aren't of your scrotum. thanks for the help.

Call John at West Coast Broncos-He has done many and he has a setup to move the spring buckets out the right way to keep the springs in line properly. You do not have to re drill your spring perch bases this way and his extended radius arms work awesome. I have this setup on my truck and having owned my first EB for 20 years, my new one works great.
 

barnsbronco

Jr. Member
Joined
Dec 21, 2003
Messages
92
mavereq, I just used the stock track bar mount on the axle and my bronco has a track bar drop bracket on it and angle of the drag link and track bar are pretty close to parallel
 
Top